The zippo lid does not close, and the upper and lower zippo lids are misaligned

This can easily happen when a zippo falls to the ground.

Misalignment like your little z is mainly due to the separation of the iron piece on the hinge and the connection point on the inner wall of the upper lid. It's not clinging to each other anymore.

You can use a screwdriver to aim at the hinged iron sheet and the place where the upper lid is welded, and gently tap the screwdriver with an awl. By striking the iron piece of the hinge tightly against the inner wall of the lid, it can be improved.

Of course, if you buy it in a specialty store, it's best to let them fix it, if you buy it online, just do it yourself, when it is very difficult to fully recover, it can only be improved.

Pay attention to be patient, knock a little bit, keep putting together to see the situation, don't pull the lid too hard and don't pull the lid directly, if you pull the lid directly, it will cause the hinge to sink into the lighter, and the consequences will be more serious.

Hope your little z can be fixed!

I've also had this situation, and I can't close it because I fell and the lid is crooked, so just gently open the lid to the maximum and close it again.

This method only makes the lid fit, but the hinges will be a little loose, but you can't see it.

If there is a break, you have to go to a repair shop.

The hinge is broken, this is best to return to the factory to repair, zippo is a lifetime warranty, you can't do it if you repair it yourself, or send it to the manufacturer to repair.

The misalignment of the upper and lower covers of the zippo is a problem with the hinges of the lighter, and the hinges need to be adjusted. The Zippo is not a gas lighter, its fuel is a very stable petroleum refining, and the flame produced by its combustion is not only safe and reliable, but also exceptionally clean and does not produce any pollution. This liquid fuel is hidden in a fiberglass movement inside the windbreak.

The ingenious windproof design has made the Zippo lighter world-famous. The windproof wall placed inside the fuselage and the unique air hole design perfectly ensure that every Zippo lighter can stay burning in windy conditions.

For nearly fifty years, every Zippo lighter has been engraved with a code representing a specific meaning on the bottom. On July 1, 1986, the long-standing coding was replaced by a new one. The year is represented by Arabic numerals, and the letters A-L represent the month, A for January and B for February.

The zippo lighter consists of two parts, the shell and the inner tank, both with the original box, the original manual, and each style has a specific number.

You can adjust the hinge behind by yourself, my zippo fell once and this problem also appeared, my solution is a flathead screwdriver and a small hammer, first observe the problem **, use a screwdriver against the hinge to slowly debug. Pay attention to the metal fatigue of the hinge, if it is broken, it will be played off. In fact, if this is your burn-in machine, and it is not too valuable or meaningful, you can just break it with your hands.

Push forward with your fingers against the back of the hinge.

The best way is to take out the inner tank, and then put a paper dish in several layers, a little thickness, and then put the dish of paper between the upper cover and the lower lid and press it.

1. Clamp the middle finger, index finger and ring finger, the middle finger is inside, the nameless and index finger are outside, the lid is in the direction of the thumb, the hinge is down, the index finger is pressed and the upper cover is pressed, the middle finger is used as the fulcrum, the ring finger is inward to open the zippo, and then the thumb ignition is completed.

2. Pinch the thumb at the bottom of the machine, pinch the middle finger and index finger on the cover, hinge towards the tiger's mouth or little finger, and then pinch hard, let the index finger and middle finger slide under the machine when pinching, and pinch the machine tightly when sliding to the fuselage, and the upper cover will bounce open due to inertia. Don't pinch too hard, otherwise your hand will hurt, and you may pinch the upper cover crookedly. Once you master the technique, you can easily bounce off.

<>2. Next, you need to put the folded note paper in the opening position of the upper and lower shells of the zippo lighter, as shown in the figure below.

3. The right hand needs to be gently pressed down to adjust the upper cover of the ZIPPO lighter, and the left hand controls the downward direction of the upper cover of the ZIPPO lighter, as shown in the figure below.

4. Finally, check whether the inner tank and the outer cover of the zippo lighter are fully fitted, and repeat the third step if they are not fully fitted, so that the problem of loose hinges and shells of the zippo lighter can be solved.

Hello, if you don't install the zippo liner, you can see if you can cover it tightly, if you can adjust the position of the baffle on the inside of the upper cover (pull it lightly in the direction of opening the upper cover, don't use too much force); If you don't install the inner tank and don't fit it tightly, you can remove the inner liner, play the playing cards horizontally to the middle of the upper and lower covers, and press down the upper cover to solve the problem! I seem to have replied before.

This is usually caused by the hinge. It is possible to adjust the hinge, but zippo has this problem, even if it is brand new from the manufacturer. If you are a veteran, you can adjust the hinge, if you have not been in contact with the zippo for a long time, you should not adjust it, it is easy to break if there is a slight mistake.

And even if it is adjusted, it will still appear in future use. The one you said is fine, it's normal, it's like this with all zippos!

There are two main reasons that affect the smooth "opening and closing" of the upper cover: one is the hinge, and the other is the cam and the shrapnel under the cam; Because the new ZIPPO is in the "run-in period" at this stage, after using it for a period of time, this problem will be solved naturally, and there is no need to deliberately speed up the run-in speed for the sake of a moment, and use it when it should be used!

The can't cover it should be because of the lighter hinge and the loose shell. The solution is to put the folded sticky notes in the opening position of the upper and lower shells of the ZIPPO lighter, and then gently press down with the right hand to adjust the upper cover of the ZIPPO lighter, and control the downward direction of the upper cover of the ZIPPO lighter with the left hand.

<>2.After finding the reason for the loosening, we can take out a cigarette box and cut a long strip on the cigarette box.

3.Attach a long strip of cigarette pack paper to the left side of the lighter's liner. As shown in the figure below.

4.Then put the lighter with the paper of the cigarette pack attached to it inside the lid of the lighter.

1. The most commonly used method of opening the lid of Zippo is the instantaneous opening method, the middle finger, index finger, and ring finger are clamped, the middle finger is inside, the nameless and food are outside, the lid is in the direction of the thumb, and the hinge is down.

2. Press and hold the upper cover with your index finger, use your middle finger as the fulcrum, and open the zippo with your ring finger inward.

3. Finally, you can use your thumb to ignite, this is a more commonly used method in daily life, the requirements for skills are relatively low, you should pay attention to the position of your hands, and adjust the practice according to your own habits.