What should I do if the main gate of several families together jumps and can t close?

Find an electrician to help you overhaul it, and that's fine; If you overhaul it yourself, first disconnect the electricity of a household, close the main switch, operate in turn, and close the household without jumping, that is, the problem place can be repaired indoors.

Where there is a short circuit and leakage, all the feed switches except the main power switch are pulled off, and then all the way to close, which way can not be closed, which way has a problem, and then check what electrical appliances are connected on this road, and then the electrical appliances of this road are powered off or unplugged in turn, and then the switch is closed and the electrical appliances of this road are started in turn, and the switch trips after starting the electrical appliances, then there is a problem with the electrical appliances, and then check for this electrical appliances.

Check the electrical circuit first to see what causes the short circuit to make the gate unable to close. Troubleshoot and close again. If the appliance is not faulty, it is possible that the main gate is broken and needs to be replaced.

This problem must be a trip caused by excessive current, and the fault needs to be found and then repaired before it can be closed, or each family turns off the power supply at home and turns it on one by one to see which one is causing it.

In this case, there is a phenomenon of leakage and grounding in these households, so the main gate always trips, and professional electricians should be asked to investigate from house to house to find out the hidden dangers and ensure the safety of electricity.

Looking for a property to find an electrician, it is best to leak the insurance for each use, always empty, and the back of the leakage of the insurance family one. Do not interfere with each other.

You can first find the property to inspect and repair, if there is no property, you can call ** to your local power supply bureau for repair.

One of the households had a short circuit in the wiring, so a professional electrician was hired to deal with it, and then a switch was installed in each household. If you encounter the same problem in the future, you can quickly find out which line has a problem.

Inspect the house from house to house for overpower consumption.

Find a property to separate the circuits.

1. Since the opening is the electrical component that controls a single channel, and the main switch is the sum of each channel, when the current or voltage of each road is higher than the setting of the main switch, it may jump.

2. The main switch tripping should generally be a problem with one or several roads, and the failure to trip the shunt may be due to the fact that the controller setting may not match the circuit currently controlled, and it is recommended to check.

It's tripped, the opening is disconnected, and the main gate still can't be closed?

Dear, hello, tripped, the opening is disconnected, if the main gate still can't be closed, you can check whether the main gate has a control lead, whether it is remotely controlled and opened, or there is no electric trip type, and the upper port cannot be closed without electricity. Start from the lower port lead of the main gate to check, whether there is a short circuit grounding place, do not remove all the lower lines of the main gate, try in closing, if it is not closed, it can only be a fault of the main gate, replace it. Dear, <>

The above is the answer to the answer that I have summarized for you, I am very happy to serve you, please give me a thumbs up, thank you very much for your <>

I hope mine is helpful to you, and then I hope you are happy every day, have a happy life<> good luck and good luck always accompany you<>

The house tripped and couldn't close at all, thanks to the old electrician who told me that the button had to be pressed.

Before closing, press the square blue button on the leak to reset, and then close.

The main gate at home always jumps, and the gate does not jump.

Hello 1, because the positive flush gate is the control of a single circuit of electrical components, and the main gate is the sum of each channel, when the sum of each road comprehensive current or voltage attack is higher than the main gate setting, it may jump. 2. The main switch jumping should generally be a road or several roads with a question of the Zen bridge, and the branch does not trip may be that the controller setting may not match the circuit currently controlled, and it is recommended to check.

Possible reasons are:

1. The opening gate is large and the main gate is small. Cause the main gate to overcurrent trip.

2. The screws of the fixed wire of the main gate are loose, causing the temperature of the fixed place to trip too high.

3. The wire from the main gate to the opening gate is too thin, and the wire temperature is high and tripped.

4. The wire from the main gate to the opening gate will be connected to the phenomenon of short circuit.

5. The main gate itself is faulty, resulting in tripping.

To sum up, the cause can be found and dealt with step by step.

Find a professional to check if there is a short circuit or overloaded equipment.

Hope it helps.

The family does not jump the main gate often, thanks to the old electrician, it turns out that this is the case.

There is a place where the end of the line is exposed in the air conditioner, because according to what you said, sometimes it is opened for an hour or two before jumping, which should be the result of the softening and thinning of the envelope of the wire.

The incoming wire should not have a large area where the end of the wire is exposed, and there may be thin insulation, which is more difficult to check, but if you are careful, you can find it.

Answer hello, 1The rated current of the sub-switch is greater than that of the main switch; 2.The action time of the sub-switch is greater than that of the total switch 3The total switching current is too sensitive; 4.The total operating current of the sub-switch is greater than the total switching operating current; 5.Aging of the switch or quality problems.

I hope it helps, I wish you a happy life, and if you can, you can give a thumbs up oh, thank you [flowers].

Every time it trips, it is open and does not trip, what is the reason for jumping the main gate? Old electrician: It's nothing more than these 5 kinds of faults.

If you don't jump the switch, you always jump the main switch, few electricians know, in fact, there are 5 reasons, one point is thorough.

You question! 100% it was a short circuit somewhere in the house!!

1. There is a short circuit in the air conditioning line, 2. Check the insulation of the entrance line.

Is there a problem with the outdoor unit of your air conditioner.

Need to be clear"The socket does not work"What does it mean!

1)) If only the gate of the tube "socket" keeps jumping, it means that the load in the socket is too large, and it is necessary to calculate whether the capacity of the gate is insufficient or some electrical function problems; Resulting in an overcurrent!

2)) If the leakage protection of the "socket" trips, then find out the leakage of the electrical appliance.

It's a problem with insurance, the electricity consumption at home is relatively large, and the fuse is not used, so tripping, if it's not frequent, you can ignore it, and if it's often like this, you can change to a larger fuse.