How to install the aluminum square pass? What is Aluminum Fangtong?

Aluminum Fangtong installation node:

Aluminum square through ceiling installation method:

1. Pay-off. According to the floor elevation level, according to the design elevation, along the wall around the ceiling elevation level, and find out the center point of the room, and along the elevation line of the ceiling, with the center point of the room as the center on the wall to draw the keel binning position line.

2. Install the main keel boom.

After springing the ceiling elevation level line and keel position line, determine the elevation of the lower end of the boom, install the pre-processed boom, and the boom installation is fixed on the ceiling with a diameter 8 expansion bolt. The boom is made of 8 round steel with a diameter, and the spacing of the boom is controlled within the range of 1200.

3. Install the main meridian bone.

The main keel is generally C38 light steel keel, and the spacing is controlled in the range of 1200. When installing, the hanging parts matched with the main keel are used to connect with the boom.

4. Install the side keel.

According to the ceiling net height requirements around the wall with cement nails fixed 25 25 paint keel, cement nail spacing is not more than 300.

5. Install the secondary keel.

According to the specifications and dimensions of the aluminum ceiling, the secondary keel matched with the plate is installed, and the secondary keel is hung on the main keel through the hanging piece. When the length of the secondary keel needs to be extended by multiple continuations, the secondary keel connector is used to connect the opposite ends while hanging the secondary keel, and is straightened and then fixed.

6. Install the metal plate.

When the aluminum ceiling is installed, pull a reference line in the direction of the vertical secondary keel in the middle of the assembly area, and align the baseline to install on both sides. When installing, handle it gently, and you must press both sides of the square plate lightly in the order of the flanging part, and then push it tightly after being stuck into the keel.

7. Clean up. After the aluminum ceiling is installed, the board surface should be wiped clean with a cloth, and there should be no dirt and handprints.

8. The following documents and records should be checked during the acceptance of the ceiling project.

1) Construction drawings, design descriptions and other design documents of the ceiling project;

2) Product qualification certificate, performance test report, entry acceptance record and re-inspection report of the material;

3) Concealed project acceptance records;

4) Construction records.

Aluminum square pass (U-shaped square pass, U-shaped groove) is one of the ceiling materials produced in recent years, aluminum square pass has an open vision, ventilation, breathability, its lines are bright and neat, the hierarchy is clear, embodies the simple and clear modern style, simple and convenient installation and disassembly, has become the main product of the decoration market in recent years.

Wood grain color concave and convex Great Wall aluminum veneer.

According to the required horizontal height, the horizontal line needs to be pulled, both vertically and horizontally. Hoist the light steel keel at a suitable spacing.

38 or 50 keels), the general spacing meters, boom distance according to the provisions of the light steel keel distribution. The pre-installed hanging parts on the keel, together with the hanging piece keel are installed under the light steel keel, and the spacing of the hanging piece keel is generally 1 meter, and it must be adjusted to the level after all installation. Place the aluminum square.

The ceiling is buckled on the keel in order, and then the inverted cleats are pressed down, and the end of the square pass should be kept at a distance of 10mm or 20mm.

Aluminum square pass can be mainly divided into aluminum plate aluminum square pass and profile aluminum square pass.

The aluminum plate aluminum square pass is formed by continuous rolling or cold rolling, and the installation structure is a special keel buckle structure, and the installation method is similar to the ordinary strip buckle plate, which is simple and convenient, and is suitable for interior decoration (the keel can be designed with a windproof card code).

The installation structure is the use of the upper main bone, and the screws and special components are connected with the profile hammer, which is windproof and suitable for outdoor decoration (keel spacing can be adjusted arbitrarily). The special aluminum square can be stretched and bent into an arc, and the appearance of the curved aluminum square provides designers with a broader space for imagination to create more unique and beautiful works.

The installation of different aluminum squares can be selected with different heights and spacing, one high and one low, one sparse and one dense, coupled with reasonable color matching, so that the design is ever-changing, and different decorative effects can be designed. At the same time, because the aluminum square pass is transparent, the lamps, air conditioning systems, and fire-fighting equipment can be placed in the ceiling to achieve a perfect visual effect that is consistent as a whole.

The installation of the aluminum square pass is simple, and the maintenance is also very convenient, because each aluminum square pass is separate, it can be installed and disassembled at will, without special tools, which is convenient for maintenance and maintenance.

1. Choose aluminum square pass as the decoration material of the exterior wall, its decorative effect is very ideal, the first need to prepare materials before the installation of hail diggers, there are main skeletons, columns, and grilles, including embedded parts, channel steel, screws, embedded plates and so on. 2. The embedded parts should be fixed first through the expansion screw. In the later stage, it is also necessary to pass the inspection of Party B, and after there is no problem, the source school can weld the main skeleton, and it is necessary to adopt the welding method.

The upper fixing needs to be used as the support point through two grooves, and the lower fixing needs to install the embedded parts to the position where the column has been buried, and then the column is welded on the embedded plate. 3. Then install the grille, and the grid and the column can be connected by corner code. At the same time, it is also necessary to set the spacing between them, for example, it can be maintained at about 125 mm.

Aluminum Fangtong installation node:

Aluminum Fangtong can be customized according to specifications, and the specifications of conventional mechanical automatic roll drawing forming: width: 20 200mm, height 20 300mm, thickness.

The specifications commonly used for aluminum square are: 30x50 mm, 30x80 mm, 30x100 mm, 40x60 mm, 40x80 mm, 40x100 mm, 40x120 mm, 50x50 mm, 50x80 mm, 50x100 mm, 50x120 mm, 50x150 mm, etc. In reality, the specifications of the aluminum square pass are abundant, usually the bottom width is 20-400 mm, the height is 20-600 mm, the thickness is mm, the length is within 6 meters, and the special size can be customized and processed.

In this regard, the relevant high-quality enterprises in the industry can do it both in terms of machinery and equipment and technology.

How to install the aluminum square pass?

1. Install the aluminum trimming corners according to the same horizontal height.

2. Hang the boom and light steel keel according to the appropriate spacing, the spacing of the boom is less than or equal to meters, and the spacing of the light steel keel is meters.

3. Connect the hanging parts pre-installed on the triangular keel together with the triangular keel and the light steel keel in a vertical direction according to the plate spacing, and then adjust the level.

4. Press the two sides of the square plate into the triangular keel seam in parallel, first install the two ends of the horizontal direction to find the right angle, and then pull the straight line to gradually row a row of buckling plates, and adjust each row after the buckle to ensure that the plate surface is smooth and the plate seam is vertical. (Note that the direction of the small pit on the side of the square plate is inserted into the seam of the triangular keel).

5. Wear gloves when gussiping the plate, if you accidentally leave a stain on the board surface, wash it with water, and it is forbidden to tear off the protective film during installation.

Subway shape two-color aluminum square profile.

Dear, hello, I am happy to answer for you, how to install the outdoor aluminum square A: The installation method of the outdoor aluminum square pass is as follows: first, fix the ceiling height.

Second, the boom is fixed. The distance between the booms is fixed, usually between 1 meter. Third, after the boom is fixed, the bones of Long Shenhuai are fixed.

Fourth, after the keel is fixed. A wrench is required, and the connection points of the skeleton and the boom should be fixed and strong. Fifth, install the aluminum square pass.

Regret filial piety code Aluminum square pass beyond the normal range of the need to cut the cover song tool cutting. Pay attention to which item is the aluminum square pass and the keel must be vertical The distance between the aluminum square pass and the aluminum square pass is the spacing of the keel.

Wall aluminum square is a commonly used decoration material, with beautiful, durable, easy to clean and other characteristics, favored by the majority of consumers. So, what is the installation method of wall aluminum square pass? Let's take a closer look.

1.Measure the dimensions and installation location.

Before installation, the dimensions of the wall and the installation position need to be measured beforehand. First of all, the floating ash on the wall should be removed to ensure the flatness and stability of the wall. Then determine the length and width of the aluminum square pass according to the size, and at the same time determine the installation position and quantity.

2.Set up the mounting frame.

When installing the aluminum square pass, you need to set up the frame, and the setting of the frame needs to be adjusted with professional tools. First of all, it is necessary to measure the position of the hole that needs to be opened in the wall, and then use equipment such as an electric drill to punch the hole in the wall. It is set according to the pre-measured dimensions so that the aluminium square can be perfectly integrated into the wall.

3.Install the aluminum square pass.

After setting up the frame, the next step is to install the aluminum square pass. First of all, it is necessary to connect the Weixiao aluminum square pass with the frame and fix it with screws. During the installation process, it is necessary to pay attention to the installation direction and position of the aluminum square pass, and at the same time use the trembling lead level to ensure the levelness of the aluminum square pass.

4.Examine. After the installation of the aluminum square pass, it is necessary to check whether there is any loose or uneven phenomenon. If there are the above problems, it needs to be trimmed to ensure the firmness and flatness of the aluminum square pass.

Summary: When installing the wall aluminum square pass, it is necessary to follow certain steps to ensure the quality and aesthetics of the installation. When purchasing aluminum squares, it is necessary to choose high-quality, non-deformable aluminum alloy materials to ensure a long service life.

The color of the aluminum square pass ceiling is generally no color difference, and the following points need to be paid attention to when customizing the aluminum square pass to avoid color difference:

How to avoid the unevenness of the flat top of the aluminum square pass, the following points should be paid attention to when installing: Yuanshi 1, the purchased aluminum square pass and its supporting keels and accessories should meet the product quality requirements, and there should be no bending and deformation; 2. In the process of transportation and placement, it should be set aside flat, not pressurized, and avoid the erosion of high temperature and harmful substances; 3. The keel is installed smoothly and aligned, and the spacing deviation should be controlled within the allowable range; 4. During installation, if there is a deviation in the size, it should be adjusted first and then inserted in order to insert the orange limbs, and should not be inserted hard to prevent deformation; 5. Large lamps, exhaust fans and other objects should be set up with another spreader, which should not be directly placed on the flat, and should be reinforced at the installation of lamps and lanterns. As long as the above points can be achieved, the aesthetics of the decorated ceiling are almost perfect, which can effectively avoid the unevenness of the aluminum ceiling.

<> the aluminium square ring installation in the lobby of the subway station.