The overshoot distance of the servo system is getting larger and larger during operation, how to sol

The offset problem is the use of stepper or servo motors.

One of the common problems faced by equipment manufacturers in the process of equipment installation and commissioning and equipment use. Misalignment can be caused by improper mechanical assembly, control systems and drives.

Signal mismatch, or electromagnetic interference within the device.

The equipment in the workshop interferes with each other or the ground wire is not handled properly during equipment installation.

Among the many application cases, the most common deviation causes and countermeasures are extracted to help the commissioning personnel of the equipment manufacturer quickly locate the problem, take various appropriate measures to improve the anti-interference of the equipment, and ensure the normal operation of the equipment for correct grounding.

The overcharge distance of the servo system is getting bigger and bigger during the operation, and you see if this problem is because they have been using some parts of it for a long time, well, Taisong is engaged in this, you can shorten his distance a little bit, and see if it can be solved.

As the distance grows, the machine needs to be regulated or the operating system needs to be updated.

If his impact distance is getting bigger, then you should make his distance a little smaller.

If the distance of the servo system is getting larger and larger during operation, this should be seen to see if its current is gradually increasing.

In the process of operation, the process distance of the city service system is getting larger and larger, and how to solve it is getting bigger and bigger, and the solution to this problem must be solved in a proper way.

Now we are all in the recipe character series, and we are running it in the process of its overshoot distance is getting bigger and bigger, and I think it can still be adjusted by our own choices.

The servo system is running more and more in the process of rushing distance, you need to adjust it, he produces more and more distance.

If he's getting more and more away, then you have to adjust his spacing to be safe.

The distance of the servo system is getting bigger and bigger during operation, which means that the friction inside is getting bigger and bigger, and you need to adjust it.

The distance from the slave system is getting bigger and bigger in the process of operation, and how to solve the distance is getting bigger and bigger, so the distance should be narrowed.

Motion control in the city service control system is still difficult to achieve.

It's normal for it to get bigger and bigger in the process, so it's much better if you need to redo the system.

Well, if the servo system is running more and more during the impact distance, this may be the problem with the Lianzhou solution, you can participate in the weekly inspection.

The process distance of the private server system is getting larger and larger during operation, and if you want to solve it well, you must adjust the process distance to the most moderate is the best.

The impact distance of the system is getting larger and larger during operation, and how to solve the problem is, of course, to ask some professionals to repair and inspect it to solve the problem.

You can directly contact their official staff to help solve the specific solution.

Half is caused by the unsuitable gain, and the bai overshoot is generally the proportional gain is too large.

Appropriately reduce the proportional gain of the speed ring should solve your DAO problem, open the function of the servo debugging software trace or oscilloscope, observe the change of the waveform, and slowly adjust to the motion curve you want, the actual speed curve is an important indicator of whether the operation is stable or not.

The proportional gain should not be too small, otherwise there will be another phenomenon of shaking and shaking (the gain is too small), and it will be too large for the original ** and overshoot.

There is also a parameter, integral gain, that works with this parameter.

Roughly the original ** dynamic and overshoot, appropriately adjust the proportional gain, slightly increase the integral gain. A shake is to increase the proportional gain and narrow the integral gain. The effect of the integral gain is smaller than that of the proportional gain, but these two are parameters that are in harmony with each other.

The life system is better than the impact in the process of operation, and the intensity is getting bigger and bigger, and this can be solved.

The system is getting bigger and bigger in the process of Yuncheng, how to solve it can be solved directly by looking at it and the specialist will help you solve it.

How to solve this problem in the past during the operation of the servo system.