Ask about the distorted sound of the electric guitar

Sound is vibration. "Sound waves" are generated.

The electric guitar mainly uses a pickup (the same principle as a microphone) to play the sound through the amplifier (speaker).

An acoustic electric guitar is like playing an acoustic guitar into a microphone. It's just that what you say is not distorted.

Distortion, on the other hand, is the use of effects to overload and distort the audio to make some sound effects. It is by no means the sound of the gong being struck as mentioned in Makoto 110, of course, if you want, you can do it like that, and it is theoretically possible.

It's hard to get a good distortion, and most commonly used effects will have a classic timbre parameter table that someone else has made. Doing it yourself is a skill.

I'm sure you've heard of electric guitar distortion, but you just can't tell. The most popular SHE's Super Star background** is distortion.

The first 20 seconds or so are acoustic (no distortion, of course, this acoustic is also processed with effects), followed by more typical metal distortion. You can compare.

At the beginning, it was distortion, and later strumming was not.

Ren Xianqi's "I Am a Fish".

Break up chords with yes chorus effects, lead guitar with distortion effects.

You must know that the prelude to really loving you is distortion.

Undistorted and similar to an electric box piano electric guitar plus effects like an electronic keyboard have a lot of tones.

Hello, dear is happy to answer for you. First, connect the guitar to the effect banquet booth with a cable and connect it to the speaker. Then open the volume knob halfway, or adjust it according to the volume of the actual speaker.

Then turn the gain knob. Basically, it's halfway through. This knob is used to adjust the degree of distortion.

The next thing is to press the button in the middle of the bottom.,This is generally a switch between distortion and original sound.,Generally the green light is on the distortion.,When it's off, it's the original sound.。 The other knobs try to adjust themselves, basically some to adjust the timbre, high and low. Dear, I hope mine can help you, if you are satisfied with my service, please give a thumbs up, I wish you all the best!

There may be several reasons for the distortion of the electric guitar audio output:

1. The speaker and the audio output impedance do not match, in this case, the audio output impedance is generally greater than the speaker impedance.

2. The signal input impedance does not match the audio input impedance. You can make a matcher using the following circuit diagram:

3. The output signal of the electric guitar is too strong, and the sound is slightly louder, and the horn will make a hoarse sound. The solution is to connect a resistor of tens of hundreds of ohms in parallel to the output of the electric guitar to attenuate the input signal.

4. The amplification gain of the pre-amp voltage of the electric guitar audio is too strong, resulting in the distortion of the post-amplification power amplification output.

5. Add a bypass capacitor of hundreds or thousands of pico-methods to the ground to the audio input end to filter out the unwanted signal.

The purity of the sound changes, it becomes harsh.

Guitar distortion, literally, of course, is to lose the real thing, for guitar effects, to a large extent, to the top and bottom distortion, that is, to amplify the sine wave well, put it too big, the circuit can't stand it, the peaks and troughs can't come out, it becomes a straight line, so the rounded sine becomes something similar to a square wave, and it is naturally harsh.

The knob that controls the degree of overload is the WR1 potentiometer at the top, the larger its value, the greater the magnification, the maximum can be 1m, then of course it is too big, distortion. Turning it off is just a big one, and it won't be distorted, because it doesn't exceed the maximum voltage of the amplifier.

There are also three diodes, which can play a role in limiting the voltage, generally a diode is considered to occupy the left and right voltage, of course, there will be a little fluctuation, not too large. When the magnification is too large, the diode will also work, clamping the voltage at both ends of the potentiometer, which is also a truncation (top and bottom) effect, and it is not absolute.

Because as mentioned earlier, the voltage is not strictly so many volts, this truncated waveform is not a horizontal line but a skewed line, and then look closely, you can also find that the positive voltage and negative voltage diodes are not the same, that is to say, even if the input is symmetrical, the output is also asymmetrical, in short, the waveform is tangled.

The sound of the electric guitar playing is dry, probably because the sound is not accompanied by the use of appropriate sound equipment and processing methods, resulting in a thin and dry tone. Some of the common reasons are as follows:

1.No effects: Using guitar effects, such as the right ones for reverb, distortion, chorus, etc., can give the guitar a richer sound.

2.The filter of the guitar amp is not good enough: If the filter quality of the amp is not good enough, it will affect the quality of the sound. Buying high-quality speakers, amplifiers and other sound processing equipment can bring better sound effects.

3.Lack of playing skills: The guitar's playing skills and techniques also have a certain impact on the sound. There are different strumming techniques that can change the sound of the guitar playing and make it sound more expressive.

In short, if you want the guitar to play a richer and fuller sound, you need to pay attention to the selection and use of equipment, as well as the improvement of playing skills. If possible, you can also experiment and adjust to find the most suitable sound treatment.

There are many reasons why electric guitars appear to have a dry sound. First of all, it may be that the volume of the speaker is too low or the sound setting is ineffective. Second, it could also be that the effects aren't set up properly and need to be adjusted.

Third, it may be that the line connection is questioned, and the plug socket is loose or the contact is poor. It is also possible that the guitar strings are not new enough and need to be replaced, which will also affect the sound performance. There may be many more reasons, but in order to correctly solve the problem of filming wild duels, you need to investigate the causes one by one.

When using an electric guitar, you should first make sure that the surrounding environment is quiet, and then carefully check whether each part is working properly and troubleshoot the problem one by one. At the same time, it is also necessary to pay attention to the maintenance of the guitar, and the chain regularly replaces the guitar strings and cleans the body to ensure that the guitar is in good condition and obtain a better sound performance.

The sound of the electric guitar playing out of the air does Kai to dry up for a couple of reasons. First of all, it may be because your amps or speakers are not good enough to fully restore the sound of your electric guitar. Secondly, it may be because your guitar tone is not the right one, or your playing skills need to be improved.

Finally, it may also be that the quality of your electric guitar is not good enough to produce a fuller and richer tone.