How to install the curtain track pulley and how to replace the curtain track pulley

This depends on that track.

What it looks like, and if there are any empty ones on either side of the track. If there are empty on both sides, the pulley can be installed, then it can be installed without disassembling the track, otherwise, the track can only be removed first, and then the pulley can be installed, and then the track can be installed in place.

Summary. 1. First of all, we need to prepare a ladder, climb up, and find a plug at the head of the curtain rod or at the tail. By removing the plug near the side of the replacement pulley, it can be removed when the pulley is being replaced.

Then take out the pulley that needs to be replaced, feed the prepared new pulley from the removed port to the curtain rod, and finally install the plug back on.

1. First of all, we need to prepare a ladder, climb up, and find a plug at the head or tail of the curtain Peihong virtual pole. By removing the plug near the side of the replacement pulley, you can remove it when the pulley is in full swing. Then take out the pulley that needs to be replaced, feed the prepared new pulley from the removed port to the curtain rod, and finally install the plug back.

2. Be cautious about renting and returning to the hands to connect the card slots and tracks of the fixing parts, embed the worn pulley track into the fixed card slot, tighten the screws, and it can be replaced successfully. Therefore, the disassembly and installation are relatively simple, and there is no technical filial piety content.

Curtain track installation method:Tools Raw materials: electric drills, curtain tracks.

1. Determine the position of the track, and then have a marker pen to make a mark, so as to ensure that the installed curtain track is balanced.

2. Use an electric drill to punch holes.

3. After punching the hole, punch the expansion rubber nail into the hole, so that the curtain track can be fixed very firmly.

4. Accessories for installing the track: there must be a lot of sliding buckles to install some, if it is not enough, it will be troublesome to install it.

5. Then fix the curtain track on the wall, fix the screws on it, you can fix it with a screwdriver (more laborious) or fix it with an electric drill. Then install the second track, and install the second curtain track in the same way, so that it is a double track.

6. After the curtain track purchased online exceeds a certain length, it will be cut, but the link accessories will be given and installed by yourself.

7. The same installation method is applied to the curtain track in other locations.

8. After the curtain track is installed, you can hang the curtain.

1. Positioning.

bai。The accuracy of line positioning is related to the success of curtain installation. DAO first measures the interior.

The distance between the fixing holes and the size of the mounting track required. Curtain Rails Installation Curtain Rails are available in single, double or triple rails. If the width of the window is greater than 1200 m, the curtain should be separated and bent when bending, the bend should be flat, the bend should be gentle, the overlapping length should be at least 200 m, and the curtain box is usually an installation track. 牋牋牋.

When installing curtains at home, many details and accessories should be installed, such as pulleys. How to install the curtain pulley? PChouse will take you to find out.

1. Draw lines for curtain slide positioning.

The first step of curtain slide installation is to draw the line positioning, take into account the firmness of the fixation, first measure the size that needs to be installed, the curtain slide and then calculate the fixed hole distance, and then install the fixing, the curtain slide is generally the fixing for the cement wall or roof needs to add expansion screws.

2. The curtain slideway wears pulleys.

The second step of curtain slide installation is to wear pulleys, curtain slide when the window width is greater than 1200mm, the curtain rail should be disconnected, the simmering bend at the disconnection is staggered, the simmering bend should be smooth curve, and the lap length is not less than 200mm. In this way, the curtain slide can ensure the size of the force and the uniformity of the force.

3. The curtain slide is plugged and sealed.

The third step of curtain slide installation is that after the curtain is installed with pulleys, in order to avoid the slide from rolling out of the track, and also to avoid the sharp corners of both ends of the track from scratching the front of the hard injury, the curtain slideway should be blocked with a seal, and finally the curtain slide is good in the card slot and track connecting the fixings.

Draw a line. Consider the firmness of the fixing, to prevent the spacing of the fixing parts from being too large and can not withstand the tension, first measure the size of the required installation slide rail, and then calculate the distance between the fixed holes, the general spacing distance of the fixing parts is not more than 50 cm, and then draw the line, the accuracy of the curtain installation depends on the success or failure of the curtain installation.

Install the fixtures. Generally, the installation of fixtures requires expansion of screws for cement walls or roofs.

Slippery. When the width of the window is greater than 1200, the curtain rail should be disconnected, the simmering bend at the disconnection should be staggered, the simmering bend should be a gentle curve, and the lap length should not be less than 200. When slipping on the slide rail, you must pay attention to the length of the slide rail, 1 general specification is:

The one-meter-long slide rail is installed with seven slides, so as to ensure the uniformity of the force and force after installing the curtain.

After the window rail is installed and slipped, in order not to slip out of the slide rail, and at the same time, in order not to scrape the front of the two sharp corners of the slide rail, both ends of the window rail are sealed with sealing plugs, and then the sealing plug is fixed with screws.

Connect the clamping slot and slide rail of the fixing. Embed the slippery curtain slide rail into the clamping rock groove of the fixing, and then place the hoisting clip, so that the hoisting clip of the fixer is 90 degrees from the slide rail, and tighten the hoisting clip with screws, so that the hoisting clip is firmly stuck on the curtain slide rail. Through the above steps, the first step is basically installed on the curtain slide.

Curtain track installation method: line positioning, curtain rail installation, wearing pulley, hoisting clip, position adjustment.

1. Draw a line for positioning.

This is the most important part. Drawing lines is related to the success or failure of curtain installation, first measure the fixed hole spacing and the size of the installation track. Normally, the distance between the fixing parts is not more than 50 cm, and then the line is drawn to position.

2. Curtain rail installation.

When the window width is greater than 1200mm, the curtain rail should be disconnected, the simmering bend at the disconnection should be staggered, the simmering bend should be a gentle curve, and the lap length should not be less than 200mm. Among them, heavy curtain rails should be equipped with machine screws, and at the same time, the spacing should be encrypted, and the specifications of wood screws should not be less than 30mm. Bright curtain boxes are generally installed on the track; Dark curtain box should be installed after the track.

3. Wear pulleys.

Wear pulleys to the track, when wearing pulleys, you must pay attention to the length of the track, usually 8 pulleys are installed on the 1-meter-long track to ensure the uniformity of the force and force after installing the curtain.

4. Hoisting the clip.

When hoisting the clamp, the clamp should be rotated 90 degrees to connect with the track, and the hoisting clamp should be installed on the top plate with self-tapping screws. If it is a concrete structure, it needs to be expanded with screw.

5. Position adjustment.

The last link is to adjust the position, floor-to-ceiling curtains or curtains hanging over the countertop, and the width of the window sill should be given up when the track is installed, so as to avoid the curtain being blocked when it droops and appearing to be the best view.

When installing windows, you need to pay attention to the installation method of the specific track. How to install the curtain track? PChouse will take you to find out.

Set the height and position of the curtain track and purchase the appropriate specifications, and then install the curtain track and curtain rod need to be level and aligned with the installation site. The specific installation steps are as follows:

Step 1: The accuracy of positioning line positioning is related to the success or failure of curtain installation, first measure the fixed hole spacing, and the size of the required installation track.

Step 2: Know the height of the curtain to be installed and the location of the track, and buy the appropriate curtain track specifications. The bright curtain box generally needs to install the track first, and the dark curtain box needs to install the track later.

Step 3: Install the curtain track and curtain rod, complete the connection between the hoisting clip and the curtain track and install it on the top plate with screws, when installing the curtain rod, you need to pay attention to the fixed parts that should be connected first, and pull the curtain rod or iron wire to the fixed parts when you install them, and the elevation of the room must be flat, positive and consistent with the elevation of the room.