-
Automatic ice after the refrigerator freezes is not a fault, it is the function of the temperature control and defroster, which is normal:
When the refrigerator is in working condition, the back of the refrigerator will freeze, mainly in the back of the refrigerator has an evaporator.
The temperature of the cold room mainly depends on this evaporator to reach the set temperature. When the refrigerator compressor.
When the temperature rises when the operating temperature is stopped, the ice on the back of the refrigerator will melt away and turn into water droplets, which will flow down the back to the water outlet hole and then to the evaporation dish. Due to the number of times the door is opened, the increase in ambient temperature and humidity, the moisture of the food, the temperature control is not accurate, and the setting mode is not correct (low temperature compensator.
In the case of "winter"), the ice and water on the back of the refrigerator will not melt and run out, and the refrigerator will freeze when it works again.
-
What is the matter with the freezing of the refrigerator, how to get rid of the freezing of the refrigerator, the problem of freezing the refrigerator and the fact that the refrigerator is not refrigerated is always a headache. Sometimes the freezer is completely normal, but the refrigerator has a thick layer of ice, sometimes the refrigerator is normal, and the ice in the freezer is so hard that it can't be knocked down, and even the refrigerator door is frozen so that it can't be opened. What should I do?
-
It shouldn't be a malfunction, it's an automatic defrost.
-
Freeze in the fridge! Is it normal or malfunctional? How exactly should it be adjusted?
-
It's not a fault how not to freeze.
-
There are several possible causes of freezing in your refrigerator:
1. There is too much frost on the evaporator, and the water overflows the water tray when it melts and flows in the refrigerator.
2. The water tray in the refrigerator is not aligned with the water receiving funnel, resulting in the water flowing in the refrigerator.
3. The drain pipe mouth is frozen, so that the defrosting water cannot flow out, and the flow accumulates in the refrigerator.
4. Cold drinking water or other beverage containers are turned over and flowed in the refrigerator, or the lid of the beverage bottle is not tightened and is placed horizontally on the food shelf, causing the beverage to flow out.
5. Usually, the refrigerator door is not closed tightly, or the sealing strip is damaged, so that the outside hot air continues to flow in and condense into water.
6. There are too many lukewarm foods stored in the refrigerator, such as hot drinks, hot tofu, mung bean soup, etc., which instantly form a large mist and water droplets in the refrigerator, which condense into water as the temperature drops.
7. The water content of the food stored in the refrigerator is large, and with the drop of temperature, the water vapor in the food evaporates, and then condenses when it is cold, and then becomes water, which flows in the refrigerator.
The solution is as follows:
1. When using refrigerators, it is necessary to defrost frequently, which is also a measure to save electricity.
2. Adjust the water receiving funnel and align it with the position of the receiving tray.
3. The temperature in the refrigerator should not be adjusted below 0 °C, usually 2-6 °C is appropriate, so as to prevent the water from freezing.
4. When refrigerating beverages, they should be handled gently, and the plastic container with the bottle cap should be placed on the food shelf of the door leaf, and if it is placed on the food shelf, the bottle cap should be tightened to prevent the liquid from flowing out.
5. When using the refrigerator, it is an important task to open and close the door tightly, and it is necessary to be careful to prevent cold; If the sealing strip is found to be damaged, it should be repaired in time; It is also required to pay attention to whether there is dirt on the door edge and adhesive strip at all times, and if found, wipe it off immediately.
6. Hot food is not allowed to be put in the refrigerator, and it is necessary to wait for it to cool to room temperature before putting it in the refrigerator.
-
Phenomenon 1: Repeated freezing occurs in the refrigerator compartment.
First check the temperature in the box, generally speaking, it should be adjusted to 3 4 degrees, if the value is not in this range, this situation may occur, of course, if it is not a temperature problem, you should check whether the temperature of the food stored in the refrigerator is too high, you should avoid putting such items in the box, otherwise the heat will also cause a lot of condensation, which will indirectly produce this phenomenon.
Phenomenon 2: The refrigerator of the old refrigerator does not refrigerate after freezing.
Generally speaking, this situation is mainly due to the leakage of refrigerant, and the test can be done by listening to whether the compressor is running at a lower volume than usual, if so, the temperature of the condenser tube can be tested, and if the condensate is insufficient, only refrigerant needs to be added.
Phenomenon 3: The freezer compartment of the newly bought refrigerator freezes.
If this situation occurs for newly purchased products, first of all, you should confirm whether the door is closed, if not, it will also cause the refrigerator to freeze to a certain extent, of course, if it is not the reason why the door is not closed, you should check the refrigerator temperature setting problem in combination with the phenomenon, if there is no problem, you should contact the after-sales service for processing.
Phenomenon 4: The back wall of the refrigerator freezes.
This situation is mainly due to the close distance between the internal evaporation pipe and the inner tank, which causes the foam to be wetted, resulting in the formation of ice when the condensation gas spreads to the inner tank.
1. Avoid placing food with high moisture content in the box, such as some soup foods, and there must be a correct person for temperature regulation, generally speaking, the temperature represented by the value of the thermostat in most refrigerators and refrigerators is the opposite, that is to say, the lower the temperature, the greater the value.
2. Opening and closing the door frame many times will cause a large temperature difference in the box, which will cause icing to a certain extent, and if you often find a layer of ice on the back of the refrigerator, it is mainly caused by too much food, so when storing food at ordinary times, you must pay attention to the distance between the back and the back.
-
Causes of freezing in the freezer compartment of the refrigerator.
1. During the operation, the air humidity in the freezer compartment of the refrigerator is relatively large, but the evaporator temperature of the refrigerator is relatively low. After the water vapor in the freezer condenses on the inner wall of the refrigerator, it slowly condenses into ice, and eventually the ice layer accumulates thicker and thicker.
2. Under normal circumstances, after the temperature of the freezer in the refrigerator drops, the ice on the back wall of the freezer will begin to melt, and the melted condensate will be discharged into the refrigerator through the drainage hole of the refrigerator, but if the refrigerator drainage hole is blocked, then it will cause the refrigerator to drain poorly, and the water in the freezer compartment in the refrigerator cannot be discharged and condensed into ice in the refrigerator.
3. The door of the freezer compartment of the refrigerator is not closed tightly, resulting in the water vapor in the air entering the refrigerator, and the water vapor will condense into ice on the inner wall of the refrigerator after being cold in the refrigerator, which leads to the freezing of the refrigerator refrigerator.
How to deal with freezing in the freezer compartment of the refrigerator.
When we encounter the freezing of the refrigerator, we should know how to deal with it, in fact, there are many ways to deal with the freezing of the refrigerator freezer, if the freezer of your home is frozen, you can try to use the following methods to deal with it.
1. If the ice in the freezer compartment of the refrigerator is very thick, at this time, you can first pull out the power cord of the refrigerator, open the door of the freezer compartment of the refrigerator at the same time, and take out the food at the same time, so that the ice in the freezer compartment of the refrigerator will melt naturally at room temperature.
2. If the drain in the freezer compartment of the refrigerator is blocked during use, resulting in poor drainage, then too much moisture in the freezer compartment of the refrigerator will freeze, at this time, you should check it first, if the drain of the freezer compartment of the refrigerator is blocked, you can dredge the drain first, and then pull out the power cord of the refrigerator, open the door of the freezer compartment, and let the ice in the freezer naturally melt at room temperature.
3. In the case of freezing in the refrigerator freezer, in addition to using the method introduced above, you can also use this method: first pull out the power cord of the refrigerator, take out the food in the freezer compartment of the refrigerator, and then fill a bowl of hot water with a larger bowl, put it in the freezer, close the refrigerator door, in order to prevent the melted ice water from flowing everywhere, you can also put a newspaper or towel at the bottom of the refrigerator, and then check whether the ice in the refrigerator has melted clean after a period of time.
-
What to do if it freezes often 1: Take out the things in the refrigerator room and have a small hole 2: It is convenient for us to clean the small mechanism to solve the problem Open the small hole to solve the problem of freezing The ice cubes in it can melt automatically Don't use too much force.
-
There are many reasons for freezing in the refrigerator compartment, specifically the following:
1. If the temperature of the refrigerator is too low, the temperature of the refrigerator should be set between 4-8 degrees. If the thermostat is mechanical, the gear should be adjusted reasonably according to the seasonal temperature, the gear should be adjusted to 1-2 gear in summer, 3 gear in spring and autumn, and 4-5 gear in winter, keeping the temperature of the freezer room at about minus 18 degrees, and the temperature of the refrigerator room between 0-10 degrees, preferably between 4-8 degrees.
2. The door seal is not tightly sealed or the door is opened frequently or the door is opened for too long, resulting in serious loss of cold air in the refrigerated room. If the seal is not tightly sealed, the new door seal should be repaired or replaced in time, and the number or time of opening the door should be minimized.
3. The thermostat itself is faulty, resulting in the compressor working for a long time without stopping. If it is a mechanical thermostat, there are three more reasons:
1. If the temperature sensing head drawn out by the thermostat is loose and displaced, the loose temperature sensing head should be restored to its original position and fixed, so that it can be in close contact with the evaporator in the back wall of the refrigerator;
2. The internal contacts of the thermostat are sticky, and the emergency treatment method is: first cut off the power supply of the refrigerator, rotate the thermostat knob to 0 gear, and then rotate to the highest gear, so that the contacts can be separated by rotating a few more times, and then adjust the gear to 1-2 gears, and then turn on the power supply test machine after 5 minutes of power failure, if the compressor can be shut down, it is troubleshooting.
3. If the thermostat temperature sensor tube is damaged and leaked, the thermostat should be replaced with a new one, and the general electronic market refrigeration component store is about 25 yuan.
-
Most of the water vapor comes from the air, and when people store food and open the refrigerator, the indoor air and the gas in the refrigerator exchange freely, and the humid air in the room quietly enters the refrigerator. There is also a part of the moisture from the food stored in the refrigerator, such as cleaned vegetables and fruits in the crisper box, the water in the vegetables and other foods evaporates, and condenses into frost after being cold.
Especially in summer, the indoor temperature is high, the humidity is high, and the temperature difference between the room temperature and the temperature in the refrigerator is large. When the refrigerator is opened, a cool air flows from the inside out, and the indoor air burrows into the refrigerator. After a short time, a layer of hoarfrost appears on the front wall of the refrigerator.
It has also been found that even if nothing is in the refrigerator, a thick layer of frost will form in the refrigerator that is often opened, which shows that a large part of the moisture in the refrigerator comes from the moisture in the air. So it's normal. In the refrigerator, there will be ice on the back wall panel, because the back wall board is a built-in evaporator, which mainly plays a role in refrigeration, and when working, due to the low surface temperature of the evaporator, the hotter air in the room when the door is opened and closed, or the food put in it will form a thin layer of frost or water bead-shaped ice beans on the wall plate after refrigeration, which is a normal phenomenon.
The refrigerator has an automatic defrost function, which will slowly melt the frost by itself, as long as you are careful not to put the food close to the back wall during use.
-
The refrigerator rubber strip, the seal is aging, buy one and replace it.
-
Burning gas too close to the refrigerator may cause the freezer compartment of the refrigerator to freeze.
-
Have you repaired it? Is it to charge too much refrigerant or to adjust the thermometer.
-
The drain pipe freezes, so that the water in the tank cannot flow out, so that it flows in the refrigerator.
-
No, you're prescribing too high for freezing.
-
How many degrees should the ice be adjusted in the Xinfei refrigerator?
-
Summary. There are three situations of ice automation in the refrigerator: First, the freezer is in poor contact. The second is that the magnetic force of the refrigerator door is weakened, so that the air leaks. The third is that the rubber seal is damaged, which will also lead to <>air leakage
There are three situations of ice automation in the refrigerator: First, the freezer is in poor contact. The second is that the magnetic force of the ice search box door is weakened, so that the air leaks. The third is that the rubber seal is damaged, which will also lead to air leakage
Dear, I saw your question and am sorting out the answer for you, please wait a while<> dear, check whether the thermostat or main control board is normal, and the step is as follows: check whether the thermostat is in the "0" gear, if not in the Li Lu gear, and then check whether the thermostat is normal. In the case of power-on, adjust the thermostat gear to strong cold gear (no strong cold gear to 7 gear), if the temperature probe is in the box, you can also use a hot towel to heat the thermostat temperature probe to observe whether the compressor is disturbing the jujube operation.
If the compressor does not start, the thermostat may be faulty and requires further repair.
Dear, do you have any other questions?
-
1. One of the most common reasons for the freezing of the refrigerator is that the refrigerator is not closed tightly, which may be due to negligence, or it may be caused by the damage of the sealing collapse and buried strip, when the refrigerator is not closed tightly, the air outside the refrigerator will enter the refrigerator, and the water vapor brought by it is easy to freeze when it encounters low temperatures. 2.Drain mouth freeze Each refrigerator will have a drain outlet, used to drain the frost water in the refrigerator, when this row of noisy ants water mouth to call for ice, the frost water can not be discharged, it will stay in the refrigerator, when they meet with the cold air will condense into ice.
3.Too much hot food in the refrigeratorMany people are accustomed to putting hot food or drinks directly into the refrigerator, and these hot foods and drinks will produce a lot of water vapor, which will naturally freeze when cold. 4.
Drinks spilled in the refrigeratorSometimes when the refrigerator is opened and closed, it is easy to accidentally knock over the drinks that have been opened in the refrigerator, and when the drinks flow into the refrigerator, it is very easy to condense into ice. Hope it helps.
Automation instrument refers to the use of industrial sites, the exercise of the process site working conditions of pressure, temperature, flow, weight and other detection and collection work, after automation systems such as DCS, PLC and other monitoring and processing, output corresponding, in line with the process requirements of the control algorithm, output scientific control signals to the control instrument (control valve or shut-off valve, etc.), and then adjust the flow, temperature, pressure, weight, etc. of the process medium, so that it can meet the high precision, high speed, and adapt to harsh working conditions of modern industry. Instruments and equipment that reduce labor intensity and improve industrial production efficiency are collectively referred to as automation instruments. >>>More
The hump is the main feature of the marshalling station, it is a small hill built on the ground like the shape of the back of a camel's hump, designed with an appropriate slope, the railway is laid on it, and the potential energy generated by the gravity of the vehicle and the slope of the hump is supplemented by the locomotive thrust to dismantle the train is a kind of shunting equipment, which is a main method of dismantling the train in the marshalling station. When carrying out the hump shunting operation, the train is pushed to the hump by the shunting machine first, and when the front car group (or vehicle) is close to the peak, lift the hook, then you can use the gravity of the vehicle itself, automatically slip down the slope to the predetermined line of the marshalling yard, so that the efficiency of the shunting operation can be greatly improved. The camel bee is generally located at the head of the shunting yard, which is suitable for the dismantling operation of the train. >>>More
There are three main employment directions for mechanical majors, namely engineering and technical personnel, design and development personnel, product sales personnel, etc. >>>More
Electric welding and gas welding are available, because it is automatic and mechanically welded, so it is not harmful to people's bodies.
Power system automation technology is now commonly used in engineering equipment this electrical automation control system, now many machinery and large electrical equipment will use such technical operation methods.