Why is the solar water heater not big enough?

Because you are buying non-pressure solar energy, which is the common overboard solar energy on the market, it relies on the pressure generated by the gravity of the water itself, so the pressure is small, and the water output is correspondingly smaller. Workaround:

1. Install a booster pump after the solar water pipe enters the home;

2 Smash the existing solar energy, install Samp's pressure-bearing automatic solar energy, and rely on the pressure of tap water to top out hot water (my is, it has been used for more than 5 years, the top layer, the hot water pressure is only slightly less than the tap water pressure, and the bath is like the pressure of the previous electric water heater). The disadvantages of this pressure solar energy: ** It is about twice as expensive as the overboard type.

If you can't release any water at all, it may be because there is no water in the solar energy, and the solar water heater controller is broken, just replace it.

The vacuum collector tube (glass) of the solar water heater is too thick because of the scale, the heat absorption performance is greatly reduced, replace the vacuum collector tube or ask a professional cleaning department to wash and descale all the vacuum collector tubes.

The water in the solar water tank has no pressure, and the water pressure and flow rate used are supplied by the natural pressure of the distance from the water tank to the indoor water pipe.

I'm going to give the upstairs not to charge If your house is newly pressed, it may be a problem with the production of the valve The flow of water is small, you can change 1 or 2 to try In fact, you can put the valve down and then turn the water on to see the flow rate of the pipeline to judge whether it is the reason for the valve or the reason for the pipeline If the hose may be folded in half, who can't come If it's hard, it may be a welding problem inside the pipeline, hehe, it's best to find an installation to solve it, they generally know Hehe, I hope it will help you, so the problem is generally not done The charge is generally not much.

Is your house on the top floor??? That's possible, the drop is not enough, the amount of water is small. Or the pipes are aging, and there are water shows and the like, which are not smooth.

1. The outlet pipeline is blocked.

The solar water heater produces small water, as we just said, which is the most intuitive judgment. This is due to the fact that the water in the solar water heater, the water quality is on the hard side, and scale is generated during the heating process, which adheres to the inner wall of the outlet pipe, the valve.

If the outlet pipe is partially blocked due to the shower and other locations, the pipe diameter will become smaller, and the water output will become smaller, and this situation will be continuous and the water flow will become smaller day by day. This phenomenon occurs in many solar water heaters with poor water quality during 1 or 2 years of use.

2. The air outlet of the solar water heater is blocked.

At the top or side of the water storage tank of the solar water heater, an air outlet for pressure relief and exhaust is generally set up to prevent the water in the solar water storage tank from bursting the water tank during the heating process. Although it is called an air outlet, it is used for air intake when we use water.

3. The outlet pipe is bent.

Some friends' solar water outlet pipe, the strength is not enough, usually when the water temperature is not high, there is no problem with the water throughput, but once the water temperature is too high, or the outdoor temperature is large, the pipe will be soft, if the fixation is not good, it will lead to sagging and bending, or deflated. This is especially the case when the water temperature is higher and the more pronounced it is. It is equivalent to a reduction in the diameter of the pipe, which will also lead to a small amount of water output.

Cause Analysis:

1. The vertical drop between the solar water tank and the bathroom shower head is too small;

2. Too many bends in the pipeline and thin pipes also affect the pressure of hot water;

3. The pipeline is blocked or the faucet filter is blocked.

Solution: 1. Use a small pressurized nozzle;

2. Change the mixing valve or add a thermostatic valve;

3. Rearrange the pipeline;

4. Appropriately increase the height of solar energy to improve the drop, or use the upper and lower water pipes with thick pipe diameter.

The water of the solar energy is flowing down by itself, the pressure is too small, if the hot water is less, it is the problem of solar drop, one is to add a booster pump, with a small booster nozzle will be better. If it is more than two years, first see if it is caused by scale in the shower (sprinkler), you can unscrew the shower to see if the water volume is still small, it may be caused by more scale in the mixing valve. The other is caused by limescale at the outlet of the water storage bucket.

The solution to the problem that the water output of the Yang energy water heater is too small].

Plan 1: Replace the sewer pipe, at least use 1418 pipes.

Scheme 2: Add a booster pump;

Plan 3: If the above 2 plans are useless, check whether the faucet has not been removed for a long time to clean up the dirt. Use a wrench to unscrew the water pan of the faucet.

The small water must have something to do with the small drop.

If you just use it, you can install a special solar booster pump, or you can change a booster nozzle;

If it becomes smaller after a period of use, it is necessary to consider whether there are impurities or scale blocking the water pipe or sprinkler head, and clean it up.

Install 1 x DN15 caliber booster pump and add 1 valve to the outlet of the booster pump. At that time, the hot and cold water can be adjusted by adjusting that valve is almost uniform.

1.Check the faucet: First check the faucet for blockage or scale, if so, you can clean it with vinegar or citric acid solution.

2.Check the water pipes: Check if the water pipes are blocked or bent, and if so, they can be replaced or repaired.

3.Check the water pump: If the solar water heater is equipped with a water pump, you can check if the water pump is working properly, and if not, it can be replaced or repaired.

4.Check the water tank: check whether the water tank has stagnant water or debris, and if there is a shot, you can clean the water tank with pure envy.

5.Check the solar collector: Check the solar collector for stagnant water or debris, and if so, clean the solar collector.

If none of the above methods can solve the problem, it is recommended to contact a professional solar water heater repairer for maintenance.

The solution to the solar water heater output is too small as follows:

Replace the mixing valve.

Replace the water tank. Replace the thermal probe.

Adjust the water inlet.

Replace the electric heating.

Replace the old pure denier tube with cold water.

Use a pressurizer.

The above is the solution to the solar water heater water heater is too small, I hope it can help you.

The solar water heater water is not satisfied with the water, it may be another reason, with the solution:

1. If the tap water pressure is insufficient, a check valve needs to be installed in the pipeline, and a fully automatic self-priming water pump can be installed.

2. If the upper and lower water pipes are leaking, the pipeline valves or joint fittings need to be replaced.

3. There are debris or aging cracks between the silicone ring and the inner tank; It is necessary to remove debris or change the silicone ring. If the silicone ring falls off or slides out, you need to adjust the tailstock or water tank to put on the silicone ring.

4. If the pipeline is frozen, it is necessary to thicken the insulation layer, and an antifreeze electric belt can be added.

1.Check if the water pipes are blocked: Check the water pipes for plugging stoves, and if so, you can use a pipe unclogging agent or cleaner to clean the water pipes to ensure that the water is flowing smoothly.

2.Check whether the water tank is leaking: check whether the water tank is leaking, if there is, you can make the liquid dismantle and seal the water tank with sealant to prevent water leakage.

3.Check whether the solar energy collector is damaged: check whether the solar collector is damaged, if it is damaged, you can replace it with a new solar collector to ensure the normal operation of the solar water heater.

4.Check whether the water tank is damaged: Check whether the water tank is damaged, if it is damaged, you can replace it with a new one to guarantee the normal operation of the solar water heater.

Check if the water pressure is not enough or if the inside needs to be cleaned.

<> the solar water heater is not satisfied with the water, it may be that the water pressure is not enough, or the water is full, and the solar display is faulty, you can check whether the water in the tank is full, and then the meter control is out of order, and the wrong signal is transmitted, and the sensor needs to be replaced.

This answer is applicable to most of the solar yard water heater models of the four seasons Muge, Sun Rain, Haier and other rough mold hail brands.

There are three reasons for the low water output of the water heater, the first is that the drop is too small, and the solar hot water hail device is generally not a pressure water heater. Because the amount of water produced by most solar water heaters depends on the size of the drop, if your drop is too small, it may be that her water flow will be smaller. In words like this, the blessing of living on the roof must have a very big feeling, so is there any solution?

Of course, there is, but the easiest way is to increase the height of the solar energy to increase the drop. Alternatively, you can choose a thick water supply and water pipe. If it doesn't work, you can add a booster pump directly.

Adding a guess shot booster pump is just a more convenient method, and it is sold on a certain treasure, which is very cheap. This is often the case at home. Reason number two.

It may be that your electrical lines are long and there are bends in the corners, so it will hinder the flow of hot water. In that case, the only way to do this is to rearrange the pipes. The third type is that there is a blockage at your inlet and outlet or somewhere in the pipeline