How to display the maximum value of the ordinate in origin

<>2. Create a new job ** for data input and processing.

3. Enter the data in the experimental process; Or bulk import.

4. Select all of them, and then draw them into a line chart.

Of course, it can also be drawn into other graphics.

5. Draw successful graphics.

6. Click on the analysis ---math --- integration --- above to open the pop-up box and process the data accurately.

7. In the pop-up interface, do not change any data, click OK.

8. The maximum value of the curve and the corresponding ordinate can be obtained, and the half-height and width can also be obtained.

or integral area.

Double-click the coordinate axis to set the maximum and minimum values in the dialog box.

Right-click on the axis and set the maximum and minimum values of the axis and the increment value in scale.

1. Open the Origin software, create a new workbook, and import data.

2. Select two columns A and B to label the dot line diagram.

3. Double-click the y-axis to pop up the property box.

4. Select Grid Lines to display all the properties of Grid Lines.

6. Finally, the coordinates of parallel grid lines and vertical grid lines are marked.

1.There are two columns of xy in the original data table, copy and paste column y, generate a new column, select the new column, right-click set as, select label, and the others can be plotted as before.

The value of the label item is displayed on the icon of each dot.

This displays the ordinate value for each point.

2.If you want to display both abscissa and ordinate.

Then press the xy data value by yourself, and then create a new column, such as x=2, y=5, then the new column is (2,5).

The same as above is defined as a label, and the diagram can be used.

Since the default font format of the new column is arial, garbled characters will be displayed, and you can double-click to change it to times new Roman after making the picture.

1. Open.

2. Put the light and silver mark of the mouse in any position on the x-axis rental banquet, double-click the mouse, and an option will come out.

3. Then modify the value after to, this is the maximum value, from is the minimum value, you set the maximum value and the minimum value according to the situation of your data.

4. The previous one was 10, but now Jane Hunger is adjusting it to 20, so it's okay.

5. After the adjustment, it is completed.

It's not a matter of adjusting the coordinates, you need to adjust the scale of the page, because the default page scale of origin is close to square.

You can right-click on the blank space outside the coordinate axis in the figure, [Note, it must be the blank space outside the coordinate axis in the figure, and the content of the dialog box popping up by right-clicking on the coordinate axis is different.] Then select Properties to pop up the Plot Details dialog box. As shown in the figure below:

Under Print Dimensions on the right, replace units with common units, such as cm, mm, etc., and then increase width to about twice the height, e.g. 20 for height and 40 for width. After clicking Apply below, you will see that the white on the underside has widened.

Then click "Field" in front of the graph on the left side of the plot details, open the tree structure, and click layer 1, as shown below

Select the Size Speed tab on the right, or replace units with commonly used units, such as cm, mm, etc., and then increase the width to about twice the height. After clicking Apply below, you will see that the abscissa has widened.

If the proportions are not yet harmonious, you can adjust them a little more.

Finally, click OK, and you're good to go.

How does origin automatically adjust the proportions of the horizontal and vertical axes? 1. Right-click on the blank space outside the coordinate axis in the figure, and then select Properties, and the Plot Details dialog box will pop up. As shown in the figure below:

Under print dimensions on the right, replace units with common units, such as cm, mm, etc., and increase width to twice height (e.g. 20 for height and 40 for width).

2. Then click "Field" in front of the graph on the left side of the plot details, open the tree structure, and click Layer 1, as shown below

First of all, it's not clear if you're talking about a dual y-axis coordinate graph, or just having the ordinates show on both sides of the graph.

The difference between the two is:

The double y-axis coordinate chart can realize that the left and right sides have different y-axis scales, indicating that two sets of data share the same x-axis.

If you just have the ordinate on both sides of the graph, then the scales of the two y-axes are the same, just to make it easier to view the data.

In addition, different versions of origin have different methods, I don't know whether you use a lower version, or a higher version, the higher the version, the more convenient the operation.

For example, for a double-y-axis coordinate graph, you can click plot —>multi-curve —>double y) on the origin menu bar, and the coordinate system of the double-y-axis coordinate graph is established.

For just letting the right side of the graph display the ordinate, the most basic principle of origin graphing is "what you want to modify, just double-click what", at this time you only need to double-click the coordinate axis, select the title & format tab in the pop-up dialog box, find the "right" ordinate on the left, click it, and then check show axis tick, and the right y axis will be displayed.

Double-click on the ordinate axis, find title&format in the dialog box, select the right axis in the selection on the left, and check showaxis&tick