-
Anonymous users2024-02-07The host owes a flat and hits him. - I have a little donkey that I never ride.
-
Anonymous users2024-02-06The computer console started and stopped when it rang and the solution:
1. Explain that the host is powered on, let's see if the host power supply light and hard disk light are on, if it is not lit, it means that there is power on but the voltage is not enough, so it may be that there is a problem with the host power supply, try to replace the power supply;
2. If the first step is normal, that is, the power supply and hard disk lights are on, the next step is to see if the display screen is displayed, if the display screen has been black, it means that the display screen is not powered on, check whether the display socket is loose.
3. After excluding the second step, look at the display screen display content, if only a few lines of words are displayed, it will stop, and it has not entered the system interface, there may be a problem with the memory, it is estimated that the memory module is loose, we will remove the memory and wipe the metal part with an eraser, and then install it back.
After the third step is eliminated, if it still can't be started, then look at the screen display, if there are "HDD controller failure" or "drive not ready error" These prompts indicate that there is a problem with the hard disk, maybe the hard disk interface is not in good contact, and you can reconnect the hard disk.
The above is my usual way of dealing with computer failures in my daily life, and generally not very old computers are caused by these reasons, which is very practical.
-
Anonymous users2024-02-05Is it a problem that happens while playing or is it a passing problem as soon as the device is turned on? The sound from the console is usually a hardware warning sound, and there can be a number of reasons for this.
1. The heat dissipation is not good, and the fan is most likely to be broken. In this case, it is recommended to deal with it immediately so as not to burn the hardware.
2. The voltage is unstable, try to see if it will be like this after a while.
3. Remove the main chassis and clean the dust, and reconnect the cable and card slot.
4 If it is a hardware problem, it must be checked, but if the computer is running normally, there is no problem with the hard disk, memory module, graphics card and CPU, and the possibility of hardware failure is very small.
-
Anonymous users2024-02-04It should be a hardware issue.
One. It may be that heat dissipation is not good.
Open the case and see if any fan is not rotating or is spinning very slowly, especially the CPU fan.
Two. It's the damage to the hardware、This may have to be replaced。
Three. This problem will occur when the computer has been used for a long time and the motherboard is aging.
Poisoning is unlikely.
If the temperature is too high, it will automatically shut down the protection.
That's your BIOS alarm tone.
First of all, you should be clear about what your motherboard's BIOS type is, you can check it by reading the manual or through the POST. >>>More
1. It may be a problem with the display itself, try to replace a monitor. Or connect it to another computer to see if it's normal. >>>More
Generally, there are several reasons for the automatic restart of the mobile phone, which can be self-checked. >>>More
There are very reasons for the black screen,One is caused by a virus,Try the full antivirus,The second is a system problem,Or there is a conflict between software and hardware,Reinstall the system can be solved,The third is the graphics card problem,The graphics card driver is wrong or the graphics card is broken or the graphics card is loose Clean up the dust of the chassis,Use a skin to wipe off the gold finger of the graphics card to see if it is magnetized,4 Hardware problems,For example, memory module CPU graphics card motherboard and other hardware,Whether there is looseness 5 Display problems The display is broken 6 The hardware acceleration settings are too high, beyond the frequency range 、 Click Windows Start Menu --Control Panel --Double-click the Show --- Troubleshooter tab, and under Hardware Acceleration, gradually drag the slider from Full to a position close to None-Click the OK button. 7BIOS settings are incorrect or overclocking is unsuccessful Black screen can be reset to the default value by discharging the motherboard 8 Black screen when opening the program, for example, games, one is that the graphics card does not meet the requirements of the game and is black, and the other is that it conflicts with the program, so it is black and crashes 9 I have a black screen plan in Microsoft It is recommended to reinstall the system.