i9000 data Internet why do you have to search the network every time?

Hello, System Settings - Wireless & Network - Mobile Network - Use Data Network, Leave the rest alone. Since mine is a Hong Kong cargo, you need to check Data Roaming ("R" appears on the right signal grid on the screen).

Hope it helps you, thank you.

1. Samsung i9000 MMS settings:

Application -- Settings -- Wireless & Networks -- Mobile Networks -- Mobile Networks -- Access Point Name:

Press the lower left menu key"Name of the new access point"

1.Name: China Mobile Mobile Internet access.

2.Access Point Name APN: CMWAP

3.**：4.Port: 80

5.Username: (empty).

6.Password: (empty).

7.Server: (empty).

Remember to add http: otherwise you can only send and not send - 9MMS**:

10.MMS port: 80

11.MMS Protocol: WAP is selected here

02 (Some machines need to set 00, the native Chinese version can only be set 02) 14Authentication Type: CHAP

15.Access Point Name Type: When you have finished typing (mms), press menu and select Save

2. Internet settings:

Application -- Settings -- Wireless & Networks -- Mobile Networks -- Mobile Networks -- Access Point Name:

Press the lower left menu key"Name of the new access point"

1.Name: cmnet

2.Access point name: cmnet

3.:(Empty).

4.Port: (empty).

5.Username: (empty).

6.Password: (empty).

7.Server: (empty).

9.MMS**:

10.MMS port:

11.MMS Protocol: WAP is selected here

02 (Some machines need to set 00, the native Chinese version can only be set 02) 14Authentication Type: CHAP

15.Access Point Name Type: (Internet) When you're done, press Menu and select Save

If the mobile signal icon shows R, just tick on Apps - Settings - Wireless & Networks - Mobile Networks - Mobile Networks - Data Roaming.

Is it used to move the latter 2G card? In some cases, you need to turn on roaming to use it.

There is no image, because the current monthly package is basically a national package.

The reason may be the Internet. After all, the i9000 is a parallel machine.

It is possible that the territory of the card is out-of-town.

My mobile phone began to have the above problems, available outside, wireless at home computer, but i9000 can not be connected, even if it is connected, it can't open the web page, and finally open the web page, and can only open a few!!

1. Configure your router.

Mine is tp-link.,Enter on **,Account name admin,Password admin (basically this is the case if you haven't changed)

First of all, it is necessary to determine - basic settings of wireless network - turn on the wireless function - selected, if you don't choose then you can choose it and try it, maybe it will be.

If you can't select it, then go to the DHCP server - static address assignment, click - view new entry--- enter MAC address, IP address, status selection - effective --- save.

Some people may ask: how to get a MAC address? --Phone Settings--Wireless & Network--WiFi Settings--Select the Mumu key (that is, the key other than the phone touch screen except for the home button and the back key)--Advanced--From which you can see the MAC address, the one on the phone is for example:

12, on the computer to ask for it":" Replace it with "—"It's good."

How do I get an IP address? --tp-link's DHCP server--DHCP service--View the address pool start and end addresses.

This way, you'll have a specific IP for your phone (and the other wireless computers in the room can do the same - no one else can steal your network).

2. Set up your phone.

Remember the one above? --Phone Settings--Wireless & Network--WiFi Settings--Select Mumu Key--Advanced Bar, IP Settings--Use Static IP, Set the following:

Network Mask: Domain Name 1 and Domain Name 2: On tp-link -- Network Parameters -- WAN Port Settings -- Advanced Settings below -- Here you can see the two servers that tp-link gives you, fill them in turn.

Click mumu -- save.

Once the above is done, reboot your phone and tp-link, and it should be fine.

If that doesn't work yet, then there's one last possibility: encryption!!

Don't think that your wireless network is not encrypted, and it will be better if you don't set a password, in fact, it's not, mine is at the end through the tp-link setup wizard, changed the encryption - it should be called added encryption - set the psk password before connecting, why is this!! I don't know why I don't know why I can't connect to the password, so I worked on the last step for a long time!!

There's something wrong with that system you're brushing.

Hello and welcome to the Samsung Digital Services platform.

It's a problem with you flashing the package, brush back the official package and try it.

EDGA, this mainly depends on the network environment, if there is a 3G network, the 3G data will be connected, and the 3G network will show that the 3G network is not good, and if there is no 3G network nearby, the 2G network data will naturally become E or G

If you are a native system ... Find the operator after selecting Wireless & Network... Select the node name and network standard!

Finally, open the data! Otherwise, you won't be able to get in! See for yourself.

Compare my methods! There will be options for you to choose from!