How to Use a Switch to Establish a LAN !! Play the game Red Alert Warcraft

If you're talking about a local one, it seems that you can use a router.

Everyone's network cable has to be connected to the router.

Then set up a LAN from the online neighbors.

Online Neighbors Set up your home or small network Next then count the middle one and the back one Select not to share The last one to restart if you want to restart.

If it's a long way off, let's go to the next Haofang.

Go in and choose the Frozen Throne or whatever, the Constituency room, and to start the game, you must be in a room with the IPX SPX protocol.

Local Connection Properties Protocol Select IPX SPX protocol to install (this protocol must be pressed regardless of short distance and long distance).

If there is a situation where you can't get in, it may be that the Windows built-in firewall does not turn off the local connection (it can also be a wireless connection according to yourself).

The property Advanced is turned off.

But after playing, it's best to turn on your own software firewall without turning it off.

If you can't see each other, it may be the version, or there is a game that is not installed, i.e. copied.

Uh-huh, well, that's all there should be.

I hope you can connect well.

The default gateway is So that your computer is the server of the local area network, remember, the IP address and the gateway must be the same, other computers only need the last bit of the IP, the others remain the same, such as: IP address: Subnet mask:

Default gateway: Remember: the gateway must be the same as the server's.

In this way, you are a local area network, and any game built on a computer can be played in it

Open the network neighbor, check the network connection, right-click the local connection properties, install ipx spx (there are a lot of letters at the back, anyway, it's the longest protocol), double-click the protocol after installation, and set the internal network number inside. The front is all zero, and the last digit is fine. Both computers need to be set up.

However, the last digit cannot be set the same.

Give it a try.

Warcraft can be connected directly, the red alert game serial number should be changed, and each one connected to the network must be different (if your game serial number is the same, then your red alert must be copied the same version), how to do it:

Find a file named " in your red alert folder, open it with "Notepad", and change the last two digits, which are different for each unit.

Change the last two digits "40" to a different one for each unit, and in the game options, select Network.

socket number - 0

Target network –

Firewall number – can be left unset.

Use a hub or switch to connect the computer with a network cable, and then set the IP address in a network segment.

In the case of a laptop, the two network ports are directly connected with a network cable.

If you want to use a desktop, you need to use a router.

Open Game - LAN - Create Game - Select Map - Create Game.

Pick your opponent to open If you build it, he can't see it, let him build you.

Your computer's IP subnet mask is all.

Your friend's IP subnet mask is all.

Critical Windows Firewall to be turned off. (or you won't see the new game) that's pretty much it's easy.

1.Connect all computers to the switch, configure the IP address on all computers (the value of x can be 2 254), and the subnet mask is all . 2.

Share the folder that needs to be shared, 3Allow Windows Firewall to let"File and printer sharing"The project was adopted.

Adjust the IP of the two machines, ?, the question mark represents two numbers, each one is different, and the two laptops can be directly connected with a network cable without a switch. Turn off the firewall!!

A small switch, set up the same network segment of the computer.

Sharing a router will do the trick.

Can't you use a router, do you have to use a switch?

Yes, a "direct connection" will solve the problem.

1. The two machines are equipped with network cards;

The network management is set to;

3. Buy one or make a "straight line", note that it is not a "cross line". **Approximately RMB meters.

If you do it yourself, you need tools such as crystal tongs.

T568B Orange White, Orange, Green White, Blue, Blue White, Green, Brown White, Brown T568a Green-White, Green, Orange-White, Blue, Blue-White, Orange, Brown-White, Brown If two computers are directly connected, then make one T568A and the other T568B Good luck!

Connect the two laptops directly with a single network cable, and here's what you need to do after that:

1. Online neighbor --- set up a home or small office network (left) - direct next step ---

Next – Select "This computer passes through the resident's gateway......"Next--- Next -- Workgroup "mshome" -- Next: Enable Sharing --- Next --- Complete the wizard, I don't need to ......

After the network cable is connected, each machine does this once, and then restarts, it should be noted that the working group needs to fill in the same name.

In fact, there is no need for cross-wires, since it is a notebook, of course, it is more convenient to use wireless. The landlord can buy a wireless router on the face of the death, about 100 yuan, connect the router with the cat that telecommunications or Netcom sent to you, and then 2 notebooks are connected to this router, without any settings is a local area network, 1 builder, the other 1 can be seen. This one is very convenient, and there is also a manual for router installation.

It's a completely fool-level operation.

It's to buy a network cable, one end with 568a wire, and the other end with 568b.

On the line, you can also use a wireless network card to connect your book does not have a wireless network card?

Yes. I want to keep up with the bounce network cable. Tell them directly to make a rebound and they will do it for youAny place where the network cable is clamped will be done. Then set the IP.

There is a kind of computer cable that is used online for multiple computers The advantage is that you can connect with other computers without Internet access There are sales of Dalian **150 yuan (3 online) The line is not long and the computer needs to be very close This method is easy to use My brother is to take the notebook to my house to play.

It's very simple Buy a router, plug it in and you can connect it directly

If it's a pure network cable, it's like the method upstairs, you just tell the person who sells the network cable

You don't need to do crossovers anymore! Because it's all adaptive now! Set the IP and you're good to go! Unified to 568B line sequence!

A normal Internet cable solves the problem I played with my classmates in the dormitory (CS Warcraft) but I have to change the IP to automatic.

Buy a router and install it, it's very simple.

It's very convenient to buy a router for 60 yuan.

If it's a notebook, don't do anything: it's very simple, choose a machine as the host, in the wireless network connection - point attribute - select wireless network configuration - point add: create a wireless network, write the network name and don't change the other, it's best to set the key 10 digits - click OK - go back to the wireless network configuration - point advanced - select only computer to computer, and then OK, OK.

Then you click on the Wi-Fi connection - check the Wi-Fi network to find the network you just created, connect to the network, and the password is the 10-digit number you set. All the other devices need to do is connect to your new network. Note that all machines must turn off the Windows Firewall, otherwise it will be useless.

Okay, here's my way, it works, you try it.

Buy a router, or buy a switch, and if you have an Internet connection, set the IP to get it automatically. If you don't have an internet connection, set the IP to.

(Remember to turn off the firewall).

Just buy a router, and it's very convenient to buy a wireless router in this book. My dorm is to use these few people to fight the Age of Empires together.

Add the ipx spx protocol to the network protocol of all machines, and after entering the game, use the third item of the network, and after setting up a host, the other machines will join and start after they are ready.

Then you only use Haofang QQ and other battle platforms to connect together, enter the same room together, that is, you can play, and you can also get points on the platform, hehe.

Why don't you use a router, it's easier to use a router, just connect to it and set an IP.

Second PC Setup:

Third Computer Setup:

By analogy, if it is an online game, the host should turn off the firewall that comes with the system.

Based on what you think, I think you're using a normal switch.

Quite simply, all machines are on the same network.

IP is PC and so on. Keep it going.

It is to determine whether you want to use the gateway for Internet access in the future, you can use it or not

If you want to be in a LAN, the basic condition is that two PCs are in the same network segment, if you two computers use the same switch or router, then you should be able to play LAN games.