The EPSON Stylus COLOR300 printer prints with the cartridge stuck on the right side and does not mov

Hello, the printer is color3000 bar, a large format printer,

Go to the Internet to find an R230 clearing software to try to reset the chip.

I used to have this printer, repaired and repaired, it really troubled me a lot, one day on the street to see, the new printer is only 200-300 yuan, including black and white heads and color heads, what else to repair, immediately bought one (I bought canon ip1600), the effect is much better than epson. Overall, the printing effect of Epson is not as good as that of Canon!! You look at the Canon IP1180

XP comes with it.

Click Start -- Settings -- Control Panel --- Printers & Fax -- Add Printer -- Manufacturer Select Epson --- Find it in the model.

We are very sorry that the product you consulted is not available in Chinese mainland, and we cannot provide you with a detailed solution. You can find information about this product by browsing the following Epson Global**:

In this case, the ribbon is usually faulty

1. The driving belt of the ribbon driving wheel is worn or broken.

This failure is caused by the drive belt being used for too long or the character chain rubbing against the drive band. The solution is to adjust the position of the character chain so that it no longer rubs the drive band; If it is broken, please replace it.

2. The ribbon motion sensing signal is interrupted.

First, check whether the ribbon motion sensing signal cable has been damaged, and replace the signal cable if it is broken; Then check whether the ribbon motion sensing signal cable at the J6 socket on the interlock conversion board is damaged or not in good contact, please replace or plug in the signal cable.

3. The Hall effector is damaged.

Frequent cassettes and Hall effectors are constantly squeezed, which in turn causes damage and breakage. This fault can only be replaced by the ribbon swivel arm assembly or with a ribbon motion sensor.

4. The ribbon is stuck.

The edge of the ribbon is easy to entangle the ribbon wheel after detachment and fluffing, resulting in the ribbon wheel being stuck, and the ribbon cannot be retracted into the ribbon box normally. The solution is: first open the printer cover, open the ribbon arm and the hammer row interlocking handle, gently pull the ribbon back at the tape feeding end of the ribbon box, then close the ribbon arm and the hammer row interlocking handle, turn on the power, and the ribbon will be loaded back into the ribbon box after the machine self-test.

Let me answer, there are generally two situations when printing blank pages, one is that the print head is burned, one is the F1 resistance on the motherboard is burned, or there are two row tubes This is the printing blank page, if there is a little ink on the paper, the above problems do not exist.

Press the button on the printer, let the printer print a test page offline, see if the printing effect is normal, generally shut down, and then press and hold the paper feed to build the machine, and then release the paper feed to build, to see the printing effect, generally 80% of the blank page is not repaired, and the print head is not guaranteed Good luck

Try it out with the printer's test function.

If not, run the cleaning sprinkler function.

If it doesn't work again, I have to send it for repair!!

What kind of cartridge did you change? There is a problem with the ink cartridge, so it cannot be recognized by the printer.

Did you change it yourself, are you sure the steps are correct? To change the ink cartridge, you need to remove the small sticker on it, and if you forget it, it will be blank printed, and many unfamiliar or the first time you replace the ink cartridge is like this. If you can print normally before changing the ink cartridge, this is basically this problem, and then it is possible that the ink cartridge is not original and you can buy a bad ink cartridge, and other problems are unlikely.

For example, the printhead is broken and the motherboard is hanging, which is relatively rare.

Select "Start" - Settings - "Devices and Printers" or "Printers & Fax", right-click the printer icon, and select "Printing Preferences" - "Maintenance" or "Application Tools";

Select Nozzle Check, select Print as prompted on the screen, and the printer will print out the nozzle check sample.

If the nozzle inspection is also spent, you need to contact the Epson authorized service in the pure heart to carry out professional maintenance of the printer, you can browse the following ** to view the nearest service center.

Clean the printer printhead.

Tell me your email address. Sent to you.