Spartacus motherboard crossover options, where are the overclocking options in the BI 800 motherboar

I'm using a BA-270, so the options should be the same, so I'll give you a reference.

This board does not have a crossover coefficient adjustment, only the memory frequency can be adjusted to change the crossover factor.

1. First change the Power User Overclock Settings - Memory Clock Mode option to Manual (manual).

2. After the change, there will be an additional memclock value below to adjust the memory frequency, it is recommended to reduce it to 533.

In order to ensure that the overclocking amplitude is increased, the HT and NB (northbridge) frequencies can be reduced.

The HT frequency can be adjusted in the Link Speed option, and it is recommended that the HT frequency is guaranteed to be below 2000MHz after overclocking.

The NB frequency can be adjusted in the CPU-NB FID option, and the NB frequency is guaranteed to be below 2000MHz after overclocking.

HT frequency = external frequency XHT coefficient.

NB frequency = XNB coefficient of the outer frequency.

External frequency: Actual memory frequency = crossover factor.

If your English is better, look at the motherboard manual is the best, you can learn by yourself, if not, you can look at the Chinese character description above, the same can be set, the memory is generally overvoltage, if not, it's better not to move, it's easy to burn memory, your board is over 3G, it's OK, not in Hua Ge's better board.

Overclock is the overclocking tab. Among them, CPU configuration is the processor to adjust the memory configuration is the memory timing adjustment OC voltage control is the voltage setting, and also pay attention to the CPU configuration in the Advanced tab, if you want UHF, you need to turn on the CPU C6 report option, otherwise at most.

Question added: I don't want to disassemble the chassis, the design of the motherboard should have considered how to remove the password, I know that the password enters the BIOS system. On the right side of the screen there is the option to set a password. Select this item and press enter twice. Confirm.

Do you still need to set it up on the BIOS? If it doesn't work, go to the place where you bought the computer and take a look, don't fool around, it's not cost-effective to break it.

Not every CPU can open the core, it has to do with quality, and the shielded cores are more or less problematic, don't think about opening the core, it doesn't make sense. Most of them are gimmicks by sellers.

I bought a core open-core x2 220 on National Day.,It's only been more than 1 month to open a quad-core.,It's not good.,The blue screen can't get in when the core is turned on.,Hardware unknown error.。 Hehe,The people in the computer city explained,That's it.,How long can the core state be used depends on luck.,After all, the other 2 cores that came out were blocked by AMD manufacturers who thought there was a problem and were unstable.。 Haha, I had to discount it by 220 yuan, and then pay 730 yuan for a real quad-core CPU X4 955.

It is recommended that you also trade this open-core CPU for a real quad-core. It has a depreciation fee, and the longer it is delayed, the lower the price of the reversal. There is also a 3-month replacement period.

In fact, there is not much problem with temperature control, and this temperature is normal, and most of the original fans are like this. In fact, there is no need to worry about problems, as long as the temperature of the CPU does not rise all the time, 1500 rpm is completely sufficient, if the temperature continues to rise, the motherboard will generally continue to increase the speed until full speed.

The rest is the same as the upstairs.

There are just a few options for CMOS movie management. What is the maximum and minimum speed, and others, you should set the default standby speed to the maximum, that is. If none of that can be solved. You just have to change the fan, good luck.

Which model of Spartacus board are you using, not all boards support AHCI.

Your laptop problem, diskgen partition table repair is to format the entire hard drive, because what you said when you detected it prompted that the hard drive was not recognized. I only used diskgen to repair the partition table and look at it.,What about things.,There's no way to save it.。 However, you can use a CD-ROM or USB flash drive to use the PE system to see if you can view it, copy everything you need, and then repair the hard drive.

Once it's repaired, repartition the hard drive and then redo the system. Your Spartak motherboard,I rarely come into contact with it.,So I don't know much about it.,The way the hard disk mode is changed.,The options are basically in that sata or something.。 Hey!

Hard disk mode change is basically only used for laptops, are you a notebook?

Does the motherboard support AHCI, have you used it before? Mine is particularly easy to find, but it's not your bios

If you find the option with boot in the BIOS, you should be in the advanced BIOS settings.

Then change the first boot down.

Motherboard BISS is developed by each motherboard manufacturer. Each model is different.