How to spray paint the vintage wood grain of multi layer solid wood flooring 5

1. First of all, use an angle grinder to polish the iron door, and knock off the rust or old patent leather on it;

2. Then start to mix the paint, because the paint will precipitate, shake it well before opening, pour it into a clean container after opening, add one-third of the thinner, stir well and use;

3. Connect the air pump and the watering can with a gas line, power on after connecting, and use it after the air pump is full, pour the adjusted paint into the watering can, tighten the cover, aim at the door, hold the handle, and you can spray;

4. In the spraying process, the watering can should be gently rocked from side to side, sprayed evenly, the watering can should be kept at about 20 cm from the door, sprayed at least twice, and the interval between the two hours should not be less than two hours;

5. After the spraying is completed, the watering can should be cleaned with thinner.

This is the rubbing process, and the method is as follows:

The substrate is sealed first. To use a very thin wood oil to do a seal, then sand, and then brush a very thin wood oil, (after the wood is dry, it is better not to block the pores) You can also try it with a 3-4 times diluted primer! After the second closure, lightly grind with sandpaper of 600 wood.

Then it's time to wipe the color. The oil is diluted with kerosene, and then + talcum powder or calcium carbonate (to increase the viscosity and better fill the pores, there are also rubbing color treasures on the market, similar to jelly) After wiping in circles, wipe it with a clean rag, leaving only the capillaries, so that the three-dimensional sense of wood grain comes out. After that, if you use camel oil, then the primer must be sprayed, otherwise the thinner of the paint can dissolve the oil, and the color will be spent in a brush.

If you want to use spray paint, after you finish this, the following process is as you spray or brush. The effect of spraying is good, and the brush saves paint.

Dyeing and lacquering, the wood grain is the wood grain of the log

Wansong flooring***, excellent service, welcome to buy.

Hand scraped, hand-carved, or machine-drawn.

The solid wood skin itself is a natural wood grain and cannot be the same. There are two common types: mountain pattern and straight grain.

Solid wood flooring has more stable performance and less harmful substances **High solid wood parquet is bonded with multiple layers of solid wood, and the surface veneer laminate flooring is made of MDF as the base material, and the surface is pasted with wood grain paper.

Hope it helps.

Before painting, you need to sand, the steps are as follows: (1) Remove the garbage and debris on the floor. (2) First coarse grinding, then medium grinding, and finally fine grinding twice.

The floor feels smooth and flat after grinding, and should not have a wavy shape, otherwise it must be re-grinded. Solid wood floor painting process: (1) After grinding, remove the dust on the indoor ceiling, wall, window sill, floor, etc.

2) Apply primer. The lacquer should be a little thinner in order to penetrate into the understory of the wood. (3) Batch embedded putty.

If the quality of the floor is high, putty should not be embedded as much as possible. (4) Sandpaper. The place where the putty is embedded should be smoothed and cleaned.

5) Brush with paint. After the putty is dry, the paint should be evenly coated, there should be no overlap, and each brush should be long. (6) Second degree of paint.

After the first paint is dry, it is sanded with No. 400-600 water sandpaper, and then cleaned up, and then cleaned again. The third degree of painting and the fourth degree of painting are carried out according to this. No matter what brand of paint is used, the surface of the paint film is dry and the inner layer is not dry within 3 days, and you cannot walk on the paint film, otherwise the strength of the paint film and the bond between the paint film and the floor will be affected.

The primary color solid wood floor color can be painted, and the adhesion effect of the paint is better after polishing before painting.

Solid wood flooring is a floor decoration material formed by drying and processing natural wood. Also known as log flooring, it is a floor that is directly processed from solid wood. It has the texture of natural growth of wood, is a poor conductor of heat, can play the role of warm in winter and cool in summer, comfortable feet, safe to use, is an ideal material for floor decoration such as bedrooms, living rooms, and study rooms.

The decorative style of solid wood is back to the basics, the texture is natural, and the solid wood floor is more precious in today's declining forest coverage rate and vigorously advocating environmental protection. According to May 1, 2002, the implementation of the national standard GB T15306-2001 for solid wood flooring will divide the grades of solid wood flooring into: color palette, natural color board, grade B board, and excellent solid wood flooring.

It presents a natural log texture and color pattern, giving people a natural, soft, affinity texture, and because of its warm winter and cool summer, good touch characteristics make it an ideal material for bedroom, living room, study and other ground decoration.

You'd better remove the floor and paint it all down.

Clean the floor first, first coarsely grind once, and finally finely grind the floor twice after sanding the floor to the touch, smooth and flat.

Spray a layer of ordinary PU primer first, and then refine the color with color, if you don't deepen the color of the wood grain, it won't look too good, repair the color, and then use steel wool to gently polish it again, polish off the particles and wool on it, and then spray the primer.

The primer is best to use PE crystal transparent primer, so the hardness will be better, and then polish it after 4 hours after spraying, and then polish the wood thorn particles, and then polish the surface to be smooth, and then spray PU crystal transparent varnish 3 light is good.

The primary color solid wood floor you are talking about, is it plain wood? It's just not painted? If it is plain wood, it is much better and more expensive than lacquered board, and it is a pity that you paint on it?

Plain wood boards, if they are only a little dirty, can be cleaned with an abrasive and they will look brand new.

I personally do not support you in painting on plain wood boards.

If you must brush, you need to ask a professional to do it. The specific operation method, "purity design performance" is written correctly.

It is recommended that the landlord chooses special polyester paint for the floor, such as Laiwei paint, China Resources paint and giraffe have special floor paint, how long it takes can only be said according to your use, and the general family is no problem with the year!

Added upstairs . Hardwood floors have to be repainted after 5 years. Otherwise, the color will not look good. I don't know how you're going to do it. I don't think you will be able to touch up the paint in 5 years.

Solid wood doors are essential in modern home renovation. The solid wood door decoration is more elegant and solemn. For how to spray the solid wood door, many friends who have just started from the fact of wooden door processing do not know much, compared with other painted workpieces, the solid wood door painting requirements are higher.

Here is a brief introduction to the painting process of solid wood doors:

1. White embryo treatment, first plug nail holes, cracks, collapses, culverts and other defects with water-based putty, generally use wood color water ash, and also have their own deployment and use, the principle is that the color must be the same as the natural color of wood;

2. Use 150 mesh wood sandpaper to polish and smooth it comprehensively;

3. Brush the closed primer again; It can also be replaced with a clear primer;

sandpaper sanding;

5. For the wood with large bristles, you can first rub the color paste, and for the wood with small bristles such as pine, you don't need to rub the color, and the color rubbing is relative to the characteristic process requirements.

6. Continuously brush 5-7 times of transparent primer, subject to filling the bristles, wood with large bristles such as ash and other expensive paints are not recommended to be sprayed, and the interval between brushes is not less than 4 hours;

7. Repair the transparent putty and repair the defects that were leaked last time;

8. Polishing with 180 mesh dry sandpaper, then grinding with 240 mesh and 320 mesh, and finally grinding and polishing with 600 mesh or elastic silk cloth;

9. Thoroughly remove dust and clean the environment;

10. Spray the colored transparent topcoat for the first time, and polish the small particles of gara with 1000 mesh sandpaper after drying;

11. Then spray 2-3 times of color paint, and lightly grind the particles after drying;

12. The nozzle is semi-matte transparent topcoat, and the prickly heat is polished after drying;

13. Spray 2-3 times of transparent topcoat, and the acceptance is completed.

Solid wood door painting method:

1. Base treatment: cleaning, nailing, degreasing, scraping the soil, do not scrape out the wood wool and prevent the plastering surface layer from being scratched; Sandpaper, first grind the line angle and then grind the four-mouth plane, polish along the water pattern, tear off the small live warped skin with a knife, and use a small nail to hit the heavy skin firmly; Spot paint tablets, on the water knots and oil stains, point and brush with alcohol paint chips.

2. Brush the base oil: First of all, apply the oil again: start from the left side of the upper part of the frame and paint along the wood grain, and the oil on the edge of the frame shall not touch the wall, the thickness should be uniform, and the upper part of the frame is just right.

When brushing the door, first brush the door frame and then brush the door leaf, after the back of the door leaf is brushed, fix the door leaf with a wooden wedge, and finally brush the front of the door leaf. After all the brushing is done, check for any omissions, and wipe off the paint stained on the small hardware and other places.

Secondly putty: water-resistant putty and paint press 1: to configure putty.

Wait until the clear oil is dry. Nail holes, cracks, knots and edge defects should be scraped and smoothed with paint putty, and the putty should be wiped horizontally and vertically, and the putty should be scraped into the nail holes or cracks. If the seam or crack is wide and the hole is large, the putty can be squeezed into the crack with a knife, so that the putty is scraped flat and cleaned after embedding, and the putty on the surface should be scraped clean, and there is no wild putty and residue.

The upper and lower heads, tenons, etc. should be wiped.

3. Sandpaper: After the putty is dry, use No. 1 sandpaper to polish, the grinding method is the same as the bottom sandpaper, be careful not to grind through the oil film and protect the edges and corners, and leave no traces of wild putty. After grinding, it should be cleaned and the grinding powder should be wiped clean with a damp cloth.

4. Spray paint, spray three to four times.

I hope it can help you to find the painting process of the solid wood door: 1. Detect whether the wooden door meets the requirements, and the moisture content should be coordinated with the local climate.

2. Use sandpaper to remove burrs, wood thorns and other debris.

3. Paint it with a sealing primer.

4. Further remove burrs and wood thorns after drying.

5. Use putty such as putty to scrape and polish, which generally requires two to three layers (open can avoid this step).

6. Paint the white primer 2-3 times (open painting can be done once) 7. Further polish and repair the defective parts with putty.

8. Paint the topcoat two to 3 times, and the last time you need to polish it for the last time.

The method of spraying wooden doors is as follows.

1. Detect whether the wooden door is made to meet the requirements, and the moisture content should be coordinated with the local climate;

2. Use sandpaper to remove burrs, wood thorns and other debris.

3. Paint it with a sealing primer.

4. Further remove burrs and wood thorns after drying.

5. Use putty such as putty to scrape and polish, which generally requires two to three layers (open can avoid this step).

6. Paint the white primer 2-3 times (open painting can be done once);

7. Further polish and repair the defective parts with putty;

8. Paint the topcoat two to three times, and the last time you need to polish it before the last one;

9. Survival, if necessary, polishing process can also be carried out.

The advantage of general solid wood particle board is that the amount of adhesive is very small, which means that its environmental protection is very good, it is compared with the real solid wood board, the board surface is wide, the appearance is smooth and smooth, there are no knots, insect eyes and anisotropy and other shortcomings, no warping, no cracking, high physical and mechanical strength, longitudinal and transverse strength, sound insulation, mildew prevention, economy, heat preservation, etc. However, when it comes to wardrobes, multi-layer solid wood boards are better, because the area of multi-layer board bonding is less than that of solid wood particle board, and its environmental protection level can reach E1.

1 All that texture you can go to the decoration shop or carpentry shop to buy texture stickers, subsidize back, and then spray transparent paint on the line, it is recommended to do baking paint, the effect will be much better, but the quality of the wood grain stickers is also relatively high, otherwise the stickers will be baked when baking paint, so it is recommended that you hand it over to professionals, don't come yourself.

Has the original paint come off? If you don't take it off, you can just re-paint it, if you take it off, see if your texture has a piece of veneer to take off together, if it is your table, you have to re-apply the veneer in the spray paint.

The solid wood table should not be color-blocked, and it cannot be integrated into one, so it can only be polished off a layer of paint as a whole. But are you really solid wood? Solid wood will only turn black if it is hot, and it will not turn white, and the film will turn white.

As long as you have a multi-layer floor, it is best to be a national brand, there will be no problem with branded flooring, as long as the color is good-looking.

Icon flooring and Fillinger flooring in Shanghai; Del flooring in Jiangsu; Cicero flooring in Hunan; the natural flooring of Guangdong; Shengda flooring in Sichuan; There are also forest stars in Zhejiang, and the solid wood multi-layer flooring is very good.

Multi-layer solid wood is just a concept, it is recommended that you use solid wood directly or if it is cheap, it is composite. Multi-layer solid wood is only a bark layer of about 2mm on the surface, which contains more glue and is easy to crack, not environmentally friendly and deformed.

Looking for after-sales service, why do you have to get it yourself, go to the home 100 and ask them, they know more.

Buy wood grain stickers and find someone to paste them, and a certain treasure will be sold.