-
Anonymous users2024-02-11How to use the interface agent.
The use of the part of the filler ratio of the method of glue consumption.
Connecting the old and the new in the base plastering.
Glue: 1 cement: 0-1 Coating method: (plastering while wet):
Use a brush to evenly apply the prepared treatment agent to the surface of the base layer.
While it is not dry, it will immediately be plastered with cement mortar or concrete.
During summer construction, if the surface of the treatment agent dries too quickly, the base layer can be impregnated with water, and then the treatment agent is applied.
Glue: Water: Cement:
Yellow sand: 2 Use a brush to evenly apply the prepared treatment agent to the surface of the base layer.
Immediately plaster cement mortar or beat concrete while it is still dry.
In summer construction, if the surface dries too quickly after the treatment agent is applied, the base layer can be soaked with water, and then the treatment agent kg m2 can be applied
Brick slabs are laid. Brushing method: (plastering after drying).
Mortar in proportion.
Use brushes, brooms and other tools to brush on the concrete base layer, draw the hair into a rough surface, and then plaster after hardening.
In case of formwork and steel bar barriers, this method can be used for new and old connections.
Mixing method: bricks, granite and other brick slabs can be directly paved with diluted 302 mixed with cement fine mortar.
When directly paving new bricks on the old bricks or painted walls, first according to the above "brushing method", there shall be no loose hollowing and peeling on the old bricks or painted walls.
to bind the layer 3mm
Surface protection, waterproof and moisture-proof treatment Glue: 1
Cement: 1-2
Fine sand: 1-2 Prepare a thin or thick slurry, evenly brush on the clean base layer, the first with a thin slurry, the first.
The second and third passes are covered with thick slurry, and the two are brushed for protection and moisture-proof, and the waterproof and moisture-proof needs to be brushed two to three times, with an interval of more than four hours between each pass (after the last one is dry). Per dose.
Sand ground treatment.
Glue: 1 cement: 1-2
Fine sand: 1-2 Remove the loose ash that has fallen off the ground, brush it with glue first, then prepare mortar to scrape the painted sand floor once or twice, sprinkle cement and calender the amount of about each time.
-
Anonymous users2024-02-10Yes, glue guns. The glue seller will give it to you.
-
Anonymous users2024-02-09Summary. Kiss. Hello.
What glue is used to paste exterior wall tiles Exterior wall tiles can use special adhesives, generally referring to tile adhesive. It is mainly made of high-quality quartz sand and cement, which has the advantages of convenient construction, simple operation, high adhesion, low shrinkage, green environmental protection and no pollution, etc., which can effectively avoid the phenomenon of hollowing after tile pasting.
Kiss. Hello. What glue is used to paste exterior wall tiles Exterior wall tiles can use special adhesives, generally referring to tile adhesive.
It is mainly made of high-quality quartz sand and cement, which has the advantages of convenient construction, simple operation, high viscosity, low shrinkage, green environmental protection and no pollution, etc., which can effectively avoid the phenomenon of hollowing after tile pasting.
Precautions: 1. The temperature of the construction environment should be 5 35 °C. 2. Construction is not recommended in rainy and snowy weather.
3. Avoid rain within 24 hours after construction. 4. To design the expansion joint of the special return mountain gate, it is necessary to set up an additional separator next to the leakage, and the separator needs to be laid out according to the way of 1000*2000 or 2000*2000.
<> special mold for cast copper cast iron is not silicone, silicone is only one of the processes, the process is as follows: first of all, there must be a model (also known as a prototype), the model is surrounded by cardboard, poured with the prepared silicone, after the silicone is cured, open the silicone, take out the model, and then seal the silicone, fill with wax (the wax has hollow and solid, the hollow is closed on both sides, and is repaired with a soldering iron), and the repaired wax is added to the model tree (the model tree is the feed port, into a tree, In this way, a model tree can hang several wax tables, and several products can come out at the same time), put the finished model tree into a steel cup, pour gypsum into it, and after the gypsum is cured, put the gypsum into the oven, melt the wax table, and put the gypsum sample into the prepared vacuum box after the wax table is dissolved, and the mouth is facing up, at this time, we should pay attention to the temperature of the gypsum, whether the product is good or bad is directly linked to the temperature of the gypsum, pour the copper or molten iron in the furnace into the gypsum sample, and wait for the gypsum to cool down and break the gypsum. The inside is what the product looks like, whether it is copper or iron, the process is the same, this is a simple method of small batch processing, if it is produced in large quantities, it can only be made into a mold (die casting mold to produce, which can save costs).
Hello, is the sewage operated on time, check if the dental comprehensive ** machine is leaking? >>>More
Yes, it is for anchoring, not nailing! Flat roofs are generally not required to nail insulation nails on the roof of the roof. >>>More
OPPO mobile phone belongs to the Android machine, you look at your mobile phone system is Android, or based on Android, and then you look at what system the Bluetooth gamepad supports. If it is written above Android, and your OPPO phone is Android, it will definitely be fine. However, some gamepads need to be cracked.,That is, the phone can only be used after being rooted.,You can ask the store before you buy it's the best.,I hope it can help you.。
The external wall insulation of rural self-built houses refers to the thermal insulation treatment on the external wall surface of the building to achieve the purpose of energy conservation and emission reduction, warmth and heat insulation. >>>More