Air compressor air drying problem, why is the air compressor outlet pressure high and the dryer outl

Our company is not good at this, our air compressor manufacturer is the production and sales of screw machines, and the ones are made of extra high brands. You can check it out! Their name is Huitong Electromechanical Equipment****.

First, it's possible that your dryer doesn't have enough capacity. Clause.

2. The water of the gas tank must be discharged more than 3 times a day, and the number of times should be increased appropriately according to the different environments of each region. In addition, if the dryer is a refrigeration dryer, the air drying treatment effect is relatively much worse, and you can consider adding an adsorption dryer.

Mainly check the air compressor, Jiangmen Xinhui Shangyou electromechanical.

The equipment used for drying operations vaporizes and escapes the wet content (generally referring to moisture or other volatile liquid components) in the material through heating to obtain a solid material with a specified moisture content. The purpose of drying is to meet the needs of material use or further processing. For example, the drying of wood before making wood molds and wood can prevent the deformation of products, and the drying of ceramic blanks before calcination can prevent cracking of finished products.

In addition, the dried material is also convenient for transportation and storage, such as drying the harvested grain to below a certain wet content to prevent mildew.

Check the dryer, filter, and air tank for drainage.

In addition, there is oil, which may be that the air compressor is running out of oil.

A small amount of water and oil is easy to solve when buying Atlas. Copco air compressor machine is equipped with original automatic drain Its unique effect is unmatched by any other brand of air compressor. Greatly reduce the cost of post-processing equipment and improve the service life of pneumatic components.

Atlas. Wang Jun, Sales Engineer of Copco Compression Technology Department.

lff409 That's pretty much it, give points.

There is a screw on the bottom of the gas tank to drain the water.

Loaded with several oil-water separation.

In two cases, one is pipe back pressure.

high, the other is the high pressure of the press.

1. The higher the exhaust pressure, that is, the higher the pressure in the pipe network, the higher the back pressure of the compressor exhaust, which means that the compressor must consume more work in order to overcome this pressure and continue to exhaust.

The direct reaction is that the current of the compressor increases, and even if the amount of gas produced does not decrease, the power consumed per unit of gas production also increases, and the energy consumption decreases. In fact, it is a bit similar to the suffocation pump of a water pump, with a decrease in displacement and an increase in current.

Second, there are special point control means of compressors, such as similar to the minimum pressure valve blind trap and other things, only the pressure of the output of compressed air exceeds the set pressure of the valve can push it to exhaust, then your pressure setting is high, will naturally produce the situation described above, resulting in a decrease in gas production, a rise in current, and an increase in energy consumption.

Check whether the inside of the refrigeration dryer is iced and whether the inlet or outlet valves of the refrigeration dryer are not fully opened. There are many factors that need to be carefully investigated.

Hello, the desiccant filled with the equipment is molecular sieve and activated alumina.

1. Considering that the equipment has been used for a long time and the desiccant has been pulverized, the molecular sieve should be replaced.

2. The tank is not completely filled, and there is a gap between the molecular sieves. Under the impact of air pressure, the molecular sieves collide with each other and appear pulverized, so they should be stopped for inspection and refilled tightly.

3. The quality of the molecular sieve does not meet the requirements, the temperature difference in the tank and the air pressure impact, the molecular sieve is pulverized and cracked, and the high-quality molecular sieve should be completely replaced to prevent dust from polluting the gas equipment.

The air output of the air compressor is a lot of water. Is the dryer not broken.

The gas output of the air compressor contains water vapor, which usually needs to be dried to achieve a dry state. If there is still a lot of water in the output gas, there are generally the following possibilities:1

Dryer damage: The dryer may have been damaged and cannot effectively remove water vapor from the gas. The condition of the dryer needs to be checked to see if it needs to be replaced or repaired.

2.Improper maintenance: The dryer requires regular maintenance, such as replacing the desiccant, etc.

If not properly maintained, it can also result in a large amount of water vapor still being present in the output gas. 3.Air Handling System Line Leakage:

If there is a leak in the pipeline, the air will cool as it flows through the pipeline, resulting in the formation of vapor vapor. It is necessary to check the pipeline for leaks and repair them in time. 4.

Air compressor quality problem: If there is a problem with the quality of the air compressor itself, it may cause the output gas to contain more water vapor. It is necessary to check the status of the empty standby press and repair or replace it in time.

Summary. The air compressor dryer exhaust is airtight.

1. If the air pressure reaches the maximum, the dryer will be exhausted, which is the reason for the external pressure discharge.

2. After the air pressure is enough, the pressure relief valve on the dryer is opened, the air compressor is basically in a no-load state, and after the car is started, the dryer should be discharged from the bottom once in a while, and there will be water discharged.

3. If the air pressure is lower than the maximum air pressure, it may be that there is a problem with the dryer exhaust, you can check what is the system pressure when the dryer is exhausted, if it is normal, then check whether there is a problem with the dryer exhaust port.

4. If the system pressure is very low when the dryer is exhausted, it may be that the pressure regulator of the dryer is damaged, causing the dryer to be exhausted all the time, if it is damaged, it is recommended to replace it again.

The air compressor dryer exhaust is airtight.

1. If the air pressure reaches the maximum, the dryer will be exhausted, which is the reason for the external pressure leakage. 2. After the air pressure is enough, the pressure relief valve on the dryer is opened, the air compressor is basically in a no-load state, and after the car is started, the dryer should be discharged from the bottom once in a while, and there will be water discharged. 3. If the air pressure is lower than the maximum air pressure, it may be that there is a problem with the dryer exhaust, you can check what is the system pressure when the dryer is exhausted, if it is normal, then check whether there is a problem with the dryer exhaust port.

4. If the system pressure is very low when the fruit dryer is exhausted, it may be that the pressure regulating valve of the dryer is damaged, resulting in the dryer being exhausted all the time, if it is damaged, it is recommended to replace it again. Hope it helps.

If my answer is helpful to you, please give a thumbs up (comment in the lower left corner), look forward to your like, your work is very important to me, and your support is also the dynamic and vertical momentum of my progress. Finally, I wish you good health and a good mood!

A: Hello! The air compressor air dryer does not respond when it starts may be due to the following reasons:

1.Circuit Failure: Check the circuit for problems such as power failure, blown fuse, or loose wiring.

2.Switch failure: Check whether the switch is working properly, it may be caused by poor contact or damage.

3.Faulty temperature sensor: If there is a problem with the temperature sensor, the air dryer may automatically shut down.

It is necessary to check whether the temperature sensor is damaged or malfunctioning, and the cracked reed should be replaced in time. 4.Fan failure:

The air dryer needs to circulate air through the fan to work, if the fan fails, it will cause the air dryer to not work properly, you need to check whether the fan is working properly. 5.Heating element failure:

The heating element is an important part of the air dryer, and if the heating element fails, it can cause the entire system to fail. It is necessary to check whether the heating element is damaged or aged and replace it in time. If the problem is not found after the above inspection is missing, it is recommended to contact professional maintenance personnel for maintenance.