Can you repair the handle shaft of the watch if it is broken, and can you repair the broken shaft of

You can repair it, just find someone who specializes in repairing clocks and watches.

It can be repaired, but it needs to be handled by a professional watchmaker. The steps are as follows:1

If the rotating shaft grinder has a relatively light damage, you can first disassemble the watch case, lubricate it with grease, and then put the watch case back; 2.If the rotating shaft is seriously worn, it is necessary to disassemble the watch movement ruler and have the rotating shaft carefully inspected and replaced by the watchmaker; 3.Assemble the replaced rotating shaft back into the movement and lubricate the movement to ensure smooth operation; Lingsui 4

Finally, the lubricated movement is returned to the case and the case is carefully inspected to ensure that the case is in good condition.

Hello, it is a pleasure to serve you and give you the following answer: Yes, the watch hinge is broken and can be repaired. The steps to repair the watch hinge are as follows:

1.First, take the watch apart, remove the hinge, and check for damage. 2.

If the shaft is damaged, you can use pliers to disassemble the shaft and check whether the parts inside the shaft are damaged. 3.If there are damaged parts, they can be replaced with new ones and the hinge can be reattached.

4.Finally, Brother Feng, put the watch back on and check whether the hinge can work properly. Personal Tips:

It takes a certain amount of skill to repair the watch hinge, and if you are not familiar with it, it is recommended to find a professional repairer to help repair it.

When a watch fails, many times the watch handle needs to be removed. Here's how to disassemble the watch: 1. Use a tweezer tool. 2. Use a flat punching tool. 3. Use the instrument to change the cone tool.

1 tweezer tool. You can use the tip of the tweezers to gently press the ends of the pull shaft and gently remove it. Pull the handle outward to the pin position, then gently press the end of the stop shaft with the tip of the tweezers, gradually increasing the pressure, and then pull the handle outward until it is just pulled out.

The force at the end of the pressure and pull block shaft must be appropriate, if the force is too large, the pressure spring will lose its effect, when the handle is reloaded, the pull block can not be stuck in the handle, not only can not realize the interchange of the position of the upper bar and the dial pin, but also the handle will fall out.

2. Plane punching tool. There are two ways to fix the handle and the balance wheel: friction type and riveted type. For friction-fastened shanks, whether they are equipped with wheels or pendulum shafts, the disassembly method is more professional, and the punch used is a V-shaped punch.

If the shaft has been broken and the pendulum shaft needs to be replaced, you can also use a flat punch to remove the handle.

3. Instrument cone change tool. The pull shaft of some watches is threaded with the pull gear, so the pull gear shaft should be rotated 2 or 3 times with the instrument taper, and then the watch handle should be pulled out. If you still can't pull it out, you can rotate it 1 or 2 times again, and pull it while rotating until you can just pull out the handle.

Precautions. When changing the cone with the instrument, pay attention to rotate 2 or 3 times, and then pull out the handle.

Stick it with snot, preferably the thick snot of the yellow one, and stick it firmly.

Summary. 2) The platform of the pull gear shaft (or pull stop screw) supporting the pull gear is uneven, so that the pull gear is cocked, and the groove of the Tissot watch pull gear nail and the shank shaft pull gear nail is too shallow and disengaged.

3) The gap between the pull gear shaft (or pull gear screw) and the main splint hole is too large. When the handle is pulled, the meshing of the watch bracket nail and the shank shaft pull gear nail groove is too shallow and demeshing.

4) The groove wall of the watch stem shaft is damaged. In particular, some back-matched shank shafts are often not quenched and tempered, and the strength and hardness are not enough. When the handle is too tight (the hook is elastic or lacks oil), the pull gear nail breaks the groove wall of the pull stop nail and falls out.

How to repair the watch stem falling off.

Hello This is a very good question, I need a little time to answer, please be patient.

How to repair the stem of the watch:

1) The gap between the shank shaft and the main clamp supporting hole is too large due to wear, which is equivalent to the watch handle shaft sensitive axis moving up, so that the gear nail and the handle shaft gear nail groove mesh is too shallow, and it is easy to pull out the handle. This does not make miscellaneous systems work (e.g. firing, rolling, quick adjustment, calendar, calendar, calendar).

2) The platform of the pull gear shaft (or pull stop screw) supporting the pull gear is uneven, which makes the pull gear warp, and the Tissot watch pull gear nail and the handle shaft pull gear nail groove mesh table is too shallow and demesh. (3) The gap between the gear shaft (or the gear screw) and the world's main splint aperture search and destruction direction is too large. When the handle is pulled, the meshing of the watch bracket nail and the shank shaft pull gear nail groove is too shallow and demeshing.

4) The groove wall of the watch stem shaft is damaged. In particular, some back-matched shank shafts are often not quenched and tempered, and the strength and hardness are not enough. When the handle is too tight (the hook is elastic or lacks oil), the pull gear nail breaks the groove wall of the pull stop nail and falls out.

Summary. Hello, I am helping you to inquire about the relevant case and will reply to you immediately.

Hello, I am helping you to inquire about the relevant case and will reply to you immediately.

Can you describe it in detail?

You'll have to go to a watch shop and fix it with a special tool.

Hello, how to say it. First of all, you can take the after-sales service or professional maintenance of the watch to repair the knob (watch handle) after the watch is broken, and the parts of the watch are connected to the knob by a metal rod, which can be replaced directly after damage, which is not a particularly serious failure.

Hope it helps.

Pure hand lookout.

This watch is good, Montblanc multi-function chronograph watch, but the damage is too bad, you are playing with it, the steel is broken, and the only way to change the dial in this case is to change the dial.

Hello questioner, this can only go to the official after-sales service to replace the new case, there is no other way, adopt it!

What to do if the watch is broken, if the leather is long, you can go to the street to have a special one, do it, if it is short, you want to buy a new one, clothing cloth, common sense of life, watch.

This situation is not easy to handle. If the watch is not expensive, there is no need to repair it, if it is expensive, you need to replace the outer dial, and the estimated maintenance cost and accessories are not cheap.

Go fix it, change the strap!

It is estimated that it will be difficult to repair, so it is recommended to ask at the store.

The old does not go, the new does not come. Or a different bracelet.

This one is broken and can't be fixed! Buy a new one!

Take a look at the watch shop, or go and fix it.

Go to the place where the watch is repaired and ask about it, it should be able to be repaired.

Very good repair! Basically no more than 50 yuan to go to the watch repair shop!

Look at this watch, it's not too expensive, don't spend that energy and time to repair it, it will cost dozens of yuan to repair it simply!

If this watch was given by someone else and you think it is worth remembering, then you can treasure it, maybe it represents some good memories for you!

Sometimes a worthless thing, after a long time, I feel emotional, and I am always reluctant to throw it away, so keep it, find a watch repair master, and ask if I can repair it completely!

This should not be directly broken, but the needle at the head of the watch is lost, and the watch repair shop has it, a trivial matter.

If this shaft is broken, it can't be repaired, so you can only buy a new one!

If the watch strap is broken, you should go to the watch repair shop to repair it or replace it with a new one.

If you buy it, ask the seller, if you go to the store to repair it, you should be guaranteed.

The buckle of the watch is broken, repair the remedy:

1.If it is not serious, take the same needle and thread to repair it, or wrap it with the same leather and sew it again;

2.**It's not expensive, just take it to the repair shop to repair it.

3.If it's still in the expiration date, you can ask the manufacturer to help you get it right.

4.If the quality of the watch is average and does not have much commemorative value, buy another one!

There is no need to repair this, this is very troublesome and expensive, it is recommended not to repair, or to look at other styles.

[Watch maintenance and repair can refer to the service center to go to 702, Xidan Joy City Office Building, Xicheng District, Beijing] to provide Swiss watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

How to replace the buckle: Many watch wearers buy a new buckle after the watch buckle is broken, and want to replace it by themselves, but for those who have no practical experience and do not understand the watch structure, there will be many problems when disassembling and reinstalling the buckle, causing unnecessary trouble. The material of the buckle is also different, if the purchased model is different, the material is not good, the closing strength is poor, easy to deform, etc., it is likely to cause the watch to be lost and dropped; The clasp closure and switch technique used is not good and inconvenient, and it will easily damage the strap.

What to do if the buckle is broken: The watch buckle may be broken and the small tongue falls off, so you don't need to replace the strap, you only need to replace the buckle. Replacing the buckle needs to be carried out by a professional and regular watch repair organization, which can not only ensure the quality of the buckle, but also change to the original model, and there are more kinds of buckles to choose from.

Can't you take care of yourself? Can this also be a bounty issue? Speechless.

Find a professional watch repairer to see if you can fix it.