Questions about P4M800PRO MV1 0A motherboard

1.The capacity of the memory. It's okay to be as small as you want. As long as it is compatible with the motherboard. Generally, DDR2 533 is the smallest at 512MB. It's no smaller.

2 Be sure to have at least DDR2 533 memory sticks. No, it can't be smaller. The frequency of DDR2 533 is the smallest.

It doesn't have to be a 533 either. You can buy DDR2 533 and above frequenciesBecause as long as it is of the same generation.

Memory is backwards compatible. Even if there is no same frequency. , but the memory with the lowest frequency must be installed as required on the motherboard.

It's not good if it's low. Like what. DDR2 800 and DDR2 533 can be used on one board.

It's all the same thing.

3 That motherboard is theoretically supported.

But we have to add it according to the actual situation. The 512MB RAM is now almost generally low. Under that motherboard and that CPU. 1GB of RAM is optimal. More is more. Less is less.

I feel like 1L is messy...

1.Maximum support 4G, 2Not necessarily, DDR2 533 is the smallest second-generation memory...

It's been out of production for a long time now... You can go and buy DDR2 800 or 677... are backwards compatible...

The system automatically recognizes it as 533...

3。The current memory is the price of cabbage,,, but we can't blindly increase the memory... Now the mainstream hardware and software are 32-bit...

So the memory can recognize the large capacity is... Even if you play again, you can't recognize ,,, and more than 3G, many software and games will run incorrectly... So it's good to make it big and make it 3G...

Intel Celeron D P4 PD series Socket 775-pin CPU Via chipset Memory support DDR DDR2 hard RT disk support ATA 100 Qihe 133+2XSATA graphics card supports AGP 8X.

If you want to upgrade the motherboard, I don't know what kind of CPU you are on, if it's P4 or Celeron D, it's not necessary, if it's PD dual-core, you can use the G31 motherboard.

And sorry your motherboard can only support DDR400 or DDR2 533 memory, support Intel Pentium 4 Pentium D-series processors, FSB 1066MHz. It can support DDR 400 or DDR2 533 memory.

Supports Intel Cedar Mill Presler family processors.

Yes, note that it should be double-sided, and single-sided can only use 512m.

Flashing BIOS failed There are three ways to fix it.

1. If the BIOS recognizes the floppy drive, then there is hope You can use the floppy drive to flash back the original BIOS 2. Hot swap Premise: There must also be a board of the same model as yours Use hot swap to restore the BIOS

Three, the last trick is also the safest, use the encoder to flash back the original BIOS, I'm embarrassed, I'm too tired to type, how to get it, check it yourself.

Your COMS (the chip that mounts the BIOS) is corrupted. You take it to the repair shop to replace it with a new chip, and you can re-flash the BIOS and you'll be fine. It is about 30 to 50 yuan, and the charges vary from place to place.

The memory is one-sided. The biggest possibility is that the motherboard doesn't have good memory support. Each physical bank only supports 512M capacity for memory. Single-sided memory generally has only one physical bank, so it can only be recognized 512M.

Solution: The easiest way is to replace single-sided memory with double-sided. If you don't want to change the memory, you can also try to upgrade the BIOS to see, but it may not work, depending on whether the new BIOS support is not supported.

First of all, I don't know if you only installed one memory or installed it at the same time as the previous memory, if it is two memory, and the old one is 512, then it may be that the new one is not plugged in well or other reasons are not identified, if it is only inserted this memory then check the hidden under the c disk directory), see if there is one inside"memmax=512mb"If there is a word, delete it.

How do you tell you about this platform?,There's no need to throw money up.,It's not worth throwing a dollar.,The second-hand graphics card of the agp port has long been garbage.,For the current application,Put it on your board and have no obvious effect.,Your 2nd generation memory module is also automatically downclocked.,If you do an office and play a small game to kill time, the computer can still make do.,If you want to play games, prepare some rice to change the channel.。 It's good to have a host for two thousand dollars.

Since 06, there has been no production of graphics cards with AGP slots.

But there may be an AGP version of GeForce 6600GT in the old parts market, you can ask, it is very cheap, it is estimated that it will not cost 50 yuan.

The power supply problem is simple, in the second-hand market, the 300W rating of the large factory is only 40 yuan.

And sorry your motherboard can only support DDR400 or DDR2 533 memory.

Supports Intel Pentium 4 Pentium D-series processors with 1066MHz FSB. It can support DDR 400 or DDR2 533 memory.

Supports Intel Cedar Mill Presler family processors.

It shouldn't be a problem with the computer, change browsers or see if the network is normal.

Add 1GB of memory, usually do a good job of cleaning junk files and delete unnecessary startup items. You can also take the computer apart and clean up the fan

Upgrade your broadband. up to 8 trillion. Add 1 GB of memory

It's still you.,It should be possible.,Go up and check it out.。 The maximum support can only be up to DDR2 533MHz, you can buy a DDR2 667 for less than 150, and the motherboard will use it as a 533. This motherboard is a transitional product, just in time for the alternation of DDR and DDR2, just like some motherboards now support both DDR2 and DDR3.

Be careful not to plug it in the wrong place.

Yes, but your motherboard is now a low-end motherboard, so I personally recommend Intel5200 or 5300; AMD5000+ is already the limit, choose one of these (if it's high, the motherboard can't move).

Your motherboard is based on the VIA 800 chip on the Intel platform.

Up to support Pentium D805 820