How to repair the toilet flush without water?

This kind of failure shouldn't be a big problem. Start by checking the water pipes for leaks. Check again if the pressure of the water is enough. If it still can't be repaired, you can only replace it with a new one.

Open the water pressure valve to see if it may be stuck, if it still doesn't work, just find a professional maintenance person to repair it.

Hello, in this case, it is best to notify the professional maintenance personnel to repair, this is a minor problem.

It's not hard to change it.

1. Reinstall the pipeline, the impulse of the squatting toilet is small, which may be caused by the abnormal installation of the pipeline, and the pipeline needs to be reinstalled before adjustment; 2. Adjusting the pressure rod of the hydraulic press can increase the amount of water; 3. Adjust the inlet valve, if the water level of the inlet valve is low, the water will become weaker, the inlet valve can be disassembled and reinstalled, and adjusted to the corresponding height.

1. Reinstall the pipeline, the impulse of the squatting toilet is small, which may be caused by the abnormal installation of the pipeline. At this point, the piping needs to be reinstalled before adjustment.

2. Adjusting the pressure rod of the hydraulic press can increase the amount of water; Adjust the inlet valve. If the water level of the inlet valve is low, the water will be weak. The inlet valve can be removed and reinstalled and adjusted to the corresponding height.

3. If the situation does not improve, it is necessary to continue the investigation. First, check if the drain of the tank is blocked by other components or the key lever is too short, resulting in slow and very little drainage.

4. Check whether the sewer pipe is blocked or clogged, whether there is an elbow, etc. Resulting in poor water flow. If so, make appropriate adjustments based on the actual geographical environment.

5. Check whether the switch of the water inlet angle valve is appropriate and whether it can be fully opened. **In public places with a large amount, it is impossible to fill with water within 2 minutes, and the angle valve can be fully opened.

Pay attention to the flushing tank of the squatting toilet, pay attention to the connection between the elbow and the squatting toilet when installing, and the installation position should be appropriate, otherwise it is easy to be blocked, resulting in poor drainage valve.

First check whether the water outlet of the squatting toilet tank is blocked, and then see if the water inlet valve is not fully opened, resulting in only a small part of the water being left. If this is the case, it is only necessary to clean the blocked outlet and open the water valve wide.

If the above reasons are ruled out, you can also check from the following two aspects:

1. The height adjustment of the limit float in the squatting toilet tank is relatively low, resulting in less water stored in the tank each time, and the flushing force is naturally very small.

2. When installing the squatting urinal, the internal rubber sealing sleeve is too tight, so that the water inlet of the urinal is somewhat blocked, resulting in a relatively small water flow into the urinal, and it is more troublesome to deal with this situation, and the squatting urinal needs to be reinstalled.

How to distinguish between high-end and low-end squatting toilets.

1. Generally speaking, the glaze on the surface of the high-end squatting toilet and the embryo body feel relatively delicate to the touch, and there will be no uneven feeling. The glaze of the mid-to-low-end product will be darker, and if placed under the light, you will find pores, and the glaze will be rough to the touch of the embryonic body.

2. The squatting toilet with excellent quality is made of high-temperature ceramics, which is fired at a high temperature of 1200 meters, and there will be a heavy feeling when you touch it by hand. The low-end squatting toilet is made of medium and low temperature ceramics, which cannot meet the requirements of full porcelain.

The toilet can't be flushed, what's going on, hello dear, 1Investigate the cause of the blockage. First of all, we have to check whether the branch bend is blocked due to falling hard objects, and if so, it is best to find a professional to dredge it.

If it's not caused by a hard object falling, then we can try to fix it ourselves. 2.Most households will have toilet suckers, and they can be sold at grocery stores in the market.

When you find that the water can't be flushed after using the toilet, use the toilet to suck the toilet mouth quickly and forcefully squeeze it a few times, continue to flush after squeezing, or continue to use the toilet to suck if you can't flush the branches. It should be noted that the principle of toilet suction is to press down the dirt in the pipe by squeezing the pressure difference in the pipe, so the toilet suction must be perpendicular to the toilet mouth, so that there will be no air leakage when squeezing. Hope it helps.

Solution. The first trick, most of the toilet water flow problem is related to the faucet has a certain interrelationship, the toilet tap water output is less of course, of course, it will cause the water to be slow, there is a filter screen in the toilet water filler position, through long-term application will make the filter screen deposit a lot of dirt, so that the water output will suffer from harm, can be taken out immediately to carry out cleaning. At the junction of the water storage tank, the gate valve is solved to carry out inspection, and the water in the storage tank can be quickly discharged by sprinkling water again.

The second trick, can apply the plastic hose to the bottom of the toilet immediately, can find that the toilet water replenisher is connected with the PVC pipe, the nut is removed with a wrench, the nut of the general toilet is all plastic, it is very easy to disassemble and assemble, and then carry out the dismantling and replacement of the water refiller can also solve the difficulties faster, to understand that the water refiller will endanger the water rate of the toilet at the same time, the water refiller is also very easy to buy in the market, and the process of bone marrow matching is also very simple.

The third trick, cleaning the toilet pipeline can also improve the toilet water rate, the cleaning process can also introduce some detergents with strong decontamination function, so that with the fluidity of the flowing water, the toilet water pipe can be dredged and tidy, no dirt natural water rate will be rapid, and the regular dismantling and replacement of the water pipe can also solve the difficulty, the cost is not high.

The amount of water discharged from the toilet is closely related to the flow rate of the faucet, and if the water from the toilet faucet at home is too small, it will cause slow water supply. Therefore, in the case of slow toilet water, you should first test the filter screen of the water filler to see if there is a lot of dirt deposited on it, if there is a lot of dirt on the filter screen, then you can take it to clean. At the junction of the water storage tank, the gate valve should be checked, and the water in the storage tank can be quickly discharged by sprinkling water again.

After the toilet has been used for a long time, there will be a lot of dirt deposited in the pipeline, and the dirt of the pipeline will accumulate to a certain level, which will also cause the toilet to be slow to drain. Therefore, we can also introduce some detergents with strong decontamination function into the pipeline, so that the flow of flowing water can dredge the toilet water supply pipe neatly, and the natural water supply rate will be rapid without dirt, and the stronger water supply pipe at regular intervals can also solve the difficulties, and the cost is not high.

At this time, it may be because the toilet has been used for a long time, and then it is not easy to use, so it will lead to weak pumping. You can go and replace some of the fixtures inside the toilet.

You can change a toilet, or it may be that the parts in the back are broken, you can buy it accordingly, or you can find a professional repair worker.

Replace the pump. See if the plastic pole in the toilet is adjusted too long, and hold the button to keep the water level low.

At this time, it is time to replace the toilet, which means that the toilet is very old, or the pipe of the toilet is blocked.

There is a problem with the toilet flushing equipment and needs to be repaired, it is recommended to find a professional to repair it.