What to do if the mouse response is delayed Ask for a detailed explanation

1. The fault is caused by the disconnection of the chip connection wire.

The main manifestations are that the cursor is sometimes good or bad or the cursor does not move, and the cursor will shake when you push the connection line by hand.

Solution: First of all, disassemble the mouse, unplug the cable plug from the circuit board, and then mark the correspondence between the pins and the color of the core, cut off a section of the core wire at the position of the broken wire when crimping the wire, and use the hole-shaped pin and crimper to crimp the wire as it is.

2. It may be that the photoelectric mouse is out of order and the positioning is inaccurate.

Photoelectric mice frequently have mouse failure and inaccurate positioning, which is manifested as the mouse often shifts for no reason, and the mouse positioning is inaccurate when used.

Reason analysis: 1) The optical mouse is too good in light transmittance in pursuit of a beautiful and beautiful shell, if the optical path is not well shielded and affected by the external stray light, coupled with strong light interference around, the interference pulse will be generated, resulting in the mouse malfunction.

2) If the temperature is too high, the operating frequency of the crystal oscillator or IC will be unstable and drift.

Solution: Replace it with an integrated circuit or crystal oscillator of the same model and frequency.

Take stock of several common faults of the mouse.

Generally, there are several reasons why the mouse will malfunction, which can be understood.

The mouse is not working, change to a new mouse, and recommend a Rapoo V20 customized version to you.

Wired mouse or wireless mouse.

1. Under the influence of stray light from the outside world, in order to pursue a beautiful and beautiful shell, the light transmittance of the silent mouse is too good, if the optical path is not well shielded, coupled with strong light interference around, it is easy to affect the transmission of the optical signal inside the mouse, and the interference pulse generated will cause the mouse to malfunction.

2. If the temperature is too high, the crystal oscillator or IC operating frequency is unstable and causes drift, at this time, it can only be replaced with an integrated circuit or crystal oscillator of the same model and frequency.

3. The connecting wire chip is disconnected, and the fault is manifested as the cursor does not move or is sometimes good or bad, and the cursor shakes when the wire is pushed by hand.

Solution: Fight God.

1. First of all, disassemble the mouse and unplug the cable plug from the circuit board;

2. Then, mark the correspondence between the color of the core wire and the pin;

3. After the most rock failure, cut off a section of the core base jujube loss line according to the position of the broken line, and use the hole-shaped pin and crimper to press the line as it is.

If this issue is just occurring while playing these two games, it shouldn't be a mouse issue.

The most common is a graphics card driver issue, which can occur when playing games that require the rendering power of the graphics card, which can occur for the following reasons:

1. The graphics card driver is not installed with the most matching program, but is automatically installed by the Windows system, resulting in limited graphics card performance.

2. OpenGL and DirectX rendering are not enabled on the graphics card.

3. If there is a choice of rendering mode in the game, please choose OpenGL or DirectX, the default may be soft acceleration, that is, software rendering, and the game will be stuck when it runs, as if it is in water.

4. Online games may cause image jams due to network blockage, resulting in delays.

Is there a problem playing the game or is there a problem under the whole win? If it's delayed because you're playing the game, do this:

In the screen options in the game's settings, find the option of vsync and turn it off, the English version is called vsync, then off, and then OK, no longer delayed.

You can try adjusting the sensitivity of the mouse.

First of all, I need to see if my mouse itself is not good, you can try to change the mouse, or try to use it on other people's computers to see if it is not normal on your own computer. If it still doesn't work, then it's not a problem with the mouse, if you change the mouse and it's fine, then buy a better gaming mouse.

Computer's settings. Click on the Control Panel. Select the mouse. Pointer options. Check Improve accuracy.

Enter the game, set the screen of the game, and the settings of the mouse, the resolution should not be too high, the picture quality should not be too high, and the CPU should be fully relaxed. Individual games have V-Sync, mouse settings for mouse smoothing.

Hope it helps.

1. First, right-click on the blank space on the desktop and select "Personalization".

2. After personalization appears, click - "Change mouse pointer".

3. You can see the mouse properties in the figure below, and you can change them by clicking the pointer here.

4. You can adjust the speed of the mouse when you click the pointer option, and if you feel that the mouse is slow, you can adjust it to the fast side.

5. The pulley can also be set, but the system can be set by default, which completes the setting of mouse sensitivity.

Mouse latency issues can be resolved with the following settings:

1) Mouse settings solve the problem.

In addition to hardware problems, it is more due to setting problems, the most common situation is that the sensitivity of the mouse is adjusted too high, resulting in the camera not keeping up with the speed of the mouse in the game, resulting in the phenomenon of mouse floating. Find the mouse options in the control panel and switch to the "Pointer Options" tab, where you just need to adjust the sensitivity of the mouse to a moderate position, and most importantly, check off the "Improve pointer accuracy" option.

2) Adjust the hardware acceleration to solve the problem.

Right-click on an empty space on the desktop and select Properties to bring up the Display Settings box, and find the Troubleshoot tab in the Advanced button of Options. Here you can see the adjustment settings of hardware acceleration, under normal circumstances, the default is fully on, and the corresponding hardware acceleration is lowered, basically to 3 or 4 gears.

1. Some old users still retain serial mice due to computer upgrades or merchant reasons. This kind of mouse can be used normally on any type of motherboard with a COM interface, but due to the improvement of the technical content of the graphics card in the new years, especially the graphics card after GeForce2 MX, the graphics card occupies more interrupt resources, and sometimes preempts the COM port interrupt. So when this happens, there will be hardware conflicts, the mouse will not work properly, shaking, scurrying, etc.

If we upgrade the old machine, it is best to use the PS 2 mouse, which will cause the mouse to work abnormally in the future, which will cause trouble for everyone.

2. Interference from external radioactive signals.

Anyone who knows a little bit of hardware knowledge knows that computer hardware enters the work at a certain frequency when working, and the computer at work is most susceptible to the influence of external radioactive signals and causes abnormal work. Sometimes we find that the mouse has frequency jitter, accompanied by frequency wave sound and display jitter, which is mostly due to interference from strong radioactive signals from outside. For example:

High-power electrical appliances and their wiring, mobile phone signals, etc. To solve this kind of problem, we just need to move the computer away from these things, and if space is limited, we can connect a UPS or regulator rectifier in front of the computer wire.

3. Strong light interferes with the normal operation of the photoelectric transmitter and receiver tube inside the mouse.

I don't know if you have noticed that there is a translucent and a black tube on both sides of the transmission wheel when cleaning the mechanical mouse, one is a phototransmitter and the other is a receiver tube. When the mouse is working, it is by relying on the transmission wheel to cut the light regularly and generate electrical signals to make the mouse work. If the quality of the mouse is not too hard or touched or dropped, so that it is not tightly sealed, when there is strong light outside, it will cause photoelectric transmission, and the receiving device will not work normally, at this time, we can use it normally as long as the strong light is covered.

Solution: Wrap the optoelectronic device with black tape.