What should I do if the disk is wrong when the computer starts up, and it can t be started?

It seems that there is a problem with your hard drive, export the useful data to export it, and then use the formatting tool to format the hard drive, and redo the system.

Do you reinstall the system in full format and then reinstall it?

Is it to format all the hard disks and then repartition and reinstall the system?

If that's still a problem.

It must be an error with the hard drive.

You log in with a disc.

Then fix the hard drive.

With DiskGenius

Or. chk

disk command or something.

If it doesn't work, send it for repair.

If you can install the system yourself, install it yourself, if not, go to the place with the computer, (network studio or something) to let them help you reinstall the system up to 15 yuan. It took less than half an hour to get to the stomach.

There are three scenarios for a disk error:

1. False error: It is a false alarm situation of computer system setting error, press F8 to select the safe mode when you turn on the computer, and set it.

2. Soft error: It belongs to the report when the computer is missing system files, and the missing files are copied into it by starting the boot disk.

3. Hard error: It is a physical damage to the computer hard disk and the hard disk needs to be replaced.

Disk partitioning method:

1.Right-click on My Computer and select Manage.

2.On the left side of the pop-up interface, select Storage, Disk Management.

3.On the right, you can see the partition of the computer. Next, move the capacity of one g of drive E to drive F.

4.Right-click on the E-drive and select Compress Volume.

5.In the pop-up interface, enter the amount of compressed space, one g = 1024MB, so enter 1024 here, and click compress after the input is completed.

6.When compression is complete, there will be a free space for a g, inside the black wireframe below.

7.Right-click on the F drive and select Extended Volume.

8.An extended volume wizard will pop up, click Next below.

9.On the left is the space that can be added, and on the right is the space that has already been added. Once you've confirmed the addition, click Next again.

10.When the following page appears, the disk partition merge is complete.

Summary. What should I do if the computer can't turn on and the hard disk is displayed as an error.

Hello dear, <>

In the BIOS settings, set [Antivirus Protection] to enabled;

Restore the BIOS to default, and then plug and unplug the optical drive data cable again, or change the optical drive data cable;

It can be solved by repairing and installing the computer with the system disk or reinstalling the grid.

The solution to the computer disk reading error can not be turned on:

If the disk is read incorrectly, press Ctrl Alt del to restart.

There are many reasons for this problem:

Check whether there is a floppy disk in the floppy drive, then enter the BIOS, adjust the boot sequence to A at the end, and turn off A by the way. Hope my answer is helpful to you, <>

What should I do if the computer can't turn on and the hard disk is displayed as an error.

What should I do if the computer can't turn on and the hard disk error is displayed, hello dear, <>

In the BIOS settings, set [Antivirus Protection] to enabled; Restore the BIOS to default, and then plug and unplug the optical drive data cable again, or change the optical drive data cable; It can be solved by repairing and installing the computer with the system disk or reinstalling the grid. The solution to the computer disk reading error cannot be turned on: the disk is read incorrectly, press Ctrl Alt del to restart.

There are many reasons for this problem: check if there is a floppy disk in the floppy drive, then go into the BIOS, adjust the boot order to A at the end, and turn off A by the way. Hope my answer is helpful to you, <>

How to enter the BIOS settings.

Hello dear, <>

BIOS: Press the "Delete" key when the screen logo appears at boot, use the up and down keys on the keyboard to select the "Advanced BIOS" function, and click "Enter" to enter the BIO....bios：

Press the "Delete" button when the screen logo appears at boot, and the motherboard BIOS setting interface will pop up. BIOS: The way to enter the CMOS on the Phoenix BIOS motherboard is usually to press the "F2" button, and then you can enter the BIOS settings interface.

It is recommended to connect your hard drive to another computer first, and it can be recognized normally, which means that the hard drive itself is fine. Replace a good hard disk data cable, if the boot failure persists, it means that it is not the reason for the data cable. Check the hard disk data cable interface on the motherboard, and find that there is a lot of dust on it, clean the dust on the interface with a soft brush, and blow off the residual dust with a small leather tiger.

The computer shows that the hard disk cannot be found solution:

1. After entering the BIOS first, select the "IDE HDD Auto Detection" item to see if the existence of the hard disk can be detected, and check whether the model is consistent, if the hardware problem is ruled out normally, if the hard disk cannot be found, then your hard disk is damaged or connected incorrectly.

2. If the hard disk can be viewed in the BIOS, generally the main boot sector of the hard disk is damaged, you can use the PE system with DOS toolbox to run the DOS command "fdisk mbr" to try to repair the main boot sector of the hard disk.

3. If the method in step 2 does not work, you can try to restore the BIOS to the default settings.

4. Sometimes there is some kind of error in the system, which may cause the system to fail to recognize the hard disk, use the system installation disk to repair the system or reinstall the new system.

5. If it is a hardware failure, it is recommended that the customer fork the computer case and fork the relevant wiring of the hard disk, if the problem cannot be solved, it is recommended to send it to the local service station for maintenance.

Dear, the result you get here: The computer can't turn on and the hard disk error is usually displayed in the following situations and solutions:1

Physical damage to the hard drive: If the hard drive is physically damaged, the computer will make a different noise when it is turned on, or an error message such as "hard drive not found" will appear. At this point, the hard drive needs to be replaced or sent in for repair.

2.Hard disk file system corruption: Hard disk file system corruption may be caused by computer power failure, improper operation, etc., in this case, you can try to use the chkdsk tool that comes with the Windows system to repair.

To do this, press F8 to enter safe mode when booting up, select "Command Prompt", enter the chkdsk fr command, wait for the inspection and repair to be completed, and then restart the computer. 3.

Hard disk connection problem: Poor hard disk connection or damaged power cord will also cause the hard disk error when the computer is turned on, so you need to check whether the hard disk and power cable are connected securely. You can try replugging the drive and power cord, or replacing the power cord.

4.Virus Infection: Virus infection can also lead to hard drive errors.

In this case, you can try to use antivirus software to scan and remove the virus. If the computer does not turn on, it can be operated in a safe mode of ignition. In short, the computer can't turn on the hard disk error may be caused by a variety of reasons, which need to be judged and dealt with according to the specific situation.

If none of the above methods can solve the problem, it is recommended to contact a professional computer repairer for repair.