How to drive a car to apply for fuel efficiency, how to drive a car to save fuel?

Good fuel saving results are not only determined by the technical condition of the vehicle, but more importantly by how it is driven. Scientific, skillful, and proficient driving skills can reduce fuel consumption. 1. Don't blast the oil before starting or turning off the fire.

Some drivers are accustomed to blowing up the fuel before starting, in fact, this has all kinds of harm but no benefit, it not only aggravates engine wear, causes environmental pollution, and consumes liters of fuel every time you hit the throttle. 2. Do not heat up and idle for a long time. The average car idling consumes more fuel per hour than one minute, which is more than the amount of fuel used to restart the engine once.

3. Don't stop suddenly and accelerate suddenly. Before stopping, you should plan in advance, do not brake with one foot if you want to stop, and try to use the inertia of the car to coast and stop the park. Sudden acceleration consumes more fuel than even acceleration.

Fourth, do not stop and go and abuse the brakes. Try to avoid traffic jams on the way before driving, because stop-and-go consumes more fuel than normal driving Brakes should be minimized during driving, and the engine and low gear should be fully utilized. Fifth, the driving speed is moderate, not too fast or too slow.

In order to prevent red lights at every intersection, try to synchronize the speed with the rhythm of the signal light change to avoid stopping at a red light. 6. When driving, you should choose the road surface correctly and do not rush and collide. According to the test, it has been shown that

Driving on uneven roads consumes more fuel than driving on good roads Do not drag uphill, do not accelerate sharply, and downhill under the condition of ensuring safety, try to use the slide, but do not turn off. 7. Less short-distance travel. Short-distance cars do not make the most of the engine's optimal efficiency.

If you can merge multiple times into one, you can not only give full play to its work efficiency, but also reduce the wear and tear of the vehicle and effectively save fuel. 8. Plan to drive a long-distance bus and don't travel blindly. First of all, we must be familiar with the route to prevent the east and west from looking for unjust oil; secondly, go to bed early and get up early, and avoid the peak period when there are many people on the road; Again, try to use air conditioning sparingly.

If possible, avoid bad weather such as rain, fog, and snow. Driving against the wind consumes the same amount of fuel 9. Choose an economical speed, don't blindly pursue fast. Take Santana as an example, driving at km/h on a straight road is the most fuel-efficient, and if you drive at km/h, it will consume more fuel If you drive at km/h, it will consume more fuel 10. Don't carry unnecessary items.

Weight is the biggest enemy of oil consumption. For every kilogram of items, the vehicle increases fuel consumption by about .

1. Soft start Start in low gear, slowly press the accelerator pedal, and accelerate slowly. When the car reaches a certain gear speed, gradually change the gear from low to high. This can reduce the heating time of the engine, and the big reed can increase the fuel utilization.

If you hit the throttle to speed up when starting, it will not only hurt the car but also greatly increase fuel consumption.

2. Gently lift the throttle Lifting the throttle sharply will make the engine speed suddenly decrease and play a role in hindering, offset part of the driving inertia, and make the car "flutter", so that the fuel consumption increases.

3. High-gear driving.

Avoid low-gear high-speed driving, use high-speed gear as much as possible when driving, and use less intermediate gear. But don't drag in high gear.

4. Shift gears in time.

The quicker the shift time, the better the car's dynamics and the more fuel can be saved.

5. Use economic speed.

The economic speed of a general car is between 60kmh and 80km/h. It is most fuel-efficient when the car is running at an economical speed. Whether the speed is too high or too low, it is not good for fuel saving.

When the speed of the vehicle is low, the movement speed of the piston is low, and the combustion is incomplete. At high speeds, the increase in the speed of the intake leads to an increase in the intake resistance of the Yuzheng, which increases fuel consumption.

6. Reduce the use of braking.

Braking is essentially a process of energy conversion, and braking means the consumption of energy. Therefore, when passing through intersections and downhill slopes, you should lift the accelerator in advance, and keep enough following distance between the driving and the car in front, so that you can not only slow down calmly, but also reduce the number of braking. In order to achieve the purpose of fuel saving, it is necessary to avoid frequent rapid acceleration and sudden braking, and maintain a constant speed.

7. Avoid idling for a long time.

Many riders have the habit of getting up early to warm up the car to protect the engine, reminding friends who have this habit that "the warm-up time should not exceed 3 minutes as the best, and it is useless and fuel-efficient to warm up the car for a long time." The EFI car does not need to warm up the car, and it can be operated in the morning. Carburetor car, etc., when the water temperature gauge pointer crosses the lowest line, you can walk the car.

In addition, the engine should be turned off when there is a traffic jam or a long waiting time, and the fuel consumption of the engine idle for more than one minute is more than that of restarting.

8. Use the air conditioning and refrigeration system correctly.

Air conditioning consumes a certain amount of fuel, and some car owners will turn off the air conditioner and open the windows for ventilation. In fact, when the speed is higher than 80km, the air resistance of the rolling belt after opening the window consumes more fuel than air conditioning and refrigeration.

Don't accelerate sharply, don't step on the brakes frequently, maintain on time often, don't often stop in one place for a month or a few months, good luck.

Tip 1: Good driving habits.

When driving in urban areas, using the default mode or SPORT mode, the fuel consumption will be 3%-5% higher than that of the ECO mode. If you often drive in urban areas, you can use ECO mode, and avoid rapid acceleration and slow acceleration when driving in urban areas, which is both safe and fuel-efficient.

Cheats 2: Wait for the traffic light to hang the n gear.

Borui car owners can wait for the traffic light, hang D gear to step on the brake or turn on the Auto Hold function, the engine needs to overcome its own resistance, but also need to overcome the resistance of the automatic transmission torque converter (only for without a start-stop system), additional fuel consumption at idle, it is recommended to hang N gear when waiting for the traffic light. Borui GE (MHEV) owners keep the start-stop system always open, do not manually turn off the start-stop system, try to avoid rapid deceleration, fuel consumption is ideal; PHEV owners often charge their batteries.

Tip 3: Turn on the auto mode of the air conditioner in summer.

If it is set at max, the air conditioning compressor will run non-stop, the blower will also be at the highest air volume, the temperature difference between the inside and outside of the car is too large, and people are also prone to colds.

Tip 4: Protect your tires.

Maintaining a standard tire pressure, too low or too high tire pressure will cause varying degrees of wear and tear on the tires, and will also affect the fuel economy of the vehicle.

Tip 5: The car should be maintained on time and the "three filters" should be replaced regularly

Oil filter, fuel filter, air filter.

Tip 6: Avoid opening windows when driving at high speeds.

Tip 7: Reduce the use of electrical appliances.

The use of electrical appliances in the car will consume a lot of electrical energy, such as multi-** display screens, etc., and try to turn them off when not in use.

Tip 8: Travel light.

Don't load unnecessary items when driving, lighter cars can also save fuel, and fuel consumption increases by 2% for every 100kg increase in weight.

Tip 9: Don't modify blindly.

Do not change the size of the tyre, the wider the tire, the louder the noise it will produce, and the greater the resistance, resulting in higher fuel consumption.

Tip 10: Maintain your vehicle on time.

Do maintenance according to the specified time to keep the vehicle in good condition. Good engine running condition not only contributes to improved driving safety, but also helps to reduce fuel consumption.

Regular maintenance, use suitable oil, obey traffic rules, reduce accident rate, regularly clean the fuel tank, check the gas and oil circuits.

After parking, turn off the engine and do not idle, tighten the hand brake, remove the key, roll up the window, and leave after seeing safety. The following is how to drive a car for you to save fuel, I hope it will be helpful to you Chakai.

Ways to save fuel in your car.

1. Slow acceleration from low gear start:

The car starts in low gear and accelerates slowly. Avoid throttle and hard acceleration.

Second, step on the accelerator gently and slowly, and quickly seize the opportunity to shift gears

Slamming the accelerator pedal will result in an "extra" fuel supply and increased fuel consumption. Sudden lifting of the throttle will offset part of the driving inertia due to the sudden decrease in engine speed, resulting in an increase in fuel consumption.

3. Fuel consumption reduction at economic speed

Economical speeds are often not reached in cities, and when the road conditions are good, the speeds are much higher than the economic speeds, which are all fuel-guzzling factors. The economic speed of the car is usually designed in the range of 70-90 kilometers per hour, and the car is most fuel-efficient at this speed when driving in high-speed gear.

Fourth, straight driving is more fuel-efficient

The car is more fuel-intensive when turning than going straight. Because the resistance increases when turning, more energy will be consumed; Passing through corners requires upshifting and downshifting, and each gear change consumes more fuel. Therefore, if you will reach your destination in a straight line or a turn, you should try to go straight as much as possible.

If you have to turn, you should relax the throttle before turning, gradually reduce the speed to the right speed, and maintain stability. Try to avoid applying the brakes in corners, and if you slow down, it's best to use the engine brakes.

If you want to save fuel, you still have to rely on the accumulation of ordinary driving, and if you drive with good habits, you will save fuel. Introduce a simple and easy method: 1. Maintain the normal value of tire pressure and check the air pressure regularly.

2. Think about the journey before going on the road, and don't take the wrong road. 3. Try to use engine oil with low viscosity, and save fuel when the engine saves effort. 4. Maintain the engine regularly and replace the three compartments (three filter elements) regularly.

5. Don't start the engine first when the car is not gone, stop and wait until someone turns off the engine. 6. Don't slam on the accelerator to accelerate, it will save fuel if you follow the point. 7. Steady driving speed, but rapid acceleration but not rapid reduction.

8. Reduce the weight of the vehicle itself and do not place excess objects. 9. When encountering a red light, throw away the accelerator in advance to reduce the speed, and try to avoid sudden braking. 10. Maintaining good driving habits is the best fuel-saving foundation.

11. The current automobile engine is controlled by electronic sensors and electronic controllers for fuel injection ignition, and at a certain operating speed, the throttle is relaxed without neutral gear or clutch, which is driven by inertia, and the engine will stop fuel injection and ignition, which has the effect of fuel saving. This is a good driving foundation, every time you encounter a red light or a downhill section during driving, you can lose the accelerator and not hit neutral, so that the inertia pushes to run this is fuel-efficient.

Driving at a constant speed of 50-75% of the throttle (throttle) opening is the economic speed, which varies from car to car. After the engine starts, the water temperature gauge pointer can be started, after starting to rise to the highest gear in a short time, do not slam the accelerator pedal, the engine speed is best not to exceed 2000, less brakes, do not coast in neutral gear. Do not idle for long periods of time.

After driving for a long time, the car should be cleaned with EFI and air intake, and the idle motor, which should have a thick layer of sludge in it for a long time. The engine oil can not be added too much, the car will be stuffy and wasted fuel, do not slam the accelerator and brake sharply during driving, the trunk can not put too much to increase the weight of the car will also consume fuel, useless things try not to put in the car, and there is always check the air pressure of the tires.

Foot light, don't rush to refuel, shift can be early, you can change at 2000 rpm, don't wait until 2500 rpm, high-end and low-speed can save a little, but the gearbox wear is relatively large. The economic speed of the average car is about 60 kilometers per hour, and at this speed, don't be too fast, don't be too slow.

Accelerate slowly, brake less. Novices don't worry about fuel consumption, a few more money, safety first.

Everybody's written is very comprehensive, good, and can be adopted.

Everyone wrote very comprehensively!!It's all good, and it's all adoptable.

Keep the car's engine speed at around 2500 and be stable.

In order to save fuel for car owners, we provide nine ways to save fuel before maintenance and on the road for car owners' reference.

1 Take care to clean or replace the air filter with a new one.

2. Regularly maintain the combustion system (carburetor or fuel injector), and the spark plug should be cleaned and replaced regularly.

3 Change the engine oil and oil filter on time to reduce internal friction in the engine.

4. Choose appropriate oil, otherwise it is easy to cause engine damage and increase fuel consumption.

5 The fuel tank cap should be locked tightly, and the oil should not be overfilled to avoid oil overflow.

6. Tires should be kept at proper pressure, as insufficient tire pressure will consume more fuel; High tire pressure will reduce tire grip and cause punctures.

7 Do not pile up non-essential items in the car, and reduce the interior decoration of the car to avoid increasing the load on the vehicle.

8 Keep the time between engine start and start as short as possible, preferably no more than three minutes.

9. Always pay attention to the engine cooling system to keep the engine at a normal temperature to avoid cylinder wear.

10.Minimize the time the air conditioner is on and reduce fuel consumption.

1. Follow the methods recommended in the car maintenance and repair manual——— a well-maintained car is more fuel-efficient to drive, dirty spark plugs, dirty air filters or clogged filters will reduce fuel economy.

2. Keep the tire pressure at an appropriate level——— if the tire pressure is too low, it will cost more fuel, so you need to check the tire pressure frequently.

Tyre pressures that meet the required requirements can reduce fuel consumption by one percent.

3. Reduce the burden on your vehicle——— overweight vehicles will consume more fuel when driving. Therefore, try to empty the suitcase, do not use the trunk as a storage room, and do not pile up non-essential items in the car. If you don't use your luggage or ski rack, remove it.

4. Don't drive too hard——— step on the accelerator after parking, and press the brakes hard and accelerate sharply, these behaviors will increase fuel consumption.

5. Try to hang high gear——— low gear will consume more energy, so when driving a car with a manual transmission, you should change to a high gear in time after the speed stabilizes, and try to avoid using the "sport" mode when driving a car with an automatic transmission.

6. The use of cruise control ——— on flat roads can be used to save fuel, but this method is not the most economical on steep terrain.

7. Keep your vehicle clean——— frequent car washing and waxing can reduce air resistance, which can improve fuel economy.

8. Avoid letting the car idle for a long time——— the vehicle will also consume fuel when the engine is idling. If possible, try to turn off the engine while you stop and wait, and don't let it spin all the time.

9. Try to use air conditioners as little as possible——— air conditioners can consume a lot of fuel. Opening the windows on both sides can reduce air resistance, so you should open the windows when you are driving slowly in traffic jams, and turn on the air conditioning when driving at high speeds. (Opening windows at high speeds can increase drag).

10. Accelerate after warming——— it is more fuel-intensive for the engine to run at low temperature than after the temperature rises, so don't accelerate immediately when you start it, but slow down for a few minutes to let the engine heat up and then accelerate.