The TL WR703N wireless connection will not use 20

This kind of thing is set up in a fool's way.,As long as you plug in the network cable.,Configure the password.,Other people's devices can be connected.。

However, if you plug in the cable directly from the cat, you need to enter the router to configure the Internet account and password, and then set the wireless password. If it is a cable pulled from a router or community broadband, you can use it without configuring an Internet account, and you can use it directly by setting up wireless.

It should be noted that all computers that want to use this router should be set to automatically obtain the IP, because the gateway of this router is set when the IP is manually set on some computers. Change it to get it automatically.

If you can't solve it, you can ask again.

The route has a static IP and a cloned network card MAC, you clone the MAC and Ruijie authenticated IP (to clone your local connection to the MAC, change your authenticated IP and then proceed to the next step).

First of all, you have to use the network port slot in the dormitory to connect the network cable to the computer, so that the computer can be authenticated to confirm that it can access the Internet;

Secondly, so that the computer can surf the Internet without Ruijie authentication, first disable the local connection, and then switch out of the task manager to end Ruijie (there seems to be an 801? I forgot the name.,Just end it),Then enable the local connection,See if you can access the Internet,If not,Then re-authenticate Ruijie,Then disable the local connection again,Then end the Ruijie task,Then enable the local connection。 Until you can use the Internet without Ruijie.

Finally, directly unplug the network cable head connected to your computer's network port, plug it into the WAN port of the wireless router connected to the power supply, and see that the computer is connected with a wireless network card and the IP is set to automatically obtain (the mobile phone can also be connected to wifi, but if the data has not been transmitted for a long time, it will be broken, and then use the computer to open the page wirelessly, and the Tianyi certification page will pop up to authenticate on the line). Remember if the power is off,You have to clone the MAC and IP of the wireless router again,Just follow the above steps again,My dormitory is the wireless router I set,But it's just to let the mobile phone wifi Internet access,And your own computer use。

Remember to set a wireless password, otherwise you will be connected to other dormitories to trawl speed.

Is it a problem with the setting poke a small hole.

Reset it and try again.

Are you using AP mode? Change to wireless routing mode and try it:

1: Mode selection.

The TL-WR720N hardware switch is toggled to "Wireless Routing Mode".

2: The connection of the router.

The network cable of the mobile broadband is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

3: Log in to the router.

Open your computer browser, enter the routing IP in the address bar, and enter the login dialog box! Enter the username and password admin, and the password is admin.

4: Set up your router.

Open the management page of the TL-WR720N and enter the Setup Wizard. Select PPPOE to access the Internet, and enter the broadband "Internet access" and "Internet password".

5: Set the name of the wireless network.

Set the SSID (that is, the wireless network name) of the TL-WR720N. We recommend that you set wireless security, select "WPA-PSK WPA2-PSK" and set a PSK password.

6: Restart your router.

Click "Restart", the router will automatically reboot and the setup is complete.

7: Reconnect the router.

After the reboot is complete, you need to reconnect to the wireless network of the TL-WR720N, and enter the wireless PSK password of the TL-WR720N during the connection. The computer host can be directly connected to the Internet.

Since the other network cables are normal, it is not a problem with the router. It's a problem with the network cable, if it's a dial-up ** line, there is a cat in front of the router, use the cat to dial up, and then connect the router to the line that comes out of the cat.

Are you using a cat? You can see if you set up a static or dynamic connection, if there is a cat, it should be static, and then see if your password is not mistyped

One is connected to the computer, the other is connected to the router, and it is actually very simple to enter the router settings center to set it up.

The TL-WR703 is a pocket-sized mini wireless router with only one WAN wired multiplexing interface, so your original R402 can't be eliminated yet. You should buy a commonly used one with 4 LAN ports, in which case only one router is enough.

If you have too many things, you will be prone to problems. One of the reasons why you can't connect normally is that the default management IP of the two routers is conflicting with each other; Another TL-WR703N has a lot of differences from other wireless routes, you have to modify its routing settings according to your broadband situation.

The first step is to modify the route settings of the TL-WR703N. Because the router does not have DHCP enabled by default, you must manually set the IP address to the computer to connect to the router. The router is plugged in but not plugged in with a network cable, and the laptop wireless connection is set to any value in between), subnet mask, default gateway.

After the wireless network card is connected normally, enter the router management interface in the notebook browser, and change the default 3G routing mode to wireless routing mode in the working mode; Select the dynamic IP, turn on DHCP, modify the management IP to, and other settings of the wireless password or something, save and restart the router.

The second step is to change the wireless connection IP of the laptop back to automatic acquisition, and plug the TL-WR703N into the network cable, and it can be used normally.

That's because you have two routers, and the addresses that come out are all segmental, and there is a conflict.

You first change the local address of your wireless router. Don't use the WAN port that can be replaced with or something else, the wireless port setting should be dynamic IP and then restart.

The wiring should come out of the wired router and lead to the blue port of the wireless router, which generally says WAN port.

This wireless router does not have DHCP turned on by default, the wired port under the AP is LAN, then the wired is manageable, and the wired port under the setting of routing or virtual dialing is WLAN, at this time, the wired can only be managed wirelessly without being set to remote management.

After the factory reset is done, set the local wired NIC of the computer to automatically obtain the IP address, and then use the network cable to connect the LAN port of the router to see if the computer can get the IP address. If you can't get it, it's estimated that you can.

First of all, can your desktop computer be connected to the Internet through a wireless router (if so, can you plug in the cable directly, or do you have to dial in the computer after plugging in the wire?) ）

Second, refer to the settings in this diagram.

Third, if it still can't be solved, it is recommended that you reply to my first question first, and then intercept the map of the router's running status (especially the part of the WAN port) to ask, and I will look at the data.

A wireless router must be the primary route or a route setting that relays other wireless signals in order to be a route transmitter for wireless signals. You have a wireless signal before, you want to use your router to collect the wireless signal as a wired signal for your desktop, your router has a bridging function, you try, if it doesn't work, then you use your router as the main route to transmit signals, you can use it as wired, and wireless together.

Does your wireless router turn off DHCP?

The TL-WR703N cannot access the Internet using a network cable connection, and the fault may be at the operator's network or the router, and it must be tested to determine the specific fault point:

1. Set up the dial-up connection according to the requirements of the operator, connect the stand-alone device to the operator's optical modem, and ping the operator's gateway or DNS server address after dial-up the Internet;

2. If the ping is not working, it means that the operator's external network network is not connected, just call ** to find the operator to report for repair;

3. If the ping means that the external network network is normal, it has nothing to do with the operator's network, and the fault is on the router, restore the router to factory settings, and then reset it to eliminate the fault.

4. If the router still fails after step 3 above, you can judge that the router hardware is faulty and you can only replace the router.

You should use wireless AP mode.

TL-WR703N Setup Guide (3) - Wireless AP Mode TP-Link Technical Service.

Note that the IP address of the WR703N should not be in the same segment as the unit router.

How to set up a wireless router.

Home Network Environment Cabling:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer into the router:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set up router dialing:

1. In the [Setup Wizard], select [PPPoe Dialing] (some are ADSL Dialing), enter the Internet user name and password according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function:

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set a wifi password.

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

The problem must be with the route, reset or restore the route. Log in again.