What are the advantages of the instrument of the image measuring instrument and what are the measure

You mean the video steel ruler tape measure probe, right? This SJ2460 image-type steel tape measure tester is a fully automatic verification of steel tape measure, I will briefly tell you about its 5 points:

1. Automatic retraction and placement of ruler belts and positioning lines.

Before measuring the steel tape measure, you only need to set the relevant calibration parameters of the steel tape measure on the verification software, and then click "Start".

The instrument will automatically position the 0 scale line, and then start to put the long tape for verification;

2. Automatically complete the line measurement.

The system automatically completes the line pattern measurement, which reduces the labor intensity of the operator and avoids the error introduced by manual operation. The instrument supports autofocus operation to minimize the degree of manual intervention.

3. Automatic calculation, automatic processing of data, and automatic generation of reports.

The measurement software can automatically save the data, automatically calculate the verification results and determine the verification conclusion according to the regulations, and can automatically generate reports for the

Customers preview and print, and include verification records and verification certificates.

4. Higher precision.

The instrument adopts a standard glass line ruler to calibrate the distance between the cameras at fixed points as the standard length. At the same time, the measurement does not rely on manual work, and can achieve higher measurement accuracy.

5. Faster verification speed.

It only takes a few seconds for a fixed checkpoint camera to complete the camera capture and line value processing of the verification point.

This is the product of modern science and technology, are the crystallization of artificial intelligence, so compared with the old steel tape measure verification method, this instrument greatly improves the work efficiency, but also makes the work of the inspectors easier. Hope it helps!

1. Equipped with 2 adjustable light source systems, not only the contour of the workpiece can be observed, but also the surface shape of the opaque workpiece can also be measured.

2. The use of cold light source system can avoid the error caused by the deformation of the workpiece that is easy to deform due to heat.

3. The workpiece can be placed at will.

4. The operation of the instrument is easy to master.

5. It is convenient to measure, and only needs to be operated with a mouse.

6. The measurement that can be done after adding the probe sensor in the Z-axis direction.

The image measuring instrument can automatically capture data points, measure geometric features such as points, lines, circles, arcs, ellipses, rectangles, etc., and automatically analyze various parameters of measurement features, such as width, diameter, position, straightness, cone, cylindricity and other geometric dimensions. The instrument is characterized by the ability to automatically grasp the boundaries and surfaces of the product, especially when measuring some weak edge features (such as transition curves, fillet machining, etc.). Combined with the survey software, the surveying and mapping element data is processed, evaluated and output.

On the premise of ensuring accuracy, the measurement efficiency is higher.

Measurement function. 1.Measurement tools: scan to extract edge points, multi-segment edge points, circle edge points, ellipse extraction, box selection to extract contour lines, focus points, closest points, etc.

2.Measurable geometric quantities: point, line, circle (center coordinates, radius, diameter), arc, center, angle, distance, line width, hole position, hole diameter, number of holes, distance from hole to hole, distance from hole to edge, distance from center of arc to hole, distance from center of arc to edge, distance from high point of arc to high point of arc, distance from intersection point to intersection point, etc.

3.Construction features: infiltration intersection, center point, extreme point, endpoint, two-point connection, parallel line, perpendicular line, tangent line, bisector line, center line, line segment fusion, radius circle, three-line inscribed circle, two-line radius inscribed circle, etc.

4.Geometric tolerance: straightness, roundness, contour, position, parallelism, symmetry, perpendicularity, concentricity, parallelism and other geometric tolerances.

5.Coordinate system: instrument coordinate system, point line, two point x, two lines and other workpiece coordinate systems; image registration coordinate system; The coordinate system can be translated, rotated, and manually adjusted.

6.Quick tools: R angle, horizontal pitch, circumferential pitch, screen, slot, contour comparison, springs, O-rings and other special tools for quick measurement.

7.Support tolerance batch setting, proportional grade division, and custom management.

Now we are using a new type of image measuring instrument - flash meter, its function is much higher than the traditional imager, now I will give you a detailed introduction to this instrument.

VX3000 flash meter.

The flash tester can measure all kinds of two-dimensional dimensions, such as length, width, diameter, radius, angle, center distance, gear parameters, thread parameters, spring parameters, O-ring parameters, etc.

High <> efficiency. When the flash measurement bureau line Zheng Yi in the measurement, only one key, a few seconds can complete the measurement, each time can measure up to 512 positions, CNC mode can be used for batch measurement, at the same time, the automatic identification function of the flash tester, the product can be completed without alignment, so the measurement efficiency is extremely high.

2.Good accuracy.

The flash tester autofocuses and automatically identifies the measurement part, which reduces the influence of the operator on the measurement results, and the repeated measurement accuracy of the same product with beam can maintain a high degree of consistency, and the same measurement results can be obtained by different personnel operations.

3.It's easy to use.

Simple operation is also one of the main features of the flash meter, which can be completed with a mouse, even if it is a novice, it only needs simple training, and the operator is relatively not too high to ask for it.

4.Convenient data processing.

The flash tester automatically generates the test report with one click, and automatically outputs the SPC analysis report, which is convenient and fast.

In fact, you can ask the staff of Mingwei directly, Mingwei's image measuring instrument is a relatively high-end equipment in the domestic image measuring instrument, we also use Mingwei's two-dimensional image measuring instrument, the configuration is relatively high, the quality is very good, we have been using it for several years, and the equipment has not had any problems! The image measuring instrument generally has the following major functions: 1. Multi-point measurement points, lines, circles, solitary circles, ellipses, and rectangles to improve measurement accuracy;

2. Combined measurement, center point structure, intersection point structure, line structure, circle structure, angle structure;

3. Coordinate translation and coordinate alignment to improve measurement efficiency;

4. Aggregation instruction, batch measurement of the same workpiece is more convenient and fast, and the measurement efficiency is improved;

5. The data of measurement Weilu macro is directly input into AutoCAD to become a complete engineering drawing;

6. The measurement data can be input into Excel or Word for statistical analysis, and a simple XBAR-S control chart can be cut, and various parameters such as CA can be obtained;

7. Multi-language interface switching;

8. Record the execution of user programs, instructions and teachings;

9. Large map navigation function, special three-dimensional rotating light for knife mold, 3D scanning system, fast autofocus, automatic zoom lens;

10. Contact probe measurement can be purchased, and the software can freely realize the conversion of probe image photo albums, which is used for contact measurement of irregular products, such as ellipse, radian, flatness and other dimensions; You can also directly use the probe to dot and then import it into the reverse engineering software for further processing!

11. The image measuring instrument can also detect the roundness, straightness, and radian of round objects;

12. Flatness detection: the flatness of the workpiece is detected by the laser probe;

13. Professional measurement function for gears.

14. Special measurement function for test screens used in major metrology institutes across the country.

15. Comparison function between drawings and measured data"

The advantages of the image measuring instrument are: 1. It can detect the size of blind holes, grooves and other dimensions on the upper surface of the object to be measured. The image and color on the surface of the workpiece can be clearly seen.

2. The image can be output to the computer and used software to map and save the disk. You can take photos, print, and save them.

3. The computer software surveying and mapping function is more powerful than the traditional projector, which can output the graphics to AutoCAD, and the engineering drawings of AutoCAD can be input into the software, and the customer coordinates can be set at any time, and there are many methods to measure the size. The measured graphics can be output to Word, Excel for measurement reports, etc., and can also be used for SPC statistical analysis reports.

4. The magnification of the lens of the image measuring instrument can be adjusted from 20 times to 120 times, etc., if the projector wants to change the magnification, it is necessary to change the lens one by one and buy a lot of lenses.

5. The image measuring instrument is based on the projector to cultivate a lot of research and development and testing, and the whole market has long been mature, accounting for 90% of the market power compared with the projector.

6. All the workpiece imagers that can be measured by the projector can be measured, but most of the workpiece projectors that can be measured by the imager cannot be measured.

"In fact, you can ask the staff of Mingwei directly, Mingwei's image measuring instrument is a relatively high-end equipment in the domestic image measuring instrument, we also use Mingwei's two-dimensional image measuring instrument, the configuration is relatively high, the quality is very good, we have been using it for several years, and the equipment has not had any problems! The image measuring instrument generally has the following major functions: 1. Multi-point measurement points, lines, circles, solitary circles, ellipses, and rectangles to improve measurement accuracy;

2. Combined measurement, center point structure, intersection point structure, line structure, circle structure, angle structure;

3. Coordinate translation and coordinate alignment to improve measurement efficiency;

4. Aggregation instruction, batch measurement of the same workpiece is more convenient and fast, and the measurement efficiency is improved;

5. The measurement data is directly input into AutoCAD to become a complete engineering drawing;

6. The measurement data can be input into Excel or Word for statistical analysis, and a simple XBAR-S control chart can be cut, and various parameters such as CA can be obtained;

7. Multi-language interface switching;

8. Record the execution of user programs, instructions and teachings;

9. Large map navigation function, special three-dimensional rotating light for knife mold, 3D scanning system, fast autofocus, automatic zoom lens;

10. Contact probe measurement can be selected, and the software can freely realize the conversion of probe images to each other, which is used for contact measurement of irregular products, such as ellipse, radian, flatness and other sizes; You can also directly use the probe to dot and then import it into the reverse engineering software for further processing!

11. The image measuring instrument can also detect the roundness, straightness, and radian of round objects;

12. Flatness detection: the flatness of the workpiece is detected by the laser probe;

13. Professional measurement function for gears.

14. Special measurement function for test screens used in major metrology institutes across the country.

15. Comparison function between drawings and measured data"

Automatic optical image measuring instrument. It solves the problem of dimensional measurement of printed circuit boards (PCBs) with 2D precision measurement. It also has the characteristics of high speed and precision, and can perform multiple functions on a single machine, greatly reducing the waste of repeated phone bills and empty space.

The SOV series is a general-purpose 3D precision measurement and programming system. The measurement object can be a PCB, a negative, or other object with 2D characteristics. He can measure the center of the circle (arc), radius, line width, angle, distance, and intersection point on the object; It also has the function of automatic batch measurement and programming; The system includes basic image processing functions, such as deburring, centerline, etc.; In addition to that, it has features like statistical analysis, autofocus, auto-detection, and more.

SOV series products its detection software is developed in the Windows environment, with pervasive, drawing, image display and other functions, the system operation is simple and flexible.

1. Multi-point measurement of points, lines, circles, solitary circles, ellipses, and rectangles to improve measurement accuracy;

2. Combined measurement, center point structure, intersection point structure, line structure, circle structure, angle structure;

3. Coordinate translation and coordinate alignment to improve measurement efficiency;

4. Aggregation instruction, batch measurement of the same workpiece is more convenient and fast, and the measurement efficiency is improved;

5. The measurement data is directly input into AutoCAD to become a complete engineering drawing;

6. The measurement data can be input into Excel or Word for statistical analysis, and a simple XBAR-S control chart can be cut, and various parameters such as CA can be obtained;

7. Multi-language interface switching;

8. Record the execution of user programs, instructions and teachings;

9. Large map navigation function, special three-dimensional rotating light for knife mold, 3D scanning system, fast autofocus, automatic zoom lens;

10. Contact probe measurement can be selected, and the software can freely realize the conversion of probe images to each other, which is used for contact measurement of irregular products, such as ellipse, radian, flatness and other sizes; You can also directly use the probe to dot and then import it into the reverse engineering software for further processing!

11. The image measuring instrument can also detect the roundness, straightness, and radian of round objects;

12. Flatness detection: the flatness of the workpiece is detected by the laser probe;

13. Professional measurement function for gears.

14. The special measurement function of the test sieve used by the major metrology institutes in the country 15. The comparison function between the drawings and the measured data.

At present, on the basis of the traditional imager, a new type of image measuring instrument has been developed: flash meter.

VX3000 series flash tester is widely used in machinery, electronics, molds, injection molding, hardware, rubber, low-voltage electrical appliances, magnetic materials, precision stamping, connectors, connectors, terminals, mobile phones, home appliances, printed circuit boards, medical equipment, clocks, knives and other fields can show their skills and use freely!

The flash meter can measure various 2D dimensions, such as length, width, angle, diameter, radius, circumference, pitch and other parameters.

Advantages of <> flash meter over traditional imager:

First: omit the link of clamping the workpiece and establishing the coordinate system, the measured workpiece can be placed in any position, just put the measurement object (can be a plurality of workpieces) on the coordinate table, press the one-key measurement button, you can quickly complete the multi-target and multi-size measurement in a few seconds.

Second, the biggest difference from traditional image measuring instruments is that they can automatically search and locate the product and detect and measure the contour of the measurement object within the range presented in the image covering a wide field of view.

Third: the one-button image measuring instrument itself is simple in structure, does not need displacement sensor grating ruler, through a large angle of view and large depth of field telecentric lens, the product outline image is reduced and then transmitted to the CCD camera with millions of pixels of high resolution for digitization, and then after the drawing software and the ruler are compared and processed to calculate the product size, and at the same time complete the evaluation of the size tolerance.

Fourth: In the past, the traditional measuring instrument had to manually move the x y coordinate table for measurement, resulting in the longer the measurement time required for the more measurement objects, and the one-button image measuring instrument does not need to manually establish the coordinate system, focus and repeatedly align and other operations, and the measured object will not be affected by the position and angle of placement, so the measurement time is greatly shortened, and the efficiency is improved by dozens of times compared with the traditional one.

Fifth: There will be no different measurement data due to different operators: when the traditional measuring instrument measures by observing the edge of the measurement position with the naked eye, it is easy to be affected by human influence to cause errors in the measured data, while the one-button image measuring instrument will automatically detect the edge of the workpiece, and anyone who can operate can measure stably and obtain the same measurement data.