iPad wifi won t turn on, automatically turn off, what s the problem?

1. You can try to turn on the airplane mode, and then turn off the airplane mode after 10 seconds. If the wifi switch is still gray, you can try a few more times.

2. If the airplane mode fails, try restarting your iPhone5.

3. If the reboot also fails, try to restore the settings of the phone. Open Settings - General - Restore. Try resetting your network settings.

If the wifi switch is still gray, you can restore it a few more times. You can also try to reset all the settings below. These may be caused by the iPad upgrading to the iOS system version (iOS has had WiFi bugs before).

If you have just upgraded iOS, these restoration methods may be able to solve the problem that the WiFi wireless LAN becomes gray and the switch cannot be turned on.

If you can't solve the problem of wireless LAN (wifi) not working, it is likely that the wifi module is physically damaged. For example, the wifi chip is in poor contact and so on. At this point, the only solution is to send it for repair.

The maintenance during the warranty period is free, and after the warranty period, the cost of repairing the problem that the wifi cannot be opened is about 350 yuan.

iPad2017 customer said that it had been repaired before, and now the wireless can't be turned on, and the Internet can't be accessed, see what the problem is.

It may be due to the following conditions:

1) There is a problem with the broadband that provides wifi hotspots, you can try to connect the computer alone;

2) If the broadband is normal, it may be caused by the wifi setting problem, you can reset the wireless network to try to connect;

3) Caused by mobile phone problems, you can change the phone for testing.

Try flashing the firmware again, anyway, it's a perfect jailbreak now. Wish.

The operation of the iPad to automatically connect to the connected WiFi is as follows:

1.Click "Settings" on the main filial piety interface.

2.Turn on Wi-Fi.

3.Select the name of the netsmith Li Fengluo that needs to be remembered, and enter the password.

4.Next time, just turn on "Wireless LAN (WiFi).""option, the iPad will automatically connect to WiFi.

What is the reason why iPad automatically connects to wifi and can't get online.

1. The WiFi itself is a problem, and the WiFi may not be connected normally, which will lead to the inability to access the Internet.

2. Router problems, the router may be overheated or damaged.

3. Broadband arrears may lead to inability to access the Internet.

4. The wifi name package contains Chinese, resulting in some mobile phones unable to connect to the Internet.

5. iPad system problem, there may be a problem with the system, resulting in connecting to wifi but unable to access the Internet.

If your iPad automatically disconnects from wifi after locking the screen, it may be because of the following reasons:1Low Power Mode:

In low power mode, the iPad will automatically disable some unnecessary features, including the WiFi connection. You can disable the option in the Battery option in the Settings app. 2.

Auto-lock time: If your iPad auto-lock time is too short, it may cause the wifi to disconnect automatically. You can adjust the auto-lock time in the Display & Brightness option in the Settings app.

3.WiFi Sleep Mode: iPad can put it into sleep mode when you haven't used WiFi for a long time.

This helps to save power. You can adjust the wifi sleep mode in the vibrato "Wi-Fi" option in the "Set up Eggplant Brothers" app. If the above methods don't work, try resetting your network settings.

In the Settings app, select General> Reset, > Reset Network Settings. This will erase your wifi network settings and restore it to factory settings, you need to reconnect to the wifi network and enter the password. I hope I can help the owner of the small dust pin Oh.

This is the function of the iOS system, when the screen is locked, in order to save power, the system will automatically turn off the wifi connection after the screen is locked, and it will be automatically connected after the screen is turned on.

Solution: If you don't want to automatically turn off the wifi function, you can click Auto lock in the iPad's settings, general, select never, and don't manually lock the screen when you don't play the iPad, so that the iPad will not lock the screen and will not disconnect from the network, but the disadvantage is that the power consumption will also be relatively higher.

Hello, this is because of Apple's own settings, when the screen is locked in order to save power, Apple will automatically cut off wifi. If you want to stay connected to WiFi all the time, you can set it up according to the following steps:

1. First find the connected wifi network and click on the exclamation mark at the end.

2. After clicking Go, slide to the bottom of "Auto", click: http**Auto, you can keep the wifi connection under the lock screen.

Extended Materials. Optimize your settings.

No matter how you use your device, there are two easy ways to save power: adjust screen brightness and use a Wi-Fi connection.

Dim the screen brightness or turn on auto-brightness to extend battery life.

1. To dim the brightness, open the "Control Center" and drag the brightness slider to the bottom.

2. The automatic brightness adjustment function will automatically adjust the screen brightness according to the lighting conditions. To activate this feature, go to Settings > General > Accessibility > Display Adjustments and turn on Auto Brightness.

When you're using your device to get data, a Wi-Fi connection is more power-efficient than a cellular network, so you can keep Wi-Fi on. To turn on Wi-Fi, go to Settings > Wi-Fi and connect to a Wi-Fi network.

The reason why the wifi will be disconnected after the ipad is locked is because the ipad is set to automatically disconnect the wifi in the sleep state, the solution: turn on the phone and tap the settings icon. Select the WiFi options bar.

Click on the option in the top right. Then select the Advanced Options Bar. Click on the Keep WiFi connection while dormant bar to do so.

It should be possible to set it, so look for yourself.

Summary. Hello dear, this may be due to the "Auto Lock" setting in the iPad settings. You can try turning off auto-lock in the settings, or adjust the time of auto-lock to make sure your iPad stays connected before auto-locking.

Hello dear, this may be due to the "auto-lock" setting of the image in the iPad settings. You can try turning off auto-lock in the settings, or guess the time of auto-lock to make sure your iPad stays connected until it's auto-locked.

The gray dot of the infinite LAN is not opened, and it will be automatically grayed out when clicked.

Because of the system limitation of the iPhone, the wifi will be automatically disconnected after the lock screen is long to save power. But there is no machine lock, after a short period of time, such as 2 minutes to 3 minutes, it will automatically disconnect the wifi, slide to unlock, and then it will be manually connected from the scumbag. After this problem occurs, if your home router is fine, it is generally caused by the mobile phone system or the third-party software installed.

Thank you This is usually due to the energy-saving settings on your iPad. You can try staring at the collapse in the settings, select "Screen & Lighting", and then change the "Energy Saving" setting to "Off". This should solve the problem and make the gray dot of wifi and unlimited LAN work properly.

After the screen is turned off, the screen is turned on again, and the network is broken. You need to shut down and restart to connect to the Internet.

Or click on the airplane mode, and then click on it, you can connect it. It's a hassle. Autojoins are invalid.

I'll check. 1.Check if the network connection is normal, check if the Wi-Fi signal strength is sufficient, and check if the router is working properly.

2.Restart the router to make sure the power supply and network cable are connected properly. 3.

Check for software blocking internet connections, turn off firewalls and malware, and try to reconnect to the internet. 4.Reinstall the network driver to ensure the correct operation of the network device.

5.Restart your computer and check if you can surf the Internet.

You don't need to use the software, just turn off the "wireless data" permission of the software in the settings.

Take ipadmini4 as an example, the operation steps are as follows:

1. Open the settings app on the iPad desktop, as shown in the figure below.

2. Click on the app to disable the network in the settings, as shown in the image below.

3. Click "Wireless Data", as shown in the figure below.

4. Disable the allowed data, as shown in the figure below.

The iPad takes a high-band channel, and it is recommended to change the channel of the wireless router to 11 or 13.

Or try to set a static IP for iPad, after setting a static IP, please click the wireless LAN button or the wireless Wi-Fi button in the upper left corner to make the static IP take effect.

1. Turn off the wifi and turn it back on.

2. Restart the phone and try it online.

3. Restart the wireless router and try it.

4. Set up the wireless router again.

Connection: 1. The network cable on the wall (that is, the broadband network cable) is connected to the WAN interface of the router.

2. If you have a desktop computer to access the Internet, please buy another network cable from the other interface number of the router (interface, etc.) to connect to the desktop computer, in the network settings of the desktop computer, select Automatically obtain the IP address (if you can't do this step, please ask me again).

3. If you need to access the Internet on a laptop or mobile phone, you can directly search for wireless signals, find your router name, enter the password you set, and you can access the Internet. (In general, as with desktops, IP addresses should be automatically obtained.)

Configuration of the router:

1. Open the browser, and enter it may also enter the router configuration interface. In general, the login and password are admin.

2. There should be a configuration wizard on the left side, click on that and follow the steps step by step.

3. If there is no configuration wizard, then configure each item yourself, you must configure the "network parameters" and "wireless parameters", and there should be no problem if you configure it, if you need wireless Internet access, then please pay attention to whether your router has the wireless function turned on.

The steps to be aware of are:

1. Please select the correct connection method in "Zen Zheng Network Parameters", if you want to broadband it is generally PPPoE dial-up, there are other ADSL, dynamic IP, static IP, etc., if you choose the wrong one, it will lead to failure to connect. If you're not sure which way to go at home, call your broadband company and ask.

2. Please write the Internet (broadband) and password correctly in the "network parameters" (if you forget, please contact the broadband company to ask for the password), please note that this password is not set by yourself, but when you buy broadband, the broadband company gives you, if this is written wrong, it will lead to being able to connect to the router, but you can access the Internet normally without being around the world (the common feature is that the IP address is all.

3. In the "wireless parameters" (it may also be called something else, I can't remember clearly), please enter a password to connect to the router, this is set by yourself, used to connect to the router, if you don't set this password, then anyone (provided that you can search for your network signal, such as your neighbors) can connect your router to surf the Internet, which is the so-called "rubbing the net", which will affect your network speed. If you forget this password, you can reset it in "Wireless Parameters".