The laptop is silent when it s used, and there s no sound when the laptop is used

How to install the sound card driver.

First of all, let's check whether your machine's sound card driver is normal.

Method: Open my computer, right-click on Properties, Hardware, Device Manager, and see if there is an icon with a yellow question mark.

If there is one, it means that the hardware driver is not working properly or there is no driver at all.

If the motherboard has an integrated sound card, use the sound card that comes with the motherboard to drive the CD installation.

Double-click the setup icon, if there is no icon, my computer right-click Properties Device Manager to find the location of the sound card, right-click Properties Driver Update Driver to find the file where the sound card driver is located is generally an inf file Double-click, next, you can. There is no drive, go to the next drive house.

The first thing to know is the model of your sound card.

Then use software such as Super Bunny or Optimizer to check out his model.

It must be the same model, if not, find a Massmut sound card driver and install it.

If it is a discrete sound card, first turn off the sound card integrated with the motherboard in ComOS and install it according to the steps above.

Resources. If it doesn't work for you! You try this method again and check the registry.

This ** indicates that the registry returned an unknown result.

To resolve this issue, follow the recommended solution, and it will run. If that doesn't fix the issue, type "scanreg restore" at the command prompt (without double quotes). Finally, remove the device from Device Manager and re-detect it using the Add New Hardware tool in Control Panel.

If you can't do it, then you have to reinstall the system.

Uninstall the sound card driver completely, and then install the driver. If the deletion is not clean, it is recommended that it is better to redo the system.

That's because your computer's sound card driver is not suitable, you can find it in the boot startup item to let it boot up, and I was like that before. If it doesn't work, you can update your computer's sound card driver.

Because the headphones are connected, the computer can't send out the sound from the speaker and the headset at the same time, there is a sound when it just starts, the computer driver is not loaded, only the speaker is recognized, and after the driver is loaded, the system knows that you plugged in the headphones, and the sound is transmitted to the headphones

If your book is.

with the Vista system.

And the sound card chip is IDT

The 5939 version is used for the driver.

After a short time after turning on the machine, there will be a silent phenomenon.

It is recommended to change the driver back to an older version.

Because of my gateway

T 6824c is updated to the latest version 5939 driver is this state, and changing back to the old version of the driver can solve this problem.

It's okay, the staff will help you see if it's a driver problem, if not, you ask the seller to change, the problem is not very big.

Go to him to change it, but be careful when you change, don't be changed by the merchant for a different model or something, if he changes you to another model, you must pay attention to it.

Horn circuit problems, go to the warranty.

It's nothing to bother with, you didn't buy it for a few days, it's adjustable and exchangeable.

With the new driver, if it is not good, then check the motherboard capacitor after sales to see if there is a bulge.

Turn on the power and press the F8 key to enter the safe mode with the network, and use the driver wizard to update the sound card driver.

If it can help you, I hope you will adopt it with a star review!!

Not much to say, the system is pirated, right?! Install a genuine system, or update the driver!

One is that your driver is going to be updated,,, and the other is that the XP system is not installed or not genuine,

It should be that your sound card driver is not installed.。。 You go to the Internet and find a sound card driver of your model and try it.

That's because when you close the screen, it's on standby, which is normal for all laptops.

However, it can be changed in the power management.

In the power options in the control panel, set the function of closing the lid and set it to not take any action, but I don't know if this is good for the computer.

You can go to the power options in the control panel and set it yourself. It's simple.

You can set the control panel - Power Management to turn off only the display, not standby.