What to do if the mouse of the notebook does not respond

If the mouse of the laptop does not respond, you can see if your driver is installed, see if your cable is connected, and see if your mouse has power.

The mouse of the notebook is not responding, the first one is to check if it is connected to the bit, and the second one is to look at the interface.

If your mouse does not respond, it may be that you plugged it in badly, or it may be that your mouse has been calculated, and it is best to plug it in again. Press it.

If the mouse of the laptop does not respond, it may mean that the mouse is broken, so in this case, you can go to the place where the computer is sold to repair it and have a look.

If the angle of the mouse on the laptop does not respond, it is possible that your mouse is broken due to a problem, or because its control circuit is broken.

The laptop mouse does not reflect, this should be impossible, unless the mouse is broken, or the power interface of the mouse is broken and does not power on.

You can restart the computer and try again, there may be a problem with the system.

Probably, the installation of the mouse is not yet complete.

1.This may be due to accidentally turning off the touch screen, generally press fn (function key) + f6 (different keys for different notebooks, there is a touchpad image on the button) to unlock. Some computers also have buttons that open and close the touchpad directly.

2.Next, you can check if there is a problem with the driver. If you have reinstalled your computer, you should install the appropriate driver before trying to enable the touchpad.

Secondly, there is the issue of settings. Open the properties of the mouse in the control panel, you can see that there is a device setting value clicked, you can see that there is a setting value on the interface that comes out, and an interface comes out after clicking, and you can see that there is a touch on the left side of the interface, and there will be an enable touch on the right interface, and you can click to select it.

3.If there is still no response, it may be a hardware problem with the touch screen. However, since the touch screen is rarely broken, it is finally necessary to contact the relevant repairer after-sales service to deal with it.

Enter and click OK in the input box that appears for the new task, and your desktop will reappear and your desktop mouse will be available again.

What should I do if the win7 computer mouse clicks on the desktop icon and does not respond? Some users reported that it is normal to turn off the computer, and there is a problem when the computer is turned on again, the mouse can move, but there is no response when the mouse clicks on the computer desktop icon. What's going on?

What should I do if the computer mouse clicks on the desktop icon and it does not respond?

Reason 1: Win7 desktop Windows Explorer stops working.

Computer mouse click on the desktop icon does not respond Solution:

1. Press CTRL+Shift+ESC to bring up the Windows Task Manager window, and find the process of "Explorer" in "Processes";

2. Select the "Explorer" process, right-click to select End Process, find "File" in Windows Task Manager, and select "New Task" under the file;

3. Enter "explorer" in the pop-up new task window, and click OK to reopen the explorer and rebuild the cache!

Cause 2: There is a virus in the win7 computer.

Computer mouse click on the desktop icon does not respond Solution:

1. Open Windows Explorer, check the abnormal process, if there is a process that occupies a lot of CPU, it may be caused by a virus or Trojan horse, right-click to select the end process to end the abnormal process:

2. Then use anti-virus software to scan and kill the computer for viruses, and the mouse icon still does not respond after restarting the computer, it is recommended to reinstall the computer system.

Storage), detect and kill malware. 3 The computer configuration is poor, try to set the virtual memory to a larger one, (xp) right-click on my computer Properties Advanced Performance ......There Settings Advanced Change in Custom There Set to 2000 - 4000 (Win7) Computer - Properties - Advanced System Settings - Performance Settings - Advanced Tab - Virtual Memory - Change - Select the drive you want to set C, select the system management size or select the custom size as you need - Settings - OK. 4 Antivirus software installation takes up a small amount of resources, such as NOD32, or only one auxiliary antivirus software is installed.

5 Try to set the IP to a static IP, which can reduce the startup time of the computer and the reflection time after entering the desktop. 6 Don't put too many files and icons on the computer desktop, which will slow down the computer's response, and try not to install the software on the C drive. 7 Close some startup programs.

Start-Run-Enter msconfig-OK-Click "Start" in the "System Configuration Utility" window-Start, except for the input method (ctfmon) and anti-virus software, the general program can be turned off. You can also use 360 and other software to intelligently optimize boot acceleration. 8 It is recommended to install only one main antivirus, as installing multiple will take up computer resources and make the computer slower.

9 Regularly defragment the disk, open my computer To defragment the disk of the drive - Properties - Tools - select the defragmented disk to open the "Disk Defragmenter" window - Analyze - Defragment - the system will start to defragment. 10 Install a computer optimization software such as Optimizer or Super Rabbit, and the computer will be much faster under optimization!! 11 The current system also occupies a large amount of memory, and if necessary, adding more memory will be much faster.

12 The computer hard disk will be used for a long time, it will also make the computer slower, repartitioning and installing can fix the logic is bad, the computer will be faster, the physical read and write speed of the hard disk is slow, and it can only be changed to a better point!

1. When the desktop does not respond, first open the explorer (Ctrl+Alt+del). 2. Once you are in the explorer, select the Process option. Find the explorer process in the process window and click End Process below.

3 After the end, select.

Summary. 1.The touchpad function is turned off, re-open the touchpad function through the shortcut key, find the touch version icon, and press the FN+ shortcut key.

Search for the trackpad in the control panel, turn on the trackpad function in the trackpad, search for the trackpad in the control panel, turn on the trackpad function in the trackpad, or notice whether the trackpad will be connected to the mouse in the trackpad, keep the trackpad open, this function is checked.

2.The trackpad driver is incorrect, right-click on this computer and select Properties to open Device Manager and select Mouse.

3.If the touchpad components are damaged, hand them over to professional maintenance personnel for repair.

What should I do if my laptop mouse click doesn't respond?

Hello, dear, I will answer this question for you, and please wait patiently Oh h 1The touchpad function is turned off, re-open the touchpad function through the shortcut key, find the touch version icon, and press the FN+ shortcut key. Search for the trackpad in the control panel, turn on the trackpad function in the trackpad, search for the trackpad in the control panel, turn on the trackpad function in the trackpad, or notice whether the trackpad will be connected to the mouse in the trackpad, keep the trackpad open, this function is checked.

2.The trackpad driver is incorrect, right-click on this computer and select Properties to open Device Manager and select Mouse. 3.

If the touchpad components are damaged, hand them over to professional maintenance personnel for repair.

The touchpad can be used.

You can connect a mouse to see if it can be used.

It's just that the mouse can't be used.

Your touchpad is not turned off.

There is no wired mouse now.

The touchpad can be used.

Just now the mouse could be used, but suddenly it can't be used.

The touchpad driver has been corrupted or accidentally uninstalled.

You force the shutdown and turn it on again.

Press and hold the power button for ten seconds to force the power to shut down.

If the mouse is not responding, it may be that the system is not.

There is a correct identification or damage to the mouse itself.

Bad, it may also be a mouse interface loss.

Bad. If this happens, you can.

Open Device Manager to uninstall the current one.

of the mouse driver, re-insert the mouse.

tag for the system to re-identify when installed.

before the mouse drive. If you can't.

Recovery, consider the notebook interface.

Problems or damage to the mouse itself, will.

Plug the mouse into another computer for testing.

Whether the mouse is damaged. Judge by this.

Check whether the interface is normal.

Personal advice, remember.