How to clean the fan without dismantling? How to disassemble and clean the electric fan

The method of cleaning the fan does not need to be disassembled. The fan wants to be clear and not have to be disassembled. Then you can take a damp rag.

Dip in detergent. Don't screw it too dry. Then wipe it where the electric fan has dust.

Finally, throw the rag with clean water, wring the whole out, and wipe the electric fan again. Dry it and you're good to go.

If you don't want to dismantle the fan, then the best thing to do is to let him keep spinning, or you can take a hair dryer to dry the dust for him, maybe for a long time.

The disassembly and cleaning method is as follows:1. First of all, break the chuck of the protective mesh in the clockwise direction, as shown in the following figure:

2. Remove the front mesh cover of the electric fan after loosening, as shown in the figure below

3. Then unscrew out the shaft nut, as shown in the figure below

4. Then take out the fan blade, as shown in the figure below

5. After loosening, the net nut is manually screwed out, as shown in the following figure

6. Finally, take out the back net, as shown in the figure below

Preparation materials: watering can, baking soda, white vinegar, washing spirit, water appropriate amount of cleaning method:

1. Prepare a container.

2. Pour in an appropriate amount of baking soda, white vinegar and detergent.

3. Add a little water and stir evenly into a solution.

4. Pour into the watering can and screw the cap.

5. Spray the prepared solution on the electric fan (avoid the power supply) and wait for a few minutes to dissolve the dust.

6. Turn on the fan and rotate it for about 10 minutes, and the wind will blow away the stains that have dripped down.

7. There is no need to disassemble the electric fan, the dust on it has been cleaned.

Cleaning the electric fan is so simple, no dismantling, no unloading, no washing, one spray of rapid dust removal is cleaner.

Wrap the switch in a dry towel, then spray Mr. Vermeer, and after ten minutes use the shower head to flush, the amount of water should be large, let the fan leaf turn up, and repeat it a few times.

Here's how:

Tools: electric fan, brush, compressed air, cloth.

1. Turn off the fan. Unplug the power switch from the fan or turn it off from the wall. Before cleaning the fan, make sure the blades stop turning completely.

2. Vacuum fan holder and safety net. Connect the vacuum's accessory brush to the end of the vacuum hose and turn on the vacuum. Slide the vacuum hose onto the fan to absorb accumulated dust and dirt. Clean from top to bottom.

3. Spray compressed air on the blades of the fan. Buy a can of compressed air. Thread the straw through the sheer and press the switch on the can to expel the air from the straw.

Blow on each blade of the fan until they are free of dust. When spraying, place the compressed air tank face up.

4. Wipe the fan with a microfiber cloth. Start at the top of the fan and wipe back and forth. Wipe down the protective mesh, base, and back of the fan. Do this once a week to keep the fan clean.

A few precautions for cleaning the fan:

1. When cleaning the fan, it is best to unplug the power supply, and then wipe it with a soft cloth, and wipe it with a damp soft cloth for the marked places, but do not clean it directly with a large amount of water.

2. There is no need to disassemble the fan for daily cleaning, but it is still necessary to disassemble and clean it after using it for a long time, mainly for the cleaning of the internal motor, so as not to affect the normal performance.

3. The leaves of the electric fan are usually plastic, so it is generally possible to carefully wipe off the dust and dirt with a sponge dipped in detergent.

Electric fan cleaning tips can only be wiped with a rag if you want to clean it, the method of Tongwu is as follows:

1. First of all, break the chuck of the protective mesh in the clockwise direction, as shown in the following figure:

2. After loosening, take the mega wheel and change the front mesh cover of the electric fan, as shown in the figure below

3. Then unscrew out the shaft nut, as shown in the following family judgment drawing:

4. Then take out the fan blade, as shown in the figure below

5. After loosening, the net nut is manually screwed out, as shown in the following figure

6. Finally, take out the back net, as shown in the figure below

If the electric fan is dirty, the cleaning steps are as follows:

Material preparation: vacuum cleaner, cloth, etc.

1. Turn off the fan and the dust is eliminated. Unplug the power switch from the fan or turn it off from the wall. Before cleaning the fan, make sure the blades stop turning completely.

2. Vacuum fan holder and safety net. Connect the vacuum's accessory brush to the end of the vacuum hose and turn on the vacuum. Slide the vacuum hose onto the fan to absorb accumulated dust and dirt. Clean from top to bottom.

3. Spray compressed air on the blades of the fan, or you can use a small pump. Buy a can of compressed air, thread the straw through the net and press the switch on the can to expel the air from the straw. Blow on each blade of the fan until they are free of dust.

When spraying, place the compressed air hose face up.

4. Wipe the fan with a microfiber paichi cloth. Start at the top of the fan and wipe back and forth. Wipe down the protective mesh, base, and back of the fan. Do this once a week to keep the fan clean.

How electric fans work

In addition, low-power motors such as DC motors and brushless DC motors are increasingly widely used in small fans.

When the electric fan is working (assuming that there is no heat transfer between the room and the outside world), the temperature in the room will not only not decrease, but will rise. Let's analyze the reason for the temperature increase: when the electric fan is working, because there is an electric current through the coil of the electric fan, the wire is resistive, so it will inevitably generate heat to release heat, and the temperature will naturally rise.

Because there is a lot of sweat on the surface of the human body, when the electric fan is working, the indoor air will flow, so it can promote the rapid evaporation of sweat, combined with "evaporation needs to absorb a lot of heat", so people will feel the coolness of the feast.

Soak the removed fan mesh in a basin with dish soap solution for 3 to 5 minutes. Then use a damp rag soaked in dish soap solution to clean the protective net inside and outside until all the dirt on the surface of the protective net is cleaned, and finally wipe it dry with a dry rag. A little thicker is fine.

Put the fan cover and fan blades in the mixed washing water, soak for 10 minutes, and then use a small brush (old toothbrushes can buy a bottle of foam car wash liquid to clean the interior of the car, spray it, and then wipe it with a wet towel. Brush off the greasy dust, rinse it with water, dry it with a towel, and dry it.

Wipe the front of the child clean. Wipe the back again, while wiping, turn the fan blades with your hands, wipe both sides of the fan blades, then clean the rag, and wipe again with a clean rag. Then wipe the grille behind the fan, the rod and the disc underneath.

Remove the electric fan protection net, scrub the fan leaves and various parts with laundry detergent water, before this must be powered off, must not be charged as the net cover of the electric fan is removed, I am using our kitchen oil cleaner, spray a small amount on the whole and leaves of the electric fan several times, the oil stain foam form slides to the ground, and after drying, it can be powered on, and the cleaning effect is still very satisfied. Karma. Then clean the protective net, be sure to wait until all parts of the fan are dry before powering on.

Take a semi-wet towel again, wipe the other undisassembled parts of the electric fan, in the wiping process, just pay attention to the water does not unplug the electricity first, and then disassemble it, and then use water, dish soap, add some vinegar, it may be better to wash a little, wash it well, dry it, and when not in use, do it once first. After unplugging the power supply, first put it outdoors in a wide and ventilated place, use a hair dryer or hair dryer, and pay attention to keeping a certain distance, so as to blow down the main dust deposited on the fan. Then you can install it, you have to wet the part of the motor behind the electric fan, and clean it strongly.

What should I do if the electric fan is too dirty? Teach you a little trick to wash it without dismantling or unloading.

If this is floating ash, you can use a hair dryer to blow it clean, if it is not floating ash, if you still want to wash it clean, it is recommended to remove it, because it may be washed cleaner after disassembly.

First prepare a container and add some wind oil essence to the container, after adding it, we add some baking soda, then add salt, and finally add some white vinegar, stir evenly, mix almost, then add some water to dilute it, and finally pour it into the watering can, and then the fan that has not been cleaned for a year at home has a lot of stains on it, as well as dust, at this time, you can spray the prepared solution on the fan, the front and back should be sprayed, and then we turn on the fan, Remember to put the fan in an open area to blow. After blowing for ten minutes, you can see that the stains on the fan blades and the dust have disappeared, this is because baking soda has an inclined effect, which can clean the stains on the fan blades well, and the acetic acid in the white vinegar has a softening effect, which can soften the stains on it. In the process of fan blowing, the stains on the fan can be blown off very well, the salt is granular, which can well remove the dust on our fan, and the salt can be well sterilized and disinfected, so that there will be no bacteria on our fan.

1. First of all, you need to prepare a container, put baking soda, dish soap, add a little white vinegar, add water to dilute evenly, and then prepare a watering can and pour it in.

2. Next, spray a few times on the fan with a watering can, the front fan blade and the back fan blade must be sprayed, and do not let go of any small parts.

3. Then we can prepare a brush, for some places that are difficult to reach, we can prepare a toothbrush. Baking soda and dish soap have a very strong decontamination ability, which can effectively remove the dust of the fan and other microorganisms, while white vinegar has the effect of softening the dirt, so the whole cleaning process will be relatively simple.

4. After cleaning, prepare a basin of clean water, wipe the electric fan with a clean rag, wipe the blades of the electric fan and the body of the electric fan, including the base, and finally wipe it dry with a clean rag.