How to disassemble the air conditioner for cleaning, how to remove the air conditioner for cleaning?

How do you remove an air conditioner? How to disassemble and assemble the air conditioner.

1. The first thing we need to do is to clean the outside of the air conditioner, the cleaning of the air conditioner is relatively simple, we only need to open the cover of the air conditioner, and then use a wet rag to wipe the exposed shell. When we wipe, we must pay attention to some corners that are not easy to see, because some corners that are not easy to see are the most dirty.

2. After cleaning the external unit of the air conditioner, we will clean the filter of the air conditioner. After we turn on the air conditioner, we can see the air conditioner filter, at this time we can clean the air conditioner filter, soak the air conditioner filter in the air conditioner cleaner, and then take it out after a period of time, rinse it with water, and wipe it carefully. In general, it is relatively easy to remove the substances attached to the air conditioner filter.

3. The last step is to clean the air conditioner radiator, we can use a professional air conditioner cleaning agent to spray the air conditioner radiator up and down two to three times, so that the air conditioner can be more uniform, and wait for three to five minutes to turn on the air conditioner and operate, so that we can work for 20 to 30 minutes, and we can thoroughly clean the air conditioner radiator.

The method of disassembling the air conditioner hangs up is as follows:Equipment: Old-fashioned Changhong air conditioner.

The first step is to lay the air conditioner flat on the table, as shown in the figure below

The second step is to open the front panel of the air conditioner, as shown in the figure below

The third step is to pull out the panel from one side to remove it, as shown in the figure below

The fourth step is to pull the frame outward from one side to remove the outer frame, as shown in the following figure

The fifth step, shake and remove the air inlet to complete the removal of the outer cover, as shown in the figure below

Step 6: Complete the diagram, as shown in the following figure:

Dismantle the machine, open the machine to cool, the temperature is reduced to a minimum, and the shutdown is prevented.

Second, tighten the thin tube, that is, the high-pressure pipe, with an inner angle, and then close the thick pipe after about 60 seconds, that is, the high-pressure pipe {that is, fluoride).

Third, remove the external cable.

Fourth, the rest is up to you, as long as you don't flatten the copper pipe.

Xi'an Shuangsheng Hongfuda Moving Service Department has a group of young and professional employees, all of whom have undergone strict professional training and are proficient in the packaging and disassembly of items. "Don't ask for the most vehicles, but ask for the best service. ”

It is our service concept, "customer first, service first" is our commitment to the society.

Install one, first install the inner machine.

Second, install the external machine again.

Third, connect the thick and thin tubes. Open the coarse pipe gate, and then unscrew the thin pipe nut a little.

At this time, there will be air coming out, (i.e., the air exhausting from the internal machine) when the air comes out.

When it gets cold, it comes out with fluorine. At this point, tighten the nut.

Fourth, open the thin pipe gate with an inner corner. At this time, the air conditioning duct is a circulating circuit.

Fifth, connect the power cord and control cable with the external unit.

Everything is OK, power on the test machine.

For high-altitude operation, it is recommended to call in a professional. Although the operation is simple, the high-altitude operation is not fun.

If the machine is disassembled in winter, it cannot be refrigerated, and then the four-way valve line of the external unit is thrown off, and it will be refrigerated, that is, the fluoride can be collected normally.

Or take out the temperature sensing head of the internal machine and put it in a glass of warm water, which can also achieve normal cooling in winter. But I'm used to using it personally.

The former approach. However, the four-way valve wire that is thrown off is live, so be careful not to get electric shock and not let it touch the casing. Operate with electricity, wrap it with tape and you're foolproof.

Hope it helps

1. Disconnect the power supply of the air conditioner and open the cover of the radiator.

2. Take out the filter screen on the radiator for cleaning.

3. The next thing is to clean the heat sink, which has more dust than the filter dust.

5. Remove the cover from the radiator and prepare the spray device. Try to use a special cleaning spray for cleaning air conditioners, and if you don't have one, you can make one yourself.

6. Find a mineral water bottle, make a few small holes in the bottle cap, fill the bottle with water, put in the detergent, shake well and set aside.

7. Wipe the dust on the surface of the air conditioner with a rag first, and then use a spray to clean the radiator from top to bottom.

8. After cleaning, install the filter screen, turn on the refrigeration and drain the unclean things in the radiator.

The most you can do to clean the air conditioner by yourself is to open the air conditioner shell, take out the dust filter, wash and dry, and then wipe all the places you can see to dry. Use one and find someone to clean the pipes or something, and that's two hundred cheaper.

1. First of all, in order to prevent electric shock and leakage, you need to turn off the power socket, or you can directly unplug the socket, which is very important;

2. Then open the shell of the air conditioner upwards, with a very light force, special attention should be paid to the fact that if you find that it is not easy to open by hand, you can use a screwdriver to help, do not use brute force, you must master the skills, otherwise it is easy to damage the shell of the air conditioner;

3. After opening the shell, the inner shell is raised above the air conditioner, and the air conditioner shell can be automatically stuck and fixed, so you don't have to worry about falling off; At this time, you can see that there is a plastic air conditioning filter inside, which is the part that loves to hide dirt and dirt;

4.You only need to gently push the filter up with your hand, and then remove the filter screen;

5 Put the strainer in the basin and rinse it directly with water.

6. Then add an appropriate amount of warm boiling water to the basin and soak for an hour, as shown in the figure below;

7. After an hour, clean the filter with clean water;

8. Finally, put the cleaned filter on the balcony to dry.

Here's how:

1. First unplug the power supply of the air conditioner to prevent electric shock during the cleaning process.

2. After that, buckle the air conditioner cover on both sides and remove it.

3. After that, use a screwdriver to unscrew the screws on the air conditioner housing.

4. In this way, the air conditioner shell can be disassembled.

5. After that, remove the filter on the air conditioner.

6. After that, use plastic cloth to cover the air conditioner to prevent the wall from being soiled by cleaning.

7. After that, use a watering can to spray the cleaning agent inside the air conditioner.

8. After that, use clean water to rinse the air conditioner.

9. The outer panel and filter element of the air conditioner are also treated in the same way.

10. In this way, the air conditioner will be cleaned.

First, unplug the socket on the air conditioner unit and make sure that the air conditioner unit has no power before proceeding to the next step.

Facing the indoor hang-up of the air conditioner, on both sides of the hang-up, you can find a small recess, one on the left and one on the left and one on the left.

Then break one side with your hand, break it out with a small force, and break the other one in the same way. In this way, the plastic casing of the air conditioner is opened.

Pulling out the filtered sea surface from the inside, I found a lot of dust piled up on it. Take it to the bathroom and clean it once with a small brush, and finally use laundry detergent once.

Shake the filter panel a few times and there are no water droplets, then put it back into the air conditioner and close the lid.

Finally, I found a moist towel and cleaned the outside of the air conditioner, which was very simple.

PS: It is best to clean the air conditioner 2-3 times. Usually, the air conditioner is cleaned once before it is turned on, and it is cleaned once during the middle of the air conditioner start-up.

Tips for life: Remember to do these things before using the air conditioner in summer, and be kind to yourself! It turns out that there is so much dust in the air conditioner, remember to remove it and clean it before using it! How to live in summer, air conditioning, cleaning dust, tips.

After the air conditioner is used for a long time, a lot of dirt and bacteria will accumulate inside, which will not only affect the operation effect of the air conditioner, but also reduce the service life of the air conditioner, so it is necessary to disassemble and clean the air conditioner regularly, so how to disassemble and clean the air conditioner? Let's learn together.

1. If you want to disassemble the air conditioner for cleaning, then you should unplug the power plug of the air conditioner first, so that the air conditioner is in a safe state of power failure. Then prepare relevant disassembly tools and cleaning tools, such as: special air conditioner cleaner, rags, high-pressure water guns, screwdrivers, etc.

2. When disassembling and cleaning the air conditioner, it must be operated in strict accordance with the disassembly and cleaning steps introduced in the instruction manual of the air conditioner. Each air conditioner will be equipped with an air conditioner instruction manual, which will generally introduce in detail about the disassembly and maintenance of the air conditioner, as long as the operation is carried out according to the operation steps introduced in the manual, there will generally be no problems.

3. When disassembling and cleaning the air conditioner, the shell and filter of the air conditioner should be removed first. When disassembling the air conditioner shell, you should buckle both ends of the air conditioner shell with both hands at the same time, and then pull the air conditioner shell out of an angle with a little force, and then gently buckle the two buckles inside, and then you can remove the air conditioner shell.

4. Next, the filter screen should be disassembled, the filter screen is generally stuck by several card slots, you should first push the filter screen up, let the lower end of the filter screen out of the card slot, and then gently drag the filter screen down, and generally you can remove the filter screen.

5. Then you should use a special air conditioner cleaner to clean the shell and filter of the air conditioner. When cleaning the filter, you can use a soft brush to continuously clean it, but you must be careful not to bend the filter. Then use a high-pressure water gun to rinse the casing and filter of the air conditioner.

After the filter is cleaned, it should be placed in a ventilated area to dry.

6. When cleaning the inside of the air conditioner, you can use a watering can cleaner for cleaning. First spray the watering can cleaner inside the air conditioner, and the watering can cleaner will produce a lot of foam, attached to the inside of the air conditioner, then you need to wait for about five minutes, let the foam dissolve the dust and dirt accumulated inside the air conditioner, and then use a rag to wipe the inside of the air conditioner continuously, and finally use a scraper to clean up the residual foam.

7. After the inside of the air conditioner is cleaned, install the air conditioner filter back, and when installing, do not install it in the wrong direction, and install it correctly according to the position of the buckle. Then install the air conditioner shell back, and finally use a rag to wipe the air conditioner shell clean.

The above is a detailed introduction to how to disassemble and clean the air conditioner, if you want to disassemble and clean the air conditioner, you can learn more about it, it is recommended that you should operate according to the disassembly and cleaning steps introduced in the instruction manual of the air conditioner, so as to avoid problems.

1. First of all, open the front cover of the air conditioner: pick both ends of the panel with both hands at the same time, and then pull the panel apart at an angle with a little force. 2. After opening the outer cover of the air conditioner, there are often two buckles inside, and it is necessary to gently open the outer cover to fully open.

Then it is to take the filter, the filter is relatively easy to take, but it is stuck by a few card slots, first push the filter up, and then gently drag the filter down after the card slot. 3. Then carefully rinse the filter with clean water several times, you can scrub it with a soft brush several times, and finally dry it in a ventilated place until it is dry. Be sure not to bend the filter when cleaning, although it is elastic, but the plastic one can not withstand bending.

4. When installing the filter, you need to pay attention to the wrong direction. It is very important to install it correctly according to the bayonet position above. After installing the filter, cover the panel, press it hard, and the installation will be successful when you hear a "click".

Based on the respondent's experience;

1. First of all, turn off the electric power source socket. It is best to unplug the socket directly, which is very important to avoid electric shock and leakage accidents.

2. Open the two ends of the shell of the water air conditioner, with a small amount of force, if you can't open it by hand, you can use a screwdriver to help, you need to master the skills, otherwise it is easy to damage the shell.

3. Open the shell, and then know that the stove will lift the shell above the water air conditioner, which can be automatically stuck and fixed, so you don't have to worry about falling off and dressing up.

4. You can see that there are 2 plastic frames inside, one on the left and one on the left. Inside this frame is the fiber mesh, which is the part that filters the air conditioning air and hides the dirt the most.

5. Gently push up with your hand, remember that a frame has 2 places to fix, and you need to push up on both sides. Remove the filter.

6. Take it to the toilet or have a water source. place, place on the ground, rinse directly with water, and then gently brush a few times with a brush.

7. Finally, use laundry detergent, or add with detergent, and then brush with a brush a few times, and finally it is very clean, use a clean dry rag to absorb the water, and there is no need to deal with it too dry, there is no problem.

8. Finally, according to the above method, in turn, push down, stuck, and finally close the water air conditioner shell is completed.

Hope it helps!