Where is the igniter of the gas stove and what are the ignition methods of the gas stove?

The gas stove igniter is mainly composed of a power supply, an ignition coil, a distributor, an ignition switch, a spark plug, an additional resistor and its short-circuit device, a high and low voltage wire, and other parts. The ignition needle is easy to be dirty, the kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the gas stove is placed for too long, the ignition needle is easy to be stained by oil, then you need to clean the ignition needle grease, and then try to ignite. The ignition needle is not in proper position, if you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, once the distance deviates too much, it will cause the gas stove to not ignite, generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it is necessary to aim at the fire hole.

As we all know, anything will be damaged to varying degrees after being used for a long time, and gas stoves are no exception. So the question is, how to change the ignition of the gas stove? Let's take a look.

How to change the ignition of a gas stove.

1. Remove the stove of the gas stove first, and then remove the cover on the outside, and ensure that the top is clean.

2. Then unplug the power supply and remove the strut of the switch.

3. Slightly erect the gas stove, loosen the screws on it, open the sealing cover, and then put the tempered glass on it.

The panel is removed. 4. Finally, remove the old igniter and replace it with a new igniter.

Note: At this time, the line should be connected, and finally test it to see if it can ignite the fire, if it can, it means that it can be used normally, sometimes the ignition needle only produces a little spot, we might as well take the rust remover.

Removal, followed by a few drops of lubricant, is not mandatory to replace.

Precautions for the use of gas stove igniters.

1. Because the power pool of the igniter is installed in the shell, the battery should be installed as much as possible before being installed on the stove, and only the rear cover plate needs to be opened when the battery is replaced.

2. Because the output voltage of the ignition is very high, the hand should not touch the discharge needle during the process of touching the button to avoid high voltage.

If it touches the human body, if it is unfortunately touched, it will not cause life-threatening danger.

3. The relative distance between the discharge ignition needle and the fire hole of the burner should be just right, and ensure that it is reliable, and if it is loose, it needs to be adjusted in time to ensure its ignition success rate.

4. Replace the ignition needle of the gas stove as much as possible to find the manufacturer's after-sales personnel to come to the door, and the length, height and distance between the ignition needle and the fire cover purchased outside are not suitable.

The gas stove switch, the one that can be rotated left and right, has two words to indicate the switch, and some need to press down and then rotate left or right.

When people are on lighters, they can use lighters to order things, but we have a lot of games in lighters, games, if you fall the ground, it will be **, we have to pay attention, pay attention when you use it.

Gas stoves refer to kitchen utensils that are heated by direct fire with gaseous fuels such as liquefied petroleum gas (liquid), artificial gas, and natural gas. Gas stoves are also called gas stoves, stoves, stoves, and stoves, and their popularity is well known, but it is difficult to see a common concept. So what are the ignition methods of gas stoves?

1. There are two ignition methods of gas stove: electronic pulse ignition and piezoelectric ceramic ignition. Electronic pulse ignition consumers are generally very familiar with the ignition device used in most embedded stoves, which is ignited when twisted to a certain position, which is very simple and convenient, and the ignition hit rate is high, generally 100%, but this way requires battery replacement.

2. Piezoelectric ceramic ignition is mostly used in desktop stoves, and the biggest advantage is that no battery is required. However, the success rate of ignition is related to the ambient humidity, and it is not easy to ignite when the humidity is high.

3. In addition, you need to press and hold the switch to ignite when ignition, which is not as fast as electronic pulse ignition.

How to turn on the gas stove

1. Unscrew the gas valve counterclockwise first, when the valve handle and the intake pipe are in the same line, the valve is open.

2. Then find the switch on the gas stove, press it down gently with your hand, and turn it counterclockwise after 2 seconds, then you will hear a snapping sound, and the gas stove will be turned on, as long as the fire is adjusted to the appropriate position.

3. Pinch the switch with your hand and turn it clockwise, wait for the fire in the stove to go out, then let go, and finally close the valve.

The correct way to turn on the gas laughing field stove

Turn on the gas source switch clockwise, then press down the knob of the gas stove and rotate it counterclockwise to 90°, then you will find that the ignition is successful and the flame burns normally.

If the flame can't stand, it may be that the knob is held down for less time, and then operate again immediately When rotating the button, the action should be rotated slowly, and the action should not be opened and closed suddenly, otherwise the knob is easy to be damaged.

1.How to light a gas stove.

2.First, adjust the knob on the valve and unscrew it counterclockwise. Before using, we must smell if there is any unpleasant smell. Then stop for a moment if there is no sound of air leakage, and so everything is very. Click again after normal.

3.Press and hold the switch on the gas stove and you won't let go, then rotate it to the left. A "pop" sound will be heard, so the fire will be ignited. It worked. If there is no sound, then press and hold the switch again and rotate to the left until the ignition is successful.

The ignition pin of a gas stove is a small metal probe wrapped in white ceramic with a metal cylinder shape of about 2 mm at the top, which is usually located next to the control panel of the gas stove and is used to ignite the burner of the gas stove. When using a gas stove, the ignition needle is a vital component, so it needs to be effective and clean at all times to ensure the proper use of the gas stove.

<> Extended Information - What is the role of the ignition needle in a gas stove?

The gas stove lighter needle is an electrical component used to ignite the gas stove, its function is to press the gas switch, generate a high-voltage arc or spark, and ignite it when the gas or natural gas is mixed with air, so as to realize the use of the gas stove.

Hello dear! There are many models of ignition needles for gas stoves; The gas stove has more than two needles to make Jane, one needle ignition needle, and more than one induction needle. Stoves have more than two needles, one ignition needle and more than one induction needle.

Then the differences between the two needles are as follows. Function: The ignition needle is mainly used for discharging.

A pulsed high-voltage current is conducted to the tip of the ignition needle. The induction needle is mainly used to sense the temperature of the stove (whether it is burning or not): the ignition needle is cylindrical wrapped in white ceramic, and the top metal is also cylindrical.

There are two types of induction needles, ion induction needles and thermocouple induction needles, both of which are pointed at the top. The ion sensing needle body is also a white ceramic cylinder. The thermocouple induction needle is brass-colored as a whole.

Both the ignition needle and the induction needle are used to transmit current signals. The ignition needle has a current of up to 1000+ volts and a slide beam. Guo Zi's induction needle mainly converts temperature information into micro-electric currents of different intensities and sends back pulses.

The thermocouple induction needle generates a current according to the temperature to keep the solenoid valve open.

The igniter is a pulse high-frequency oscillator composed of electronic components, and the high-frequency voltage generated by the oscillator is raised to a high voltage of 15kV through a step-up transformer, and the tip is discharged, and the gas on the burner is ignited by the discharged spark.

This kind of igniter has a high ignition rate, can be continuously discharged, press the knob, and the pulse igniter starts to ignite; Release the knob and the pulse stops ignition.

The gas stove is mainly located in the gap between the stove and the upper cover to supplement the lack of air during combustion, so as to promote combustion and reduce the generation of carbon monoxide and nitrogen oxides.

Nowadays, there are two main ways to light gas cookers:

One is a pulse igniter: it is a pulse high-frequency oscillator composed of electronic components (see Figure 2-5). The high-frequency voltage generated by the oscillator is raised to a high voltage of 15kV by the step-up transformer, and the tip is discharged, and the gas on the burner is ignited by the spark of the discharge.

This igniter has a high ignition rate and can be discharged continuously. Press the knob and the pulse igniter starts ignition; Release the knob and the pulse stops ignition.

The other is the piezoelectric ceramic igniter: it mainly relies on the ceramic element with piezoelectric effect to convert mechanical energy into electrical energy, instantaneous discharge, and discharge spark ignition gas. It is composed of a high-voltage ignition needle, a high-voltage rubber wire, a piezoelectric ceramic, a hammer, a return spring, and a housing body (see Figure 4-02).

Piezoelectric ceramics mainly include ceramic materials with lead cobalt titanate as raw materials, which are made of cylindrical ceramics by a series of processes such as molding, sintering, electrode and polarization. The arrangement of positive and negative ions on this ceramic lattice is non-centrally symmetrical, so that a potential difference (voltage) is created between the two ends of the ceramic under the action of external forces. The voltage generated is directly proportional to the external force and the height of the piezoelectric ceramic, and inversely proportional to the cross-section of the ceramic.

The igniter is to connect two positive electrodes of pressed ceramics with the same geometric shape, lead out with high-pressure resistant rubber multi-strand copper core wires, and after the negative electrodes are matched with two copper end faces, they are sealed with polycarbonate plastic, which is convenient for multiple impacts of piezoelectric ceramics. When the knob is pressed and rotated, the knob rod drives the fork on the gas valve core to swing, pushing the hammer in the igniter to move, the hammer return spring is compressed, when the knob rotates to 90°, the fork is detached from the hammer, under the action of the spring force, the hammer hits the negative pole of the piezoelectric ceramic, and at the other end (positive pole) produces an instantaneous high voltage (15kv), and the ignition is ignited for ground discharge.

Turn on the main gas switch first, and then turn on the stove switch, and the gas stove should not be lit with matches.

Household gas stoves have electronic ignition devices; When the switch is turned on, the electronic ignition device discharges the battery at high frequency to produce an electric spark that ignites the liquefied gas.

Turn on the main gas switch first, then turn on the stove switch, and light it with a match.

Turn on the switch first, turn on the small point. Light the fire again. It's dangerous to turn on too big a flame.

Gas stove ignition method: you need to open the hidden and blue gas source of the gas stove first, and then press the ignition knob of the gas stove, and rotate 90 degrees in the counterclockwise direction.

Household gas stoves are gas appliances that are used to cook dishes and process food through the conversion of chemical energy from gas to heat energy to meet the needs of the family. The gas stove consists of a gas supply part, a combustion part and an auxiliary part. In November 2021, the State Administration for Market Regulation issued consumption tips for 7 types of products, including household gas stoves.

According to the use of gas stoves, the gas source can be divided into liquefied petroleum gas stoves, natural gas stoves and artificial gas stoves; According to the material of the cooktop, it can be divided into stainless steel stove, enamel stove, paint stove and tempered glass stove, etc.; According to the number of burners, it can be divided into monocular foci, binocular foci, three-eye foci and multi-eye foci; According to the position of the burner to introduce primary air, it can be divided into upper air inlet stove and lower air inlet stove; According to the combustion mode, it can be divided into atmospheric gas stove and fully premixed gas stove; According to the installation method, it can be divided into built-in stove and desktop stove.

Precautions for the use of gas stoves

1. First of all, you must be clear about the gas source used in your home. Clarify the gas source, after installation, please read the product manual carefully before using the gas cooker.

2. Be sure to buy a gas stove with an automatic flame-out protection device.

3. In the use of the stove, if you find that the fire is off, turn off the switch immediately. Open doors and windows for ventilation, and when there is no smell of gas, find out the cause of extinguishing the fire, and properly dispose of it before re-igniting.

4. Before stopping the use of gas or going to bed, check whether the gas appliance switches are all turned off.

5. If the hose connection method is used between the gas stove and the pipeline, it is necessary to check whether the hose is damaged and aged and whether there is air leakage. The method is to apply soap, and the air leakage point is the place where the bubbles are blown continuously.

6. It is strictly forbidden to install gas meters and stoves in the bedroom, nor can they sleep in the kitchen equipped with gas facilities. In addition, do not pile up sundries and flammable and explosive materials near the gas stove to prevent fire and accidents.

7. After the gas cooker is used, it should be maintained regularly, and the fire cover should be cleaned frequently to prevent dirt from blocking the fire hole and causing the stove to backfire.

The igniter is a pulse high-frequency oscillator composed of electronic components, and the high-frequency voltage generated by the oscillator is raised to a high voltage of 15kV through a step-up transformer, and the tip is discharged, and the gas on the burner is ignited by the spark of discharge.

This kind of igniter has a high ignition rate, can be continuously discharged, press the knob, and the pulse igniter starts to ignite and start the nucleus; Release the knob and the pulse stops ignition.

The gas stove is mainly located in the gap between the stove and the upper cover to supplement the lack of air during combustion, so as to promote combustion and reduce the generation of carbon monoxide and nitrogen oxides.