-
Pry with a screwdriver.
Take your time. You're going to install the side axles.
Be careful when prying.
Don't do it on the lone wolf pattern anymore.
Because it hurts like that.
So you pry in the silver place.
I can't help it if I can't pry it open.
-
In fact, suction cups are the safest way, but you don't need to, so you have to use a screwdriver. It's going to hurt.
-
I'm helpless, unless I use the dishwash.
The more risky thing is to pry it open with a screwdriver or pliers.
-
You'd better buy a suction cup for only 2 yuan, so that you can install the side bearings without breaking!!
Right!!
-
Use a lighter to burn the lid, poke it with a pair of scissors when it is soft, and pry it up.
-
If the lid is chiseled, the outside of the lid of Snow Scale Peak is sealed with a metal ring and cannot be opened with a suction cup.
-
Landlord, it is best to use a suction cup that does not destroy the lid, but also can be installed and is not expensive.
-
Suction cup **Net 4 yuan a, lz can be bought. Wish.
-
Knives, chisels, tapers, etc. are destroyed.
-
The fastest one is to take a scissor tip and pry it open with a pry of the lid.
-
Put it in the refrigerator and freeze it for 2-3 minutes, then suck it off with a suction cup to remove it.
-
Use a suction cup, I'm a player of Snowscale, and that's how I got it.
-
Take it and burn it, and then take the scissors and pull it out.
-
No, you can turn it counterclockwise and you can turn it away.
-
How much is it, if it's a miscellaneous kind that can't be opened. If you don't have the money, it's better to buy the kind that costs a dozen dollars.
-
Just hold the halves and twist them gently.
He'll turn on. There are screws in it.
-
Yes, you will regret that the dry spring cave is the first song to lower the lid and go up again. I don't know if you want to, the way is to use a knife. Your lid falls off. It's just that I can't go up anymore.
-
Any knife will work (except nail clippers), just plunge it into it and another one.
-
With that screwed thing, I hammered it into the lid with a hammer and it came out as soon as I pulled it out, and that's how my Snow Scale V took it.
-
You can unload, you don't understand, it will be better after the lone wolf is unloaded. I used something very sharp to hammer in and pry it out, but I couldn't install the side axles.
-
You think it's Thunder S? A lone wolf can't be unloaded.
-
If you can't unload it, it's not good to unload it.
-
You should have removed the lone wolf's shell so you can see the holes inside! Then buy a side axle, remember it's the third generation, don't buy the firepower in a daze, I'll be guilty (cry)! To destroy the shell of a lone wolf, you have to be prepared, if you remove it, you can't install it, or it has been destroyed!
-
It's best to use a suction cup with a little more suction power that can be pulled off. Don't pry with something, it's easy to break the edge. Some people say it's hot water, but I haven't used it.
-
How to take the cap: Suck it out with a suction cup, or light a stick of incense, poke a hole in the ball cover with the burning end, and then insert scissors into the hole and pry it open.
Pick me!
-
Go buy a big suction cup and it will come down as soon as you suck it. Or the method of hurting the ball, use a compass to make a hole and then warp it open.
-
To put it simply: first the bearing, then the rubber ring, and finally the plastic cap. Oh.
-
Go to the official website of Audi to inquire** or go to the yo-yo store to ask, there is one in Wenzhou, in the sports center. You can check the Audi branch in your area. But I don't know if I can find it.
-
You first ask the lone wolf if it can be installed, and then if you don't use a suction cup, use a screwdriver to smash a hole in the lid and pry it up.
-
The ice spirit is good, and the photon elf can dance, but it is difficult to turn the rope.
-
You first see if there is a place to install side axles, if there are any, buy 2 side axles and let people install them for you, it is nothing more than spending more money.
-
The ice spirit is good, and the photon elf is very shaking.
-
It's not a clear plastic lid with a silver piece of paper with a wolf painted on it.
-
Stupid! You wouldn't try it with a magnet or a metal detector.
-
How much did you buy it? 70 yuan is the real card.
It doesn't have to be a metal ball that is heavier, just like the Ice Spirit, which is lighter than Snow Scale Peak. Snow Scale Peak is generally good, I bought one, and the timer is two and a half minutes. However, there is an iron ring on the outside, so it will be a little heavier. >>>More
In contrast, the light is a little more useful. It has a good upper line width, slightly lighter than ice, and is just right for the move. The ice is slightly heavier, so it takes a bit more effort to do the movement. >>>More
It's not dead, yours is a bearing type, you just hypnotize it hard, this is a common thing. >>>More
Dear、I think it's super light.、But it still depends on what you think.。
To give you a word, difficult. The process of making the bearings is much the same, but few of the various shafts in my hands are silent. The original Tianhuan's bearing is silent, and the silence is very good, but there are very few. >>>More