The motor is running from a distance, what is the reason for the end of the operation?

Tripping is nothing more than overload current caused, the general control power supply is from the power supply to take a phase, it is recommended to check whether there is a short circuit in the control loop, and at the same time control the power switch whether there is a defect that refuses to move needs to be replaced.

If the motor shows movement from a distance, then it is very likely that there is a problem with some of the sensors or drivers in it.

If the motor runs remotely, there should be no current accessed, so it will lead to this.

The motor is running from afar, but it is not running on the spot, that is, it is tripped, and the motor may be burned

If that runs, he must have a reason, because the system is not good.

If this happens, there should be a problem between the display and the control system inside.

There's no way to run it, which means that there is no current plugged in, so you can reconnect the current.

The motor is displayed in the distance and is running. Well, not running in place. What is the reason? Well, that's still your electric car? Isn't it time to discriminate against you when it's running, right?

Maybe it's because there's something wrong with his display that he can't do that.

The day is different, many say that it is really useless to put it for a long time, and it will be checked at the front desk.

When the remote display of the motor is running, it will no longer run on the spot, at this time, because in our display process, there is no way to remotely control the remote control panel and control equipment.

The motor is far away to show what is the reason for the operation of the position, this must be whether there is any fault in the machine, please ask a professional to come and repair it for you.

What situation do you want to ask? Even if you don't allow it, why can't you get through? What is the reason why the principle of doomsday can be done?

The motor is far away to show the operation and locate the reason for the operation, which means that he can't run without electricity.

In this case, it may be that your signal cable is connected incorrectly, just check the signal cable of the remote transmission of the motor.

How far away is the display run, what is the reason for that run?

If it shows starting, there should be a problem with the motor in this unstarted one, and you can plug it back in.

Finally, if the electronic clock and the distant city are activated, there is no possibility of activation, the main reason is because the voltage is not enough.

The start display in the far side of the motor is not starting. That is, not doing a boot correctly.

There should be a kind of boot failure, or identify the problem, it is best to find someone to help detect it.

Jingdong Display can't come up with different laymen, the reason is the same.

The original direction of the motor is started, and the reason why it is not started locally is caused by failure.

Is the far position of the transfer switch connected to the trip circuit, what kind of comprehensive insurance is used? Is it that the parameters in the comprehensive insurance are set improperly.

You said it was not detailed, is it a start-up and stop circuit??

Far away and in place? As the name suggests, the distance is not in the vicinity of control, or the tremor is next door, or it is rotten and you can't touch the year nearby, or you can't see it, and the place is in front of you, casually or in the range of stepping.

The so-called remote control refers to the control of the machine after the establishment of the data link, in fact, it is no different from the local control, and finally the local machine is controlled, its signal is the control command digital, but only the local machine is controlled, and then the local machine sends out a current or simulated signal to finally control the machine.

Because there are generally several locations where the opening and closing command is executed in the entire opening and closing control loop of the circuit breaker, there are several levels of control locations that can be switched in remote places. From the control power supply, there are centralized control stations, controlled stations, automation equipment (automation I 0 is locked by five preventions, and substations that have not been transformed by automation are remote control of the control screen), operation boxes, local switch cabinets (trolley type) and opening and closing switches or buttons in the mechanism box. The closer you are to the opening and closing coils, the higher their switching priority.

When switching to "in-place", it means that the toggle switch with a lower priority than you is ineffective, and the corresponding control location loses its opening and closing effect. Since normal operation must go through the five-proof locking, the switch switch with a higher priority than the RTU equipment in the above control location must be placed in the "remote" position when running.

Another function of the in-place remote transfer switch in the circuit breaker mechanism box is to place it in the "in-place" position when the circuit breaker is overhauled, as an obvious safety measure. Prevent personal injury to circuit breaker maintenance personnel caused by accidental circuit breaker operation. Since the switch switch in the circuit breaker mechanism box is "in place", which not only invalidates the lower priority control point, but also trips the locking protection, the switch is never allowed to be in the "in place" position during operation.

The so-called remote control refers to the control of the machine after the data link is established, but only the local machine is controlled, and then the local machine sends out a current or simulated signal to finally control the machine.

It is estimated that the circuit with position feedback in the field is interrupted, so that the regulator cannot give instructions to the electric actuator.

The wire is not connected, you check the remote line from the inverter to the PLC (controller). The most important thing is that there may be a problem with the controller's wire.