Where are the water meters generally installed in the community?

The water meter of the community is generally installed in **? 1. If the water meter of a rural single-family house is usually installed on the first floor, there is no unified form of installation location, which depends on the installation habits of each household.

2. The water meter of the old residential building is also installed on the first floor, and the water meter of a building will be installed in the same place to facilitate meter reading; Some will be installed in every home, perhaps in the toilet or kitchen.

3. Now the design of the new building water supply, the water meter will generally be placed in the pipe room of the corridor, and there will be no water meter at home. There are also communities that will set up pipe wells, and generally the communities with pipe wells will install water meters in pipe wells.

The water meter of the community is usually installed in the pump room of the community. It is managed by the property management company. The community is supplied by the general meter of the Beijing Water Supply Group, that is, the overall water cost of the whole community is measured by the general meter of the community, calculated according to the unified water price standard of the whole city formulated by the city, and is charged by the water supply group.

However, in the case of individual households, the water bills are now paid directly by the users to the water company. Not related to the property. The property is only responsible for repairs.

Generally speaking, the water meter of the community is installed in the well room, because every community, every building, and every unit has a separate well and electric well room, which is also to make it more convenient for the management of the community.

We are in the corridor, you can ask about the property in the community. Generally, the water meter is a property management, and they need to open or agree to view it.

We are all in the place where the water pipe enters the house, and there is a drainage meter, and seven or eight families are together, which is convenient for people to read the meter.

Now the water meters in the building are installed in the corridor, so that it can also be seen at any time, and the meter reader is also convenient to record, which is convenient for everyone.

The community generally has a small room on each floor to put a water meter, look carefully, or ask the property.

Generally, the new residential areas are in the pipe shafts for heating and water supply, and the older residential areas without pipe shafts are all in the location of the water pipes entering the households.

Water meters are divided into analog, digital, and analog-digital combinations according to their forms. The reading methods of different water meters are similar, and the specific method is to open the meter cover and record it according to the number or pointer.

Selection of water meter:

1. Select the water meter specification.

Because the stability and durability of the water meter under the common flow rate are the best, it is more in line with the design requirements. If there is a margin for the water pipe considering the future water flow capacity, the water meter can be selected one level lower in the diameter specification.

2. Select the water meter indication type.

Generally, it is in the form of a word wheel, which is clear and easy to read. However, some people think that when it is not possible to read the meter at close range, it is better to install the pointer type, because this type can judge the reading according to the geometric angle of the pointer pointing, and there is no need to see the value on the scale cylinder grid.

The previous one said very well, should be at the beginning of the water pipe of each household, if the specific place is the current community type of households, then generally near the stairs of the unit building, there is a water meter box, which is installed in the unit of each household water meter, if it is an old-fashioned house (such as the unit of the house, etc.), then generally in the kitchen or bathroom main water pipe to the entrance of your home water pipe.

Lavatory... Some are not in the toilet, whether they are in the toilet or not, there is a water meter for every household under the well cover in front of the unit building.

New house words. Generally at the door.

Regarding the adjustment of the installation of one household and one meter of tap water in our city.

Approval of the charging standard.

City Water Company:

Your company's "Instructions on Adjusting the Quota Charge Standard for Water Connection Installation Projects" has been received.

With the approval of our bureau, your company has been trying to implement the charging standard for one household and one meter for residents' newly modified tap water for more than a year. For more than a year, your company has implemented the installation of one household and one meter in strict accordance with the voluntary principle and in strict accordance with the prescribed charging standards, and has achieved good social benefits.

Promote the development of the city's tap water installation business, in order to further standardize the city's residents water supply installation charge management, according to the provincial price bureau.

Provincial Department of Construction Gan Price Fee Zi 2001 No. 107 "Notice on Strengthening the Management of Urban Water Supply in the Province" and the Provincial Department of Construction issued by the Municipal Engineering Budget Quota Regulations and the Municipal Water Supply Company Installation Center to provide the project water connection cost, after research, the adjustment and tap water installation fee standard for one household and one meter is approved as follows:

1. Collective installation of one meter per household (more than 2 households) or one meter renovation project for one household (i.e., large meters divided into small meters): each household per meter (water meter diameter 15mm, water pipe diameter 25mm) charges 700 yuan (including household materials).

2. Separate new installation: the charging standard is 840 yuan (water meter diameter 15mm, water pipe diameter 25mm, pipe length 6m) If the user needs, the water pipe will be charged 10 yuan for each additional meter of water supply materials.

3. The above two charges include pipe costs, accessories costs, engineering costs, shift fees, water meters, water tanks, survey and design, and earthwork excavation.

All fees such as backfilling and table flushing shall not be charged.

Fourth, outside the general meter, if it is necessary to renovate the main pipe or change the water connection point, the actual material cost shall be calculated according to the provincial and municipal project quotas.

The above-mentioned fee standard will be implemented from January 1, 2005, and please go to the Municipal Price Bureau to go through the procedures for changing the "Fee Permit" after receiving the document.

This is the case. December 30, 2004.

Sure, if a stranger asks for help, it will be counted as money, and the relatives will say otherwise.

1. The caliber of the water meter should be determined according to the caliber of the installed pipeline, and the installation location should avoid exposure, flooding, freezing and pollution, so as to facilitate disassembly and swiping.

2. The water meter should be installed horizontally (display facing up).

3. Before the new installation, the sand, gravel, hemp and other debris in the pipeline should be removed to avoid water meter failure.

4. The direction of the arrow shown in the water meter should be consistent with the direction of the water flow of the pipeline.

5. If the water meter is installed at the water inlet end of the boiler, it is best to install a check valve at the outlet of the water meter to prevent the boiler hot water and steam from backing up and damaging the internal parts of the water meter.

1. Before installing the water meter on the newly laid pipeline, the debris in the pipeline must be washed clean before installation, because a large part of the reason why the water meter slows down or stops is that the hemp wire, the iron tumor on the inner wall of the pipeline, and the sediment that precipitates the water meter stop, so that the water meter measurement is more accurate and reliable.

2. The water meter should be installed so that the direction on the surface of the meter is consistent with the flow direction of the water in the pipeline. The location of the water meter device should be as easy as possible to read and change the meter, and prevent direct invasion of the sun and cold wind. The water meter dial should be upwards and should not be tilted.

If the inclination will increase the friction resistance between the wheel shafts of the water meter, and even cause the water meter gear to mesh properly, so that the sensitivity of the water meter will be reduced, and the water meter will go slower and slower with the increase of the tilt angle.

Third, now the implementation of the practice of installing meters out of the house, because the outdoor working environment is much worse than indoors, the ordinary water meter group concentrated in the outdoor has been exposed to the sun and rain for a long time, and the gear in the water meter has been in a high temperature state for a long time, which is easy to deform and age, which greatly affects the measurement accuracy of the water meter. Even if it is used for a long time under normal working conditions, the dial on which the water meter pointer is aligned can easily generate dirt, obscuring the scale and making it impossible for the meter reader to read accurately. Therefore, outdoor installation of water meters should generally be installed with a protective box.

Fourth, some water meters do not meet the requirements, the reason is that some are limited by the installation space conditions, and some are due to the lack of technical knowledge of the installer, such as the installation of water meters immediately after the valve, and the water meters that should be installed horizontally are installed vertically, in order to make the reading convenient, the degree disc that should be facing up to the side and other wrong operations.

Basic installation requirements for water meters:

1. In order to ensure the most accurate measurement, install a straight pipe section with the same cross-section as the pipeline at least 5 times the meter diameter before the water meter inlet, and install a straight pipe section with at least 2 times the meter diameter at the water meter outlet;

2. The connecting pipes upstream and downstream of the water meter cannot be reduced;

3. It is recommended to install flow control equipment (such as valves) and filtration equipment;

4. The flange sealing ring shall not protrude into the pipeline or be misplaced;

5. Before installing the water meter, the pipeline must be thoroughly cleaned to avoid damage to the water meter by debris;

6. The direction of water flow in the water meter should be consistent with the direction of water flow in the pipeline;

7. After the water meter is installed, the water should be slowly discharged to fill the pipeline to prevent the high-speed air flow from damaging the water meter;

8. The installation position should ensure that the pipeline is filled with water, and the bubbles will not be concentrated in the meter, and the water meter should be avoided from being installed at the highest point of the pipeline;

9. The water meter should be protected from water pressure impact;

10. The small-caliber rotor water meter must be installed horizontally. Tilting backwards and forwards or side-to-side can result in reduced sensitivity.

Answer: Before installing a water meter, it is necessary to purchase a water meter with the appropriate caliber and specifications. According to the caliber of the installation pipeline, the location of the installation water meter can not withstand sun exposure, freezing, pollution and flooding, and it should be convenient for disassembly and maintenance. When installing, the display surface of the water meter should be facing upwards and maintaining a horizontal position.

This allows the installation to accurately measure the amount of water and to read the data easily. If it is a newly installed water pipe, then all kinds of debris in the pipe must be cleaned first, otherwise it will cause damage to the internal structure of the water meter, so that the water meter will fail or be damaged. There is an arrow on the surface of the meter, and the direction shown by the arrow should be consistent with the direction of the water flow in the pipe.

If the water meter is installed at the inlet end of the boiler, it is necessary to do a good job of preventing the backflow of boiler steam, otherwise it will cause serious damage to the internal parts of the water meter. The best way to do this is to install a check valve at the water meter outlet.

There are arrows on the side of the water meter, the side of the arrow is connected to the water end of your home, and the side of the tail of the arrow is connected to the household end.

The inlet and outlet of the water meter are not in a straight line, the low one is the water inlet, and the high end is the water outlet.

Which side is the water inlet?

With the improvement of living conditions, many people choose to buy a house. However, some people are worried that the water meter should be installed in **? Is it indoors or outdoors? Are there any precautions? Let's take a look.

1. The water meter is generally installed in the first place.

For the sake of aesthetics and space-saving, water meters are generally installed in their own kitchens, and some of them will be installed in the corner of the kitchen, or covered with other kitchen furniture. But in order to make it easier to see the readings of the water meter, it is best to install the water meter in a conspicuous location. If the house is a special type, then it may be necessary to install it outdoors.

2. Precautions for water meter installation.

1. If the water meter is installed on the new pipeline, it is necessary to rinse all the stolen goods in the pipeline first, so as to avoid the problem of the water meter slowing down or not going in the later stage.

2. It is best to install a filter before going to the water meter if the conditions permit, and the debris in the pipeline should be removed before the installation of other instruments in the pipeline to avoid pipeline blockage.

3. When installing, the direction on the case should be consistent with the direction of water flow, and the place where the water meter is installed should be located in the best place to facilitate our later reading or changing the mountain for later years. The place where the water meter is installed should not be installed in an exposed and frozen place as much as possible.

4. When the water meter is installed, it should show that the reading side is facing up.

5. The direction of the arrow on the water meter should be the same as the direction of the water flow in the pipeline.

6. If the water meter is installed outdoors, it must be protected from the sun and freeze. Because the outdoor environment is not as good as the indoor environment, if the water meter is exposed to the sun or cold for a long time, it will affect the service life of the water meter. If the gear of the water meter is exposed to the sun for a long time, it will cause deformation and damage, which will affect the accuracy of the water meter measurement.

Summary: The above is the content of how to install the water meter on ** and the precautions for the installation of the water meter. As a common tool in family life, it is necessary to understand the installation and precautions of some water meters to avoid problems.

Where are water meters generally installed? Generally, the water meter is installed underneath the kitchen sink, but some people install the water meter elsewhere in the kitchen. Of course, some people also install their meters outdoors.

No matter where it is installed, it is best not to be blocked by other things, otherwise it will be difficult to read the water meter.

Precautions for installation of household water meters1. If people install water meters on newly laid water pipes, all the debris in the pipeline should be flushed and cleaned, and if there are foreign objects, the water meter will not turn or turn very slowly.

2. When the ruler water meter is installed, the direction of the square on the case and the flow direction of the water in the pipeline should be in the same direction.