There is hot water on the side of the mixed faucet, and there is hot water on both sides of the fauc

The red is hot water and the blue is cold water.

As shown in the figure, almost all the faucets in the hotel are double-channel, with one channel for hot water and one channel for cold water. Before turning on the water, carefully observe the joints of the two channels and the walls of the pipes. Location as shown in the image:

You'll notice a few small differences between the two. There are dots or marks on the seam on one side, which are limescale. As we all know, limescale is the residue left at the bottom of the pot when boiling water.

Then the faucet in the bathroom will also have scale, and the occasional leakage of the water pipe joints for a long time will form scale at the joints. Therefore, it can be concluded that the side with limescale is hot water. This is shown in the figure below.

Even if the faucet is of good quality and does not leak, then when taking a bath, the water droplets in the air will fall on the faucet, and after the water droplets evaporate, it will also form scale.

If the hotel's faucet is newly replaced, limescale has not yet formed. Then there is only one way, first turn the faucet to one side, boil the water for about 30 seconds, if it is still cold water, then the other side is hot water.

The standard is hot water on the left and cold water on the right, in fact, some plumbers install the hot and cold water pipes upside down, or the installer reverses the inlet hose of the faucet when connecting the angle valve.

If the plumber installs it correctly, it should be hot on the left and cold on the right.

1. There is a problem with the water heater.

The hot water power from the water heater is generated by the pressure of cold water, and the hot water pressure will be less than that of cold water in the process of turning into hot water through the water heater, such as its own density, circulation resistance, etc., and the hot water pipe and the cold water pipe are connected with a short wire high-pressure hose with equal pressure, and the hot water will be held in the water heater because of the pressure difference, so the hot water cannot be released.

In this case, it is necessary to check whether the valve on the water heater inlet pipeline is fully open, and replace or remove the pressure relief valve and possible filters on the tap water inlet pipeline of the water heater. Open the plug of the drain valve at the bottom of the water heater to drain the water heater, and let go of the tap water to flush the dirt on the inner wall of the water heater multiple times.

2. The hot water pipe is connected incorrectly.

The connection of the water connection pipe of the hot and cold water faucet needs to be careful. If the hot water outlet of the faucet is connected to the cold water pipe, there will also be a phenomenon that the faucet does not produce hot water. In this case, you need to check all the connections of the faucet's inlet water pipe to ensure that there are no wrong connections.

Summary. 1: There is hot water on both sides of the faucet, and the hot and cold mixing valve is broken.

1: There is hot water on both sides of the faucet, and the hot and cold mixing valve is broken.

The mixing valve is faulty, and the hot water is mixed into the cold water pipeline 2. The pressure of the hot water pipeline is too large, resulting in the mixing of cold and hot flow, and generally this situation should be impurities in the pipe, which is blocked in the pipe elbow of your bathroom heating, and there is no other way to solve the problem except to disassemble it.

You remove the hot water hose of the faucet and try the water directly, which is normally a problem with the faucet.

Because the water from the hot water tap comes out of bai very much.

du small causes the flow of water to be too small

You can't put the fire of the water heater on the dao, you turn the heat back to the faucet in other places and the kitchen at the same time, and there will be hot water The problem is mainly in the water heater Its water flow switch sensitivity is not high enough There is also to ensure that the water pressure and pipeline are smooth I am a water purifier with 10 years of experience You can ask me qq 524166656

The water heater outlet valve is checked to see if it has been moved.

There is also a filter screen at the water inlet of the water heater, take it apart and take a look

There is a problem with your faucet, it is advisable to replace it.

You bought some groceries.

Alas. Why didn't you listen to my advice in the first place?

But I'll say it again.

Gorin bathroom. , stainless steel faucets. Look at the picture.

In order to facilitate home life, many people will choose to install a faucet with hot and cold water pipes in their homes, so that they can have hot water flowing out at all times to ensure a normal home life. So whether the left side of the faucet is hot water or the right side of the faucet, and how to maintain the faucet, do you understand? Now let's take a look.

1. Is there hot water on the left or right side of the faucet?

To the left of the faucet is hot water. In the process of installing the cold and hot water pipes of the faucet, in order to facilitate the later use and maintenance, the hot water pipe will be installed on the left side of the cold water pipe. However, some family faucets will install the hot water pipe on the right side, so it must be noted clearly to avoid affecting the normal use.

Second, how to maintain the faucet.

1. When using the faucet daily, it is necessary to develop a good habit and not use too much force, otherwise it is easy to loosen the sealing valve of the faucet, which will affect the daily use, not to mention, there may be water leakage, and maintenance will become more troublesome. Therefore, when turning the faucet on and off, it should be gentle.

2. The faucet nozzle used for bathing should also pay special attention to daily maintenance. In the process of use, let it be in a stretched state, and when not in use, it is necessary to coil the hose on the faucet, and ensure that there will be no dead angles, to prevent the hose of the sprinkler head from being damaged, resulting in the later period can not be used normally.

3. Usually, you also need to pay attention to the cleaning of the faucet, every time you use the faucet, you need to use a dry cloth to wipe it clean, and then return to the good filial piety after the water is dry to form scale on its surface, and then if you want to clean, it will become very troublesome. Moreover, the steel wool ball should not be used to disassemble the faucet to prevent damage to the surface paint.

Regarding whether the left side of the faucet is hot water or the right side is hot water, and how to maintain the water leakage faucet, I will introduce it here, do you understand? The left side of the faucet is hot water, if there are special circumstances to change, then it will be communicated with the owner in advance, so as not to affect the normal use.

Summary. 1. Once you find that the electric water heater is leaking, immediately unplug the power cord and turn off the water inlet switch; 2. Most of the reasons for the leakage of the electric water heater are the sealing problems of the joint between the heating pipe and the inner tank, and it can be seen from the later repairs that the sealing ring between the flange of the heating pipe base and the inner tank is broken, and the sealing ring must be replaced to solve the leakage problem. I hope it can help you and wish you a happy life

The water heater faucet to which side is to put water Hello dear, the water inlet and outlet of the hot and cold water dragon collapse head are divided into left and right, the left side is the water outlet draft, the left side of the water heater is the hot water outlet, and the right side is the cold water inlet. I hope it can help you and wish you a happy life

How to turn off the water leakage on the side of the water boiler.

How to turn off the water leakage on the side of the water boilerHello dear, 1. Once you find that the electric water heater is leaking, immediately unplug the power cord and turn off the water switch into Tongzhi; 2. Most of the reasons for the leakage of the electric water heater are the sealing problems of the joint between the heating pipe and the inner tank, and it can be seen from the later repairs that the sealing ring between the flange of the heating pipe base and the inner tank of the local Fengmin is broken, and the sealing ring must be replaced to solve the problem of water leakage. I hope I can help you, and I wish you a happy life