Why is the water temperature of the electric hot water faucet low and the flow rate small?

The flow is large, the relative power is also relatively large, and the power of at least 8000 watts is required to open and heat the shape, so the power of 8000 watts is not good for the wires of the general family, which is easy to produce potential safety hazards.

The electric hot water faucet (also known as the hot water faucet or the fast hot water faucet) comprises the faucet body and the water flow control switch, the faucet body is provided with a heating chamber and an electrical control cavity, separated by a sealing plate, the electrical control cavity is provided with a heating circuit, the heating chamber is provided with a heating pipe, the heating pipe power is generally in 2-3kw, and the hot water can be heated in 3-5 seconds, and the heating pipe is connected to the heating circuit, and it is characterized in that the heating pipe is an insulated heating pipe; The insulated heating pipe is a water and electricity isolated insulated heating pipe; Most of the faucet body is a high-temperature resistant engineering plastic type, and a few are all-metal type; There is an insulated water pressure switch in the electrical control chamber. The heating circuit is equipped with an electrical switch, which is connected with the end of the insulated water pressure switch, which can turn on and off the water and electricity, and is equipped with a temperature controller and an anti-dry burning device, and can also be equipped with a leakage protection switch.

The flow is large, the relative power is also relatively large, I have asked many manufacturers, said that the instant hot shape needs at least 8000 watts of power, then 8000 watts of power is not good for the general family wire, at most 4 square lines, easy to produce potential safety hazards,

Carefully analyze the market and invest cautiously.

A small amount of hot water from the faucet can be a problem with clogging or water pressure.

1. Let's check first, whether the water output of this one faucet is small, or whether all faucets have small water output. If only one faucet has a small amount of water, it can be determined that the faucet is clogged. There is a filter at the bottom of the faucet, or there is an aerator, which is most likely to clog, resulting in a relatively small flow of water.

2. If the water output of all the faucets is relatively small, it is a problem of water pressure, especially for some high-rise households, when they encounter the peak period of water consumption, there will be insufficient water pressure, so the water output of each faucet at home will be very small.

Cleaning tips for faucets

1. The faucet is prone to limescale after being used for a long time, you can use baking soda, white vinegar, and water to make your own detergent, and pour them into the spraying can. Wrap the faucet in a paper towel, stir the homemade detergent well and spray it on the surface of the faucet. In about half an hour or so, we remove the paper towel from the faucet and rinse it off with a wash.

2. When we clean the faucet, don't forget to clean the faucet filter, we can soak the faucet filter in white vinegar water for cleaning. If there are impurities such as sand in the faucet, you can only remove the filter and clean it. When cleaning the faucet, do not use acidic and alkaline detergents to clean and so on.

If the angle valve or valve is not fully opened, you need to turn off the valve and unscrew the faucet to check if there are any impurities clogged, and also check whether the valve is open to the maximum. If the water pressure is unstable, a booster pump can be installed. It is also possible that the nozzle is clogged and the hose needs to be removed and inspected for deterioration.

If the angle valve or valve is not fully opened, you need to turn off the valve and unscrew the faucet to check if there are any impurities clogged, and also check whether the valve is open to the maximum. If the water pressure is unstable, a booster pump can be installed. It is also possible that the nozzle is clogged and the hose needs to be removed and inspected for deterioration.

This pipe and commodity problem and water pressure problem, according to your statement, depending on the water pressure problem has been ruled out, then the remaining two reasons are the first two reasons, 1 is that there may be a blockage of the pipe leading to the kitchen, 2 the cold water angle valve or the mixing valve of the sink has a problem with the cold water diameter or blockage. You can first swap the water inlet pipe and angle valve of the mixing valve (on the outlet of the angle valve or on the faucet water inlet), if the cold water becomes larger and the hot water is smaller, it is the problem between the angle valve and the mixing valve, if it is exactly the same after the change, the water pressure and flow rate from the wall are small.

If there is really any reason, that is, the volume of hot water becomes larger, the pressure becomes larger, but it is often not caused by this problem in daily life, if it does not affect the use of it, do not care, if it is affected, turn on the cold water faucet, see if the raw material belt is blocked, or the water saving head of the cold water outlet is a bit of a bet.

Hello, it is a pleasure to serve you and give you the following answers: Reasons:1

There is air and water vapor in the hot water pipeline, and when the reed fiber faucet is turned on, the air and water vapor will be squeezed out, reducing the temperature of the water. 2.There is limescale in the hot water pipeline, and when the scale accumulates too much, it will affect the flow rate of the water, thereby reducing the temperature of the water.

Workaround:1Wash the water pipes of the electric faucet to remove air and moisture.

2.Wash the pipes with hot water to remove limescale. Steps:

1.First, turn off the faucet of the electric hot water faucet and disconnect the power. 2.

Then, use a screwdriver to gently unscrew the screws of the faucet and remove the lid from the pipe. 3.Wash the water pipes with warm water to remove air and moisture.

4.Rinse the limescale inside the hose with warm water. 5.

Wipe the water inside the faucet's hose with a clean rag and gently screw the screws back to place the lid back in place. 6.Finally, reconnect the power of the electric water faucet and turn on the faucet to solve the problem of water temperature dropping.

Related knowledge: The electric hot water faucet is a new type of faucet formed by combining an electric heating device with an ordinary faucet, which can heat the water before it flows out, and the user can get hot water immediately after unscrewing the faucet.

The faucet has hot water and cold water, and the water output is large after boiling hot water, and the water output is very small after turning on cold water, what is going on?

Dear, hello, this pipeline and commodity problem and water pressure problem, according to your statement, depending on the water pressure problem has been ruled out, then the remaining is the first two lead frank reasons, that is, there may be a blockage of the pipe road leading to the kitchen, and the cold water angle valve or the mixing valve of the sink has a problem with the cold water diameter or blockage. You can first swap the water inlet pipe and angle valve of the mixing valve (on the outlet of the angle valve or on the faucet water inlet), if the cold water becomes larger and the hot water is smaller, it is the problem between the angle valve and the mixing valve.