If you find that there are not enough sockets after decoration, can you only install a socket?

Normally, we choose the socket panel, the vast majority of which are five-hole, two or three plugs in one, and a socket is only plugged in one electrical appliance for a few calls, and the other cannot be plugged in, resulting in a waste of resources and insufficient sockets. Cheap drag strips are of poor quality and prone to failure. If you feel that the height is not good-looking, and you don't want to settle, then only reduce the height, and add a few more sockets, it is not too difficult, and you can hire an electrician if you can't do it yourself, this kind of work is a piece of cake for the decoration electrician to do.

Changing the concealed socket to a sliding socket can basically cover the original position, but the requirements for your original wire are relatively high.

<> if you have a mess of wiring in your home, you can route them along the edges of the baseboard or door frame, or install the wiring in the gap between the baseboard and the wall. In addition, if the plastic integrated material is used, it has a buckle, and the circuit can be placed in the baseboard. You can try to use an extension socket, which is a socket that is plugged into a socket, and one socket can be expanded into two or three sockets.

The existing socket can be changed to a triple row of multi-hole sockets, effectively increasing the number of sockets. If the location of the socket is not suitable, you can draw a neutral wire from the socket in another location and install the socket.

Concealed installation is necessary to reserve the bottom nest of Ha, it is not recommended to reserve, find a plumber to plan, individuals generally for the control of several roads, single control and double control, socket power these may not be considered, once reserved and then change time-consuming and laboriousThis mainly depends on the layout requirements of the line pipe, the installation requirements of the switch socket, and the aesthetic requirements of the circuit transformation. The function of the bottom box is twofold: 1. Fix the panel, where to fix the bottom box panel, how to fix it 2, and prevent leakage.

So for the sake of safety, it is better to install the bottom box. You must install the back box, otherwise you won't be able to install the switch panel and socket panel later! After moving into the new house, I found that the bathroom junction box did not press the bottom box, and I bought the bottom box artifact from the Internet, but there was a toilet in the way, and then the operation was troublesome, and I couldn't get it.

Later, it was simply punched in the tile and tightened with an expansion wire.

Yes, because the sockets are reserved in the wall, and when the overall decoration is installed, there will be no wiring for you to install the socket, and at this time, the socket is not enough, so you can only use the socket.

Of course. If there are not many sockets, you can only use the socket strip to make up for this regret.

Yes, so in the actual use process, you must consider the need for sockets, try to measure the distance and height, and don't let the home be full of sockets.

Yes, it is more difficult to route the line after decoration, so everyone must do a good job in advance when decorating.

The cost of renovation will increase, and the style of the house will be ruined.

When decorating, what are the consequences if there are too many outlets?

If you have a lot of sockets in your home, it will lead to a significant increase in the cost of renovation, such as the cost of switch panels, the cost of telecommunications and cassette, and the cost of installers. If there are too many sockets, then the style of the house will also be ruined.

If you don't plan it properly, the location of the socket will be messy, and it will be everywhere on the ground and on the wall, and it may exist at different heights. This can ruin the decoration style and decoration effect of the house, and to put it bluntly, it is a bit like a coat with patches everywhere.

If there are too many plugs, there are also safety and hygiene risks

In terms of safety, if there are too many plug board wires, then it will increase the probability of natural things, especially in the bathroom or some humid places in the kitchen. In addition, after the plug is installed, the ground will protrude by a height, which is easy to trip over children or the elderly. In terms of hygiene, the plug-in panel is generally protruding, and the protruding part is easy to accumulate dust, so it is relatively troublesome and complicated to clean.

There are too many outlets, and to some extent, there are pros and cons

Although there are many disadvantages to too many operations, it is not a disadvantage, mainly depending on whether the socket arrangement is reasonable. However, in some places where the power consumption is relatively high, multiple sockets are arranged, so it will be more convenient in the production process after that, and it will also facilitate our lives.

Therefore, when you design the room, you must reasonably arrange the position of the socket, and you must also reasonably plan the role of the socket. In this way, you can experience great relaxation during the check-in process, and you will not be troubled by too many sockets. In the process of renovating your home, how many outlets will you choose to install?

What is the layout of your installation? Welcome to exchange and discuss.

Many people move in after the house is renovated, only to find that there are some places where there are no sockets installed, which brings a lot of inconvenience to life. If the house is being renovated or not being renovated, it is advisable to do a good job of water and electricity works. It is an invisible decoration, invisible and impossible to preserve.

Many plumbers will also advise property owners to keep more outlets when doing hydropower. Maybe they can't use them now, but science and technology are developing and may one day be used. They can try to keep as many outlets as possible in their home, which is better than installing too few outlets.

The living room and dining room need to cooperate with the design plan the most. The light lines for the ceiling were kept and given to the designer.

As a reminder, when lying on the couch playing with your phone and playing without power, you will know how necessary it is to leave power on the couch. When your beloved girl grabs the power, you'll find that it's okay to leave one more. When you can't find a place to plug it in, you'll understand why you're reminded to leave the power supply on your desk.

The water dispenser will be placed in ** and the power supply should remain in the corresponding position.

In the necessary corridors of the home, a power supply 20 cm above the ground should be reserved. This power supply is best used with your daughter-in-law. Whether you buy a robot vacuum cleaner or not, there will always be someone who needs to sweep the floor.

When your daughter-in-law takes the vacuum cleaner and pinchs her waist and asks you for power, you'll know how good my reminder is. It's also a good thing to plug in a small floor lamp when you don't have a power source, because the little one wants to raise fish after waking up at night, and you happen to have another fish tank, so you need to know that the fish need oxygen. If you don't plan to come alone in the future, then it's also worth leaving a potential opportunity in advance!

Air conditioners should consider whether to use a crane or cabinet unit. The difference is that the hanging machine is hung on the wall, while the cabinet machine stands on the ground. The key is to maintain the potential according to their location!

In short, it's how big your living room is and how you plan to fill it. If electricity is needed, it should be prepared in advance. One or two people can be booked on standby.

It may cause the line to be too disordered and complex, affect the normal use of the line, lead to serious poor contact, and too many sockets for decoration will also affect the overall decoration aesthetics of the room, so that the wall does not look well divided, affecting the normal use.

It will affect the overall aesthetics, and may also lead to a waste of resources, and sometimes unreasonable distribution will affect the use of furniture, which may expose a lot of threads. Leakage is possible.

It may lead to poor decoration effect, may cause the house to look more cumbersome, may cause the house to look messy, will lead to electricity leakage, and may lead to fire.

It will be more convenient to use, of course, it may also affect the appearance, not so beautiful.

We can arrange a few more sockets, and we can expand that kind of socket, so that it can be convenient for our life, which is a very good situation.

The only remedy for the sockets that have been renovated is not enough for the house:

1. The wall is slotted and buried to remedy, but it is impossible, and the wall is damaged.

2. Row all the way to the open line.

3. Add drag line board (socket row). There is no other way.

Before the decoration, if the number of sockets is not installed in advance, it needs to be reinstalled after the decoration, so how to repair the sockets after the decoration? Let's learn together.

1. How to repair the socket after decoration.

1. Concealed installation: first chisel out the socket line on the wall, then bury the wire, then repair the wall, and finally connect the socket and the line together and fix it on the wall.

2. Surface installation: first pull a wire from the power box to the wall, then fix the wire on the wall, then connect the socket and the wire together, and fix the socket on the wall.

3. Socket strip: Buy a socket strip with multiple interfaces, then insert the plug of the socket strip into the peripheral socket, and then pull the socket strip to the position where the socket needs to be used and put it away. The length of the socket can be selected according to the needs of use.

Second, what aspects need to be paid attention to when installing the socket.

1. When installing, it is recommended that you do not install the socket on the waist line of the tile, if the user chooses to install the socket on the waist line of the tile, it will cause the tile waist line to be cut off, causing unnecessary damage, because the tile with the waist line is generally more expensive, and after the waist line is cut, the overall decorative effect will decline.

2. When installing, the socket can not be installed at the interface position of the two tiles, otherwise it is easy to cause the tile to crack in the later stage, it is recommended that the tile is installed in the small and medium-sized position of the tile, so as to effectively avoid tile cracking, hollowing, etc.

The above is a detailed introduction to how to repair the socket and install the socket after decoration, I hope it can help friends in need.

I can only connect a few more power strips. Since the socket is no longer enough, and the house has been renovated, it can only be solved by this method.

I think the best thing to do is to re-groove and install a few more outlets, so that will solve the problem.

If you don't want to slot to add a socket, then connect the openwire box socket at the original socket.

You can go outside and find a casual worker, the kind that does water and electricity, and wiring it at the nearest place where you want to power up the board, the project is very small! And it doesn't cost a lot of money!

Replaced the original socket with a little more socket.

The most thorough way is to use brute force.

One side is the plug, the other side is the socket, the wiring comes out into the electrical appliances, the first plug and the plug matching, end to end, infinite expansion, more electrical appliances, one socket is enough!

Mantong plug surface and socket surface are equipped with special matching card slots, and the connection is firm and no longer depends on the socket metal sheet clamping, and will not easily fall off.

The functional metal sheet of the Mantong socket is a U-shaped structure, and the metal sheet of the plug is in contact with two planes, which is several times better than the contact effect of the traditional plug and socket just two wires, and the metal contact surface is large and conductive, and the heat is small.

The metal piece of the plug and socket is no longer responsible for clamping the plug function, and there is no need for much clamping force; The socket hole is a small long hole of the national standard, and there is not much movable space; The card slot can be positioned so that the plug cannot move on the socket; These tricks are universal enough to be universal in a lifetime without shrapnel slackening resulting in poor contact, for other people's socket shrapnel slack, Mantong also has the ultimate solution: the plug metal plug is adjustable, and the plug plug can be applied to all kinds of loosely plugged sockets, which is a unique trick of brute innovation.

There's a more amazing feature in Mantong! When you install the wiring, remove the metal piece of the plug, which is a separate socket.

The fairly versatile jack is the smallest of all the socket jacks, and the three-pole jack face is recessed for higher security.

Well, you don't need to buy plugs and sockets in the future, it's enough to have a rough pass.

The first way: find an electrician, and the electrician will help you solve all professional problems. The second way:

If you want to pay attention to aesthetics, re-chisel the wall and install the socket in the place where the air conditioner is to be installed, and then repair the squeegee. This is a dark line. The third way:

Buy a special socket for air conditioning, from other sockets or power sources along the corner of the debater's wall wiring groove or conduit, pull the copper wire file to lead over, that is, install the open wire.

Those who have experience in renovation know that before arranging the location of the electrical outlets, the size of the furniture to be placed should be provided to the plumber as accurately as possible.

On the premise of not affecting the appearance, if the location cannot be accurately determined, then reserve as many power outlets as possible to use sooner or later in the future. For the regret that the socket in the decorated house is too small, the decoration designer suggests that if you find that the socket is not enough after moving in, you should buy a few more sockets, for the tidiness of the room, the sockets should be placed behind large items such as cabinets, sofas or TVs as much as possible. You can buy a plug board with a plug of 10 amps and a socket of 16 amps and 2500 watts.

Before buying, look at whether the three-pin plug of your air conditioner is ordinary or thickened. Then choose the hollow shape of the above plug plate according to the size of the plug. Now I have to use a socket row, and the connection of the socket row is not less than the square.

Or from the nearest socket, start slotting, downtubing, threading, and installing air conditioning sockets on the wall, and then putty to do a net leveling and scraping, and restore the original state. If you feel that the socket can't be brought up, it is recommended to find an electrician to help you solve the problem.