-
The headphones are plugged into the front two holes to hear but not speak,].
Make sure your front panel is plugged in and not broken.
If you plug it in the back, you can say that you can't listen to it. It used to be normal. ]
Since the latter can say that the driver is normal, it is very likely that your audio output port has been broken.
It is recommended that you change the sound card or try the latest version of the driver to have a look!
-
Right-click the volume icon in the lower right corner -- Properties -- Advanced -- Options -- and check "phone" in it.
-
Control the voice --- the faceplate. Audio Devices There are two options out there for Sound and Audio Devices. Sound Manager: You tune it in.
Earsets won't be a problem, right? Hope you can fix it.
-
The earphones can be heard but not spoken when plugged into the front two holes, and can be said but not heard when plugged in the back"Being able to listen and speak at the same time, there's nothing wrong with the software, the problem is with the audio input port in front of you and the output port in the back.
-
You install the sound card driver again, although the system may have recognized the sound card driver by itself, but some functions cannot be used because it is not the driver that comes with the driver disk itself. I've had your problem before, and that's how I solved it.
-
First of all, the computer is silent and seems simple, but in fact, sometimes the problem is more complicated, involving both hardware and software problems. Therefore, it is necessary to find out the cause first, see if the software or hardware is malfunctioning, and then prescribe the right medicine for the problem. We must not mess around for unknown reasons, because if we don't do it, the system will be paralyzed, and the trouble will be big.
1. Check whether the sound card, connection cable, and speaker and other embedded equipment are connected normally; Run anti-virus software for anti-virus;
2. Right-click "My Computer" -- Properties -- Hardware -- Device Manager, and open "Sound, ** and Game Controller" to see if there is any yellow in front of you? "If so, reinstall the driver for this device to solve the problem;
4. When there is no sound and no speaker, open the control panel--- Add and remove programs--- add and delete Windows components, put a check mark in front of "Accessories and Tools", click "Next", and then, shut down and restart, the system will prompt you to install new hardware, follow the prompts to install;
5. Uninstall the sound card driver, reinstall or upgrade the audio driver;
6. When the sound card driver is installed, the prompt "AC chip cannot be found" appears, it may be computer poisoning, or the sound card driver has been deleted by mistake due to illegal operation, or there is an internal software conflict. The solution is to reinstall the system and drivers.
7. Simply ignore it, wait for a period of time after shutting down and then turn it back on, sometimes the sound problem will solve itself. You might as well give it a try.
-
Use the driver wizard and other similar software to solve the problem!
Search engines make it easy for users to find information, you only need to type in a few keywords, and any information you want will be gathered in front of your computer from all corners of the world. However, if you don't do it properly, the search efficiency will be greatly reduced. >>>More
You're a rookie! The process you open yourself can be turned off except for the antivirus and the input method.。 You can optimize it with Super Bunny or something. >>>More
If you do the design, you don't need to change the graphics card.,But it's sure to be 1G memory.,I'm studying architecture.,512's memory is really.。 >>>More
The graphics card is obviously too poor. For motherboards, consider using MSI P43-C51, which supports DDR3. >>>More
1. VT is a one-way thyristor, when the effective trigger voltage is added between the cathode K and the gate G (the trigger voltage of different types of thyristors is not necessarily the same), VT will be triggered and turned on, after VT is turned on, as long as the working voltage between the anode A and the cathode K of VT remains unchanged, even if the trigger voltage disappears, VT will still maintain the conduction state. >>>More