Handmade by primary school students and the easiest steps

Elementary school students make small crafts as follows:

Tools Raw materials: shells, cardboard, black beads such as longan cores or black clasps, colored pencils, glue, thread.

1. Eat shells tonight, just enough to use, the shells are all split into halves, dried after completion, and set aside for square cardboard.

<>2. Square cardboard 45 degrees, sharp corners upward, make the head part of the peacock. First, the head and neck of the peacock are placed on the surface of the shell, and the beak can be made with a half-broken shell, and then glued one by one with glue.

3. Then use the inner part of the shell to swing out its tail, as much as possible to curvature. Once you have made a shape you are satisfied with, you can start gluing them one by one.

4. Find a bead such as a longan core or a black buckle and stick it on the eye part, there happens to be one such branch at home, and it is just right to paste it and use it as a crown.

5. Use colored pens to color the shells of the tail.

6. Find some threads to dig a hole above the cardboard, pass through to make a hangable one, and make a lot of threads at the bottom, which becomes the shape of a Chinese knot.

Homemade flashlight.

The specific method of making it is to remove one end of the lid of a waste can (such as a Lulu beverage can) and knock the other end with a round hammer. Roll up two No. 1 batteries with thick corrugated cardboard and put them into the tank with the positive electrode facing up and the negative electrode facing down.

Find a suitable plastic lid (such as a magic big roll lid that can be fastened to Lulu cans) and dig a small circular hole in the lid** in such a size that the bulb is plugged in tightly. Insert the base of the bulb into the small hole. Take a piece of wire hunt and peel off the wire skin at both ends, wrap one end around the lamp base, and pierce a small hole through the side of the plastic cover with the other end.

Place the plastic lid over the can. Check that the bulb and battery are in close contact. At this point, the disposable flashlight is ready.

When using, use your thumb to press the wire threaded from the side wall on the weld that is not painted from the can, the flashlight will glow, and the thumb will jump off the wire, and the flashlight will go out, which is very convenient to use.

1.Simple wind turbine physics plus art plus production: a can, a pair of scissors, a tinplate, a wooden strip, a four-wheel drive motor, a bottle of super glue, some colored LED bulbs (or bulbs, diodes).

A: Use scissors to cut off the upper part of the can by about 1cm, keep the remaining can, that is, make a "cup" first, and then draw three at equal intervals on the cup, then keep these three, cut off the remaining excess, and then present a round base with three blades, like a propeller, and then use the tip of scissors to drill a round hole slightly smaller than the central axis of the motor in the middle of the base.

B: Tinplate (i.e., ordinary pieces of iron) wraps the motor firmly and then nails it to the wooden strips.

C: Fix the blade on the central axis of the motor with super glue to ensure the vertical, horizontal and windward nature of the blade.

D: Connect the two wires of the motor to the LED bulb to ensure that the wire interface is connected normally (positive and negative, good contact).

E: Running forward quickly with a wooden strip in hand, or installed on a bicycle, pushing the rotation of the blades under the action of the wind, and then pushing the rotation of the motor rotor, so the magnetic generation of electricity, the LED bulb will be on, if the wind is sustainable and stable, then there is no difference with a battery, if the wind is big and small, the LED bulb is on and off, if you add a sensitive charger, then you can store the current, and then release the current, it will be ideal.

How to make paper by hand for elementary school students:

1.Break the paper into a paste with water.

2.Add white dye to the "pulp".

3.Make a wire rectangle and put it on top with an old ** to make it look like a "strainer".

4.Put the wire rack into the pulp and pick it up slowly.

5.Dry the wire rack and you're done!

The easiest: put the waste paper in the beverage bottle and soak it and shake it evenly, then pour it on a denser cloth, spread it evenly, dehydrate it and press it tightly to dry. Soak the material in water, mash it into pulp, mix evenly, pour it evenly on the net, and dry it Handmade papermaking steps:

1. Add water to break the waste paper into a paste

2. Add white dye to the "pulp";

3. Make a wire rectangle and put it on top with the old ** to make it look like a "filter";

4. Put the wire frame into the pulp and pick it up slowly;

5. Dry the wire rack and you're done!

The paper used for firecrackers, paper umbrellas, and paper fans in the paper also has a unique style. For example, the firecrackers made of handmade coarse paper in Hunan Province not only have a crisp and bright sound, but also shredded paper into uniform small pieces after being ignited and exploded, and the image of falling is beautiful, the range is large, and it is relatively safe in transportation and storage.

The sacrificial paper produced by hand mainly includes yellow table paper, shroud paper, sacrificial paper, etc., which are mainly used for religious activities. The yellow table paper produced in China has the special effect of curling when ignited and burning, and large pieces of paper ash falling, which is exactly what religious activities require.

Although handmade paper is not used to print books, journals and other publications (except manuscripts), in order to have a more comprehensive understanding of paper and papermaking, it is necessary to have a general understanding of the production methods and main varieties of handmade paper mentioned above. The easiest: put the waste paper in the beverage bottle and soak it and shake it evenly, then pour it on a denser cloth, spread it evenly, dehydrate it and press it tightly to dry.

Provide a greeting card as a practice, an original colored paper green piece. Yellow one. Glue, brush cut a symmetrical apple, fold it in half, use the remaining paper to cut a 5 mm wide yellow strip of paper, fold the two strips of paper from the middle to 90 degrees, and then cross fold, that is, the paper spring, not too long, as the body of the caterpillar, sticking to the outside of the apple.

Draw the caterpillar's head yourself. In the greeting card, you can draw something at will. Use the strainer to fish in the pulp a few more times, the paper will be thicker, and I have been very obsessed with the Rubik's Cube recently, but I am still at the level of a primary school student, and I only know the third order, and the speed needs to be improved urgently, and I haven't advanced a minute and a half.

If you use words to form a sentence, you must first understand the meaning of the words.

When using related words, you must first understand what relationship the related words represent.

Transitions, connections, progressions, cause and effect...

Ambiguity should be prevented. You first do the handicraft [experience it yourself].

After doing it, write your own feelings and get what inspiration [in a book; Abbreviately].

Later, recall what you wrote and write it on your composition [preferably after you have done the handiwork].

When writing an essay, just write about your actions, demeanor, mental activity, and language.

Paper flowers (can be **weather).

Materials: Pink paper, straws, concentrated salt water, glue.

How to make It Fold pink paper into paper flowers, dip them in concentrated salt water, and then glue the flowers to the straw.

Description The color will be lighter, and the weather will be clearer; The color becomes darker, and the weather will turn cloudy or rainy.