Can the place where the sewing agent fell off be repaired?

Yes, clean up the surroundings After there is no dust, you can use Dubaxter sewing agent to hit it, it is very strong, it will not collapse and will not fall off.

It can be patched, but it will still fall if it is only held for a while.

Hope it helps you, hope.

Yes, it is recommended to shovel off the side before repairing.

You can use the hot air of a hair dryer to blow on the sewing agent (shovel off the excess or unpretty) on both sides, soften it, and then wipe it off little by little with a sponge or rag. Note: In this case, it is not recommended to use a shovel to remove, and uneven tiles are easy to scratch the tiles when shoveling.

Then re-construct and cover a new one to go up!

Yes, with Van Tony all-ceramic glue.

How to choose tiles.

1. Look at the surface of the tile.

If the gloss of the tile surface is higher, the better the sintering density of the tile. Good tiles, the glaze presents a crystal clear feeling, under the illumination of the light, like a mirror can reflect the light, poor tiles, the glaze is dull.

2. Listen to the sound to distinguish the good from the bad.

Gently tap the surface of the tile with your hand to listen to the sound, the sound of good tile density is relatively crisp and bright, and the sound of poor tile density is relatively dull.

3. Weigh the weight of the tile.

Weigh the weight of the tile, the good tile has a high density, the weight is heavier, more solid, and the weight of the poor quality tile is relatively light.

How to remove the rework of the sewing agent: The rework method of the sewing glue needs to be simplified: 1. The sewing agent is not cured:

Just hit the sewing agent, the sewing agent has not been cured, found that the construction is not perfect, need to be redone, directly with the sewing knife to clean up, the gap in the sewing agent cleaned up, and then re-glue the seam can be completed, if you find that there is a bad place, you must rework before the curing of the poor hidden pants, do not wait until the curing to find that the construction effect is poor and then rework. 2. The sewing agent has been solidified: the sewing agent has been solidified, and the inspection found that the sewing has not been done well, so it is more troublesome to clean up and rework at this time, and it needs to be cleaned with professional equipment.

First of all, it is necessary to prepare two very important tools: one is a high-power heat gun, and the other is a shovel. The sewing agent has been cured and tightly bonded to the gap, and it is necessary to blow the sewing agent soft with a heat gun so that it can be shoveled out with a shovel.

Then use a heat gun and a shovel blade to blow and shovel and slowly clean it up.

Beautiful seam is a kind of decoration of tile gaps, and beautiful seam requires a lot of patience and care. Otherwise, you won't be able to achieve a good-looking effect! For novices in beauty sewing, it is inevitable that beauty will fail.

So, can beauty sewing be a second remedy? How to get rid of the sewing agent and redo it? Here we will bring you the second remedy for beauty sewing.

Can beauty sewing be a second remedy?

If the sewing is not done well for the first time, it can be redone for the second time. It's just that rework and redo are more cumbersome and waste a lot of materials. And it depends on the situation, if the sewing agent has not dried, it is easier to shovel or repair. If it has been cured, it is more troublesome.

How to get rid of the sewing agent and redo it?

1. If the type of sewing agent is different, the method of eradication will be different. Among them, the one-component beauty joint agent is water-based, and the adhesion is generally not strong, so it will be easier to shovel off, as long as the tile gap position is scraped continuously with a utility knife, it can generally be easily shoveled off.

2. In the process of sewing construction, it is found that there is no good sewing agent, use a sewing knife to deduct the undone sewing agent, re-glue, and then press the seam, in the construction process the sewing agent has not been cured, the sewing agent is still soft, it is easy to deduct the sewing agent with a sewing knife, if you wait for the sewing agent to be deducted in the curing process, it is more time-consuming.

3. The hardness of the two-component sewing agent will be higher, so it will be more difficult to clean. If it is a solidified sewing agent, then you only need to prepare professional rework tools, a 1600-watt heat gun, and a shovel. Use a heat gun to blow the sewing agent that needs to be reworked, blow the sewing agent with a hot air gun in one hand in the front, blow the sewing agent softly, hold a shovel in the other hand in the back, follow the heat gun and push the sewing agent forward, and the sewing agent after blowing soft is gently pushed out of the tile gap with a shovel.

4. Remember to clean up the gaps, especially the reworked tile gaps, to clean them cleanly, and there can be no residue of the joint agent in the gaps, including the edge of the tile gaps, otherwise particles will appear when pressing the joints, resulting in uneven and smooth surface of the joint. Don't look at the technical content of beauty sewing is not high, but doing beauty sewing is a meticulous work, you need to have enough patience, confidence and carefulness, focus in order to do a good job in beauty sewing, focus to be professional.

5. When cleaning the sewing agent, be sure to wait for the sewing agent to blow soft before shoveling, do not use a vigorous shovel, and do not blow the heat gun against a place for a long time, the tile gap will become brittle because of the heat gun baking for a long time, otherwise vigorously use the shovel to clean the sewing agent, the tile gap is easy to collapse porcelain, if it is for the customer's home to rework, the tile is damaged, not only can not pay the wages, but to compensate the owner for the loss, the novice is easy to make such a fatal mistake, so the gain outweighs the loss.

The above is about whether the beauty sewing can be remedied twice, how to get rid of the beauty sewing agent and then re-introduce the brother shed. If the beauty sewing fails, you don't need to be gray and patient, you can shovel it and redo it. It's about spending more time and materials. Therefore, when constructing beautiful sewing, we must master the skills, be focused and careful enough.

1. Repair on the original basis, you can directly repair on the original basis, and directly make up another layer. The applicable situation is that the beauty seam sinks with a large arc, the color matching is not good-looking, and the surface treatment is uneven.

2. Remove all the old beauty seams and redo them, some friends are worried that the first method will be used to remedy them, and the overall effect will be poor, so you can choose to eradicate and redo the beauty seams.

Operation method: If the sewing agent is not completely cured, directly use a utility knife or sewing cone to remove the problematic sewing glue and clean the gap. If the sewing agent has been cured, you can blow the sewing agent soft with a heat gun first, and then use a utility knife to remove and clean it.

Common causes of beauty seams falling off:

1. The beauty sewing is not dry, the beauty sewing agent is made of AB two-component mixture, if the AB two-component material is not mixed evenly, it is very likely to fall off in the future! Generally, novices are prone to make this mistake when operating, so you must remember to deglue first, that is, to discharge the first 30cm of the sewing glue.

2. The tile cross interface is not smooth, after the beauty of the seam glue is laid, the horizontal and vertical scraping should be carried out, and then from the inside to the outside of the tile handover of the intersection to ensure that the surface of the seam is smooth and tight.

3. The cleaning of tile gaps is not in place, and the beauty of the joint adhesive should be stable, and the cleaning of tile gaps must be in place. If there is dust or impurities in the gaps of the tiles, the follow-up joint adhesive will also easily fall off.

No, unless the product is not up to par or the construction master is not doing a good job, the dust in the gaps must be cleaned before construction and there can be no water, otherwise it will cause it to fall off easily in the later stage.

Improper maintenance or use will cause falling off, Chengdu Meritor sewing company, the construction warranty of the sewing agent is 18 months.

A good beauty sewing agent and a standardized construction method will generally not fall off.

First of all, the quality must be passable, and it is best to understand the use of the brand when buying; During construction, the most important thing is the treatment of the bottom, the beauty sewing agent can also be said to be an upgraded product or a substitute for the caulk, but it is necessary to carry out the bottom of the gap, it is best not to be deeper than two millimeters, not too shallow, the bottom can be treated with cement or special bottom material, and it needs to be treated flat.

No. The beauty joint agent is the beautification product of the tile gap, the beauty joint agent does not have the effect of beautification and the role of caulking, the beauty joint agent replaces the original traditional caulk and grout and white lime, the beauty joint agent is impermeable and waterproof and oil-proof, will not become dirty and black, will not fall off, and the beauty of the joint has many colors, which can be matched with the color of the tile to play a beautifying role.

What is the cause of the sewing agent falling off?

The first reason: improper treatment of tile gaps, local no coverage leads to the process of construction, first of all, we clean out part of the caulk in the construction process, in the construction process of the caulk, if the tile gap is not smooth, there is dust, there are water droplets, so it will lead to the combination of the caulk and the caulk is not firm and leads to falling off.

The second reason: caused by improper construction.

In the construction process, after dealing with the gaps, in the process of playing the beauty joint, the beauty joint agent does not cover the tile gaps completely, and water droplets will enter in daily use, in this case, there will also be peeling, falling off and other situations.

Normally, no, I recommend a few reliable big brands JCDecaux, Vicano, and Black & Decker.

There are still some differences between caulk and Lougu sewing agent, it is a new type of material, it is very rich and natural and delicate in gloss and color, caulk can bring better overall effect to the wall. Caulk is particularly sticky and shrinks in his vintage, has a strong grip in color, and is resistant to stress, abrasion and mold.

Definitely.

Don't look good-looking, walking back and forth for a long time will certainly fall off

Whether the sewing agent can be removed after a long time depends on what sewing agent you use, if it is a one-component one-component sewing agent, it is easy to remove, because its adhesion is not strong; The adhesion of real porcelain glue and self-leveling (Chunlan Dongyu) porcelain joint agent is firm after solidification, and it is more troublesome to remove!

I use Baxter two-component at home, very hard, very bright, if you say it is too difficult to remove and redo, but I have been doing it for two and a half years without any problems, but then again, it is easy to remove the redone sewing agent, the quality can be seen in general, indicating that the viscosity is too poor!