How to restore the factory settings of the time switch?

There are also two types of push-button time switches: those with batteries (the case has a battery compartment) and those without batteries.

Push-button time-controlled switch with battery compartment in the case: After the debugging is messy, you only need to remove the battery and wait for a while to restore it to the factory settings.

The shell does not have a battery compartment for the button type timing switch: after the debugging is messy, you only need to calibrate the current time of the switch correctly and delete the previously set timing.

1.Double-click the "Cancel Recovery" button to unlock the screen. Press the "Calibration" button to calibrate the hour, the "Calibration" button to calibrate the minute, and the "Calibration" button to calibrate the week.

2.Click the timer button to see how many sets of timers there are, and click the cancel restore button one by one.

Bluetooth time-controlled switch(With power-off memory function): It is similar to the key-type time-control switch without battery, proofreading time, and deleting the timing before deletion, but the specific operation mode is different.

1.Control the layout of the applet, click on the calibration (one-click calibration, no need to proofread the day, hour, and minute respectively).

2.Press and hold the timer under the timer setting, and the "Warning" will pop up whether to delete the timer, click OK, click Save and send.

To operate it, you first need to go to the operation interface. Different models, the operation method is inconsistent, but it is similar. I'll take the picture above as an example.

If an A appears on the left side of the screen, it means that the screen is locked and needs to be unlocked first. Method:"Cancel the "Restore" button and press it 4 times in a row, and you can see that A is gone and the screen is unlocked.

To set the time, first press the "Timer" button, and the screen will display "1on...."。Press "Calibration" and "Calibration" respectively"button to adjust to your desired boot time.

Then press the "Timer" button again and the screen will show "1off...."Press "Calibration" and "Calibration" respectively"button to adjust to your desired shutdown time. And so on, you can set 8 or 16 time periods.

The time controller can be set for a minimum of 8 time periods. ”1on..."Indicates the start time of the first setting segment, and "1off" indicates the stop time of the first setting segment.

The picture below looks like it's set up.

Proofreading time. With the screen unlocked, press'School hours"button to complete the system time proofreading, and proofread "minutes" and "weeks" in turn'.

Acceptance of installation results. With the selection of the "Manual Auto" button, it is possible to check whether the circuit is installed correctly, remember: switch to "Auto" mode after inspection. The current status is displayed at the bottom of the screen.

The wiring method is marked below the time control switch, the left is the incoming wire, the right is the outgoing line, do not connect it in reverse.

If you need to set the time by yourself, you only need to press and hold the "clock" button and don't let go, then press "week" to set the week, press "hour" to set the hour, and press "minute" to set the minute.

The time control switch adjusts the time as follows:1. Take the Delixi KG316T time-control switch as an example, first press the "Cancel Recovery Key" to unlock the screen.

2. Then press the "Calibration" button to calibrate the hour, then press the "Calibration" button to calibrate the minute, and then press the "Calibration Week" to calibrate the week.

3. Press the "Timing" button again to set the power on and off time.

4. Press the "Auto Manual" button to adjust to automatic, you can turn on and off the machine regularly, and after the setting is completed, press "Cancel Recovery".

Do the math how much it will cost you to renovate your home

Now the various industrial electrical appliances and household electrical appliances will use the time control switch, the time control switch is safe and saves money by the very power and money, so how to set the time control switch?

The function of the time-control switch.

The time control switch is a multi-period control switch that can be cycled in a day or a week, the time can be set from 1 second to 168 hours, 1-4 groups can be set every day, the output current can be 10-25A, and it can also control 2200W or higher power electrical appliances to work, it can be controlled in multiple ways, and it is effective for a long time when set.

How to set the time switch.

1.The first step is to unlock first, cancel the button and press the restore button 4 times in a row to unlock it. After unlocking, the time switch will automatically lock after 15 seconds without any operation.

2.The second step, proofread the time first, you can calibrate the time by a few buttons to calibrate the time, if you don't need to modify it, just press "set".

3.Continue to press "Timing" to set multiple switches: 2 on, 2 off, 3 on, 3 off, etc., and so on, and so on, if you don't need so many groups, you can press "Cancel Restore" to delete the unwanted ones.

4.After all the time settings are completed, we can press the "Auto Manual" key to switch, so that the setting is completed, if you want to cancel the time set before, you can press the "Timer" key, and then press "Restore Cancel" after deleting the desired time point.

Failure issues. 1. If the switch is not turned on or off at the specified time, it may be because the set time is not adjusted, and it should be set again.

2. If there is no error in setting the time of the switch, but it still can't be switched on and off normally, it may be that the excess time has not been eliminated.

3. If the above two are okay but the switch still can't be used, it may be that there is a problem with the "automatic manual" button, check the switch sign to adjust it to the state where the current time is, and then turn it back to the automatic position.

Article Summary: With the rapid improvement of science and technology, more and more new things have appeared around us. The time-controlled switch is a high-tech product, if you have such a switch at home, you can learn it, so that you can use the time-controlled switch more easily.

Enter the area and get the decoration for free**].

1. Take the Delixi KG316T time-control switch as an example, first press the "Cancel Recovery Key" to unlock the screen.

2. Then press the "Calibration" button to calibrate the hour, then press the "Calibration" button to calibrate the minute, and then press the "Calibration Week" to calibrate the week.

3. Press the "Timing" button again to set the power on and off time.

4. Press the "Auto Manual" button to adjust to automatic, you can turn on and off the machine regularly, and after the setting is completed, press "Cancel Recovery".

1. Press the "Clock" button once, then press the "Calibration" button, "Calibration" button and "Calibration" button respectively to adjust the clock to the current time, and then press the "Clock" button to confirm after setting, the LCD screen will display the current time. Turn left|Turn right to turn left|Turn right.

2.Press the "Timing" button, the word "i on" will appear at the bottom left of the LCD screen (indicating the first turning time), and then press the "Calibration Week" button, "Calibration Time" button and "Calibration" button, and enter the desired opening time. Turn left|Turn right to turn left|Turn right.

3.Press the "Timing" button again, the word "I off" will appear at the bottom left of the LCD screen (indicating the first closing time), and then press the "Calibration" button, "Calibration" button and "Calibration" button to enter the desired closing time. Turn left|Turn right to turn left|Turn right.

4.Continue to press the "Timer" button, and the bottom left of the display will be displayed in turn (2 on, 2off, 8 on, 8off).

Questions are only scheduled from Monday to Thursday.

Can't you set it on Friday and Saturday.

Questions: Closed Friday, Saturday, Saturday, and Sunday.

Required to be closed on Fridays, Saturdays and Sundays.

The push-button time-to-switch is set to a fixed week: one two.

Three, four, five. Six, one three.

Five, two, four, six, etc., cannot be arbitrarily chosen.

The Bluetooth time control switch can be set according to the needs of the click to select (random combination selection).

Ask the question, Delixi, press the key.

Press the "Timer" button and then the "Week" button to set which day of the week to turn on and off at the set time.

This way you can set Monday to Thursday open.

How to set the time control switch, the time control switch will not be used, there is a detailed tutorial here.

The setting of the time control switch is relatively simple, such as setting the opening time at 18:00 and the closing time at 05:00

The setting method is as follows, the first opening time is 18:00, the first level is set to 05:00, the second opening and two closing and the third opening and three closing all the way to ten opening and ten closing must clear the time to zero (because it is not used). Then set the day of the week, set the current time of the time switch, and turn the time switch to automatic.

You can refer to the manual to set it up, it's very simple. Just try a few more times.

The time-controlled switch panel has a calibration time press, first press the calibration time to press the health, and then see if the display flashes, if the minute zone flashes forward, you check the clock health, and then press the minute zone to proofread.

If you have time to proofread that thing, just adjust it first.