How to tie a rope, how to tie a rope

The 7 ways to tie the rope will be taught by hand and will be used one day.

1. First of all, make the rope into a figure-8 shape.

2. Then put the rope in the middle and press the rope.

3. Pull the long end over and place it on top of the short end.

4. Then pull the rope from below.

5. Put the rope back again.

5. Pull the rope on the outside through the rope on the inside and pull it from underneath.

6. Then just bring it up.

7. If the rope is put on it, it can be lifted.

The rope is tied in the following ways:

1. Single knot. This is the most familiar and primitive knotting method, which is generally used for knotting the end of the rope and some unimportant knots.

2. Eight characters through the knot (simply called the eight character knot). It is a commonly used knot in mountaineering and exploration activities, mainly used for the connection of the knot at the end of the rope and two ropes, and the insurance effect is stronger than that of a single knot and it is easy to untie.

3 Intertwined. It is used to connect two ropes of the same thickness, and is characterized by firmness, easy to solve, and beauty.

4. Single heavy knot. It is used to connect two ropes of different thicknesses.

5. Tight knots. It is used to connect two slippery ropes.

The method of tying the knot.

Knotting can be done either by hand or with the help of an instrument. Freehand knotting is more commonly used in surgery, which can be divided into two-handed knotting method and one-handed knotting method. Instrument knotting is knotted with the help of needle forceps or vascular forceps, also known as forceps knotting.

One-handed knotting method is simple and fast knotting method, easy to learn and understand, the most widely used in surgery, should focus on mastering and practicing, according to the operator's habits of different one-handed knotting method is divided into left-handed knotting method and right-hand knotting method.

Two-handed knotting method: It is more reliable than one-handed knotting, not easy to slip knots, and the method of two-handed knotting is more complex than that of one-handed knotting. In addition to general ligation, it is more reliable and convenient for deep or tissue tension suture ligation.

The two-handed knotting method can be divided into the two-handed knotting method with the same action and the two-hand knotting method with different movements.

Here are the various ways to tie the rope:

1. Double barta: This knot is very good, but it is not suitable for use in life, it is more suitable for use in handwork, decorated, simple and generous, beautiful and exquisite. Here's how:

First, wrap one side of the rope around it, and the part of the rope hanging down cannot be on the same side. Then put the two circles together. Use another rope to pass through, where the two loops coincide, and you're good to go.

2. Clover knot: This is also suitable for use in hand, so that the knot is small and cute, and the taste of the Chinese knot. Here's how:

First, wrap the rope around twice, and wrap it out twice, with a large circle and a small one, in the shape of an "8". Then pass one of the dangling ropes through the large circle from the front, and repeat the same action with the other through the small circle. Just take care of the rope after the left.

3. Slipknot: This settlement is relatively used and can be used on many occasions. Tie the rope in a knot first, but don't tie it tightly, leaving a loop.

Then turn one side of the rope around the other rope about three to five times, don't turn too tight, leave some gaps, and then it will be good to thread. After turning to the desired number of turns, pass the remaining rope through the previous turn and pull it tight.

4. Hanging leg knot: first fold the rope, and then wrap the rope head in the direction of the folded place, leave the loop reserved on it a little bigger, and wrap it from left to right in turn, and wrap the rope tightly when winding, so that the knot will be stronger; Finally, thread the end of the rope into the rope loop on the right and tighten the upper rope loop.

1. First of all, make the rope into a figure-8 shape.

2. Then put the rope in the middle and press the rope.

3. Pull the long end over and place it on top of the short end.

4. Then pull the rope from below.

5. Put the rope back again.

5. Pull the outer rope through the inner rope and pull it from under the mold code.

6. Then just bring it up.

7. If the rope is put on it, it can be lifted.

The earliest appearance of rope can be traced back tens of thousands of years. When humans began to have the simplest tools, they would use grass or small branches to twist and twist into ropes. People used it to tie wild beasts, tie thatched huts, make belts to tie straw skirts, ......Later, there was a "knotted rope note", in which knots of the size of the rope were used to record the antecedents of the bridge.

Summary. There are many ways to tie ropes, and the way to fix a single knot is to overlap the ends of two ropes with the ends and then tie a single knot. This knot is used to quickly connect two ropes of the same thickness, or to make a loop of rope, etc.

How to tie the rope.

There are many ways to tie ropes, and the way to fix a single knot is to overlap the ends of two ropes with the ends and then tie a single knot. This knot is used to quickly connect two ropes of the same thickness, or to make a loop of rope, etc.

Of all the knots, the backhand knot is the simplest. First, the rope is bent into a loop, and the loose end is pulled through the loop from behind. The overhand knot is rarely used for anything other than tying a knot at the end of the rope (so that the end of the rope does not fall apart), but it is an integral part of many other knots.

Method: First, bend the rope into a ring, put the ring on a fixed object, pull tightly, and then use the loose end to tie an overhand knot with the ring.

How to tie it up.

Don't you have a tiny black ribbon there, first pass one end through it, and then thread the colored ribbon through the middle of the black ribbon that you have passed through.

He has two holes, 2 rope heads, and the head is said to be black.

I know how to tie it here, put the little black wire through this hole first.

It turns out that there are two heads, and two holes need to be tied, one head is tied first, and then the other head is directly bound.