How to tie the rope of the jade pendant? How to tie a rope with a jade pendant

Step 1: Burn the heads of the two ropes with a lighter, twist the ropes before they solidify, and pass them through the holes in the jade.

Step 2: Separate the two ropes, flip the right rope over to it, and bend it to the left. Then the rope on the left presses down on the rope on the right.

Go around the back and go through the hole where the rope bends on the right. Pull the 2 ropes tight.

Step 3: Turn the left rope over to it, bend it to the right, pull the right rope, go around the back, thread through the hole in the left rope, and pull the 2 ropes tight.

Step 4: Repeat the second step by turning the right rope over and bending it to the left. Then the rope on the left presses down on the rope on the right.

Go around the back and go through the hole where the rope bends on the right. Pull the 2 ropes tight.

After this step, it's basically OK, if you don't think it's important, you can repeat the third step.

2) Jade matching Chinese have always had the habit of wearing jade, and the jade pei of the past generations was shaped like jade huang, jade long, jade, etc., and small round holes were drilled on it to facilitate the thread and tie these jade pendants to clothes. In addition, there is a complete set of jade pendants, which are composed of several different jade pendants to form a long string, and the method of connection is of course not by threading ropes and knots.

3) Apply the Printing Button and Mirror Button.

The ancients had the habit of wearing the seal supervision system on their bodies, compared with the Han seals that have been handed down, and the square has a seal button. The back of the ancient bronze mirror is cast with a mirror button, which can be tied to a rope for easy handholding. From these two places, it is not difficult to see that the application of knots in ancient Chinese life was quite extensive.

Here's how:Prepare tools: lanyard, scissors, lighter.

1. Roast the red rope over fire, and pinch it while it is hot, so that it can pass through the hole.

2. Fold the rope in half and pass the two rope ends through the middle part of the pendant hole together.

3. According to the size of the jade pendant, set aside a reasonable length for braiding the rope, which is usually more appropriate, depending on the personal preference to leave the appropriate length of the binding length such as 1cm.

4. Then pass the two ropes from the back through and make a simple cross joint.

5. Then go around to the other side to tie a knot, so that the knot is straight and the back is tied until the length of the rope head is left.

6. Then according to the thickness of the line, a reasonable part of the fixed line length is burned with fire, and the line on both sides is cut short with scissors as shown in the figure below.

7. Then use a lighter to gently bake the thread on both sides and solidify quickly, if the fire is too large, it may leave black spots.

8. Done. <>

Tools Raw materials: knotted rope, jade pendant, lighter draft Li machine.

1. Use a lighter to burn the head of the knotted rope, and quickly pinch and pull it with your hands to make the knotted rope slender. In this way, the knotted rope is easy to pass through the ornament to call the hole.

2. Note that when the knotted rope passes through the jewelry hole, the knotted rope needs to be in the back and the decoration needs to be in the front.

3. Then the first knot should be tied in the back, and the knot should be tied in the front to affect the beauty of the jade pendant, and then the knot should be tightened by hand.

4. Tie a knot to reverse, tie another knot, and so on and so on until the knot reaches the reserved length you like.

5. After tying the knot, deal with the head and let it, the usual practice is to burn the knot and hide it.

The knotting method of the jade pendant rope is as follows:

1. Use a lighter to burn the two ends of the rope slightly, and quickly pinch the tip with your fingers, being careful not to burn it.

2. Pass the two burnt heads through the jade pendant hanging hole at the same time.

3. As shown below, keep the length of 1cm at the lanyard.

4. Open the two red ropes that pass through the jade pendant, pull them forward, and wrap the position of the positive dust that has just been reserved for 1cm to tie a single knot.

5. Tie a knot on the reverse side and tighten it after Ran Hui clears the branch.

6. Then repeat the front and back knots.

7. Wrap all the reserved 1cm length until it is wrapped.

8. At the last knot, burn the red rope with a lighter, burn it, and fix the head.