If the toilet is installed in the bathroom, there is no need to store the inlet if it is a sewage pi

Install the toilet and drain it.

Pipes can be piped without the use of back-bends (or trap-and-traps).

If you do not use a reverse bend for the sewer pipe of the toilet, you need to combine the toilet and the sewer nozzle tightly and leave no gaps, so that there will be no odor. Toilet section.

As follows: <>

The internal structure of the toilet bowl itself has a reverse bend, which prevents the dirt below the high water level from volatilizing foul gases. If the connection between the toilet and the sewer pipe is not tightly combined, the dirty gas in the sewer pipe will leak out of the gap to the empty part of the toilet and then overflow through the gap between the toilet and the floor.

To do a good job of connecting the toilet drain and the sewer pipe, you can add a special rubber ring to achieve it. Its style is as follows:

Look at whether your toilet has a trap, but now ordinary toilets have traps, and there is no need to install a trap, but the floor drain in the bathroom should be paid attention to, and the odor-proof floor drain must be used to avoid being sad when you get it. The function of the water bay is to be more hygienic, to isolate the taste, and to effectively avoid the breeding of bacteria. Therefore, it is recommended that it be installed.

No, now there will be no aftertaste, if there is an aftertaste, it is a floor drain, and the floor drain can be anti-odor by pressing a floor drain treasure.

It is best to install a trap.

The trap is odour-resistant.

Some toilets are substituted for the sinking bay, some are not, and those with the sinking bay are not safe.

It is still necessary to install a sinking pipe, otherwise the bathroom will often smell.

If the sewer pipe is equipped with a trap, if it is blocked, there is no way to dredge it.

1.Step Category: Overall Introduction Required Tools Raw Materials Methods Steps Precautions.

2.General Knowledge: Direct questions give specific reasons in detail Reason introduction.

Of course, the toilet is placed in the bathroom, where do you mean shared sewer? The water trap should be installed, otherwise it will smell great.

The toilet is now filled with water storage underneath, so I'm worried about clogging.

The toilet itself has a waterproof bend, so there is no need to install any traps.

1. Negotiate with the owner downstairs to change the original pipeline directly from downstairs. This method is the least likely to cause clogging, provided that your landlord agrees, of course.

2. Raise the floor of the bathroom. The elevation of the floor is directly proportional to the drain in your toilet. If your room height is enough, you can choose this method, but this method may cause sewer blockage in the later stage, so you need to be cautious.

If you just want to make a toilet, you can choose a toilet shifter, but the farthest limit of the shifter is 15cm, which is more limited and more likely to be blocked.

3. Four common ways to renovate toilet drains teach you how to shift the toilet drain pipes.

1) Small-scale shift: use a special shifter for shifting, there is cm, it is recommended not to exceed 10cm shift, which will affect the effect of punching and draining.

2) Large-scale displacement: floor elevation (generally 20cm high), pipe discharge, pipeline should have a certain slope, but the distance should not be too long, the distance is long, the slope of the pipeline should be larger, the ground elevation will increase, and the flushing effect will also be affected. The drain pipe can be connected to the original pothole, or it can be connected to the sewer main with 3 passes.

3) Perforation and displacement of the floor slab: If it is a duplex or a villa, the floor slab can be punched and re-taken over.

4) Wall-row toilet: If possible, you can choose a wall-row toilet, as long as you build a short wall, the pipe is directly connected to the sewer main.

In decoration, waterproofing is often more important than any other topic. What should I pay attention to during the installation and use of pipes?

1. Be sure to find a professional technician to install the pipeline. No matter how luxurious and high-end your decoration is, it will not be worth it if you are not willing to spend money in this area. Often, the burst or leakage of the pipeline will cause the loss of the water pipe itself dozens of times, hundreds of times, or even thousands of times.

2. Be sure to carry out a pressurization test after installation. The pressurization test is generally carried out under the condition of double water pressure, and there should be no water leakage in the test.

3. Test method under no pressurized conditions:

1) Close the main valve of the water pipe. (i.e. the water pipe switch in front of the water meter).

2) Turn on the faucet in the room for 20 minutes, making sure there is no more water dripping and then turn off all the faucets.

3) Turn off the water inlet switch of toilet tanks and washing machines with water storage function.

3) Open the main valve of the water pipe.

4) Check whether the water meter is moving, including slow walking, 20 minutes after opening the main valve.

If there is movement, it is a water leak. If you don't move, you're fine.

4. In daily use, if the following situations are found, check the relevant pipelines as soon as possible

1) The surface of the wall paint is moldy and blistered.

2) Blackening of baseboards or wooden floors and fine bubbles on the surface.

The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implications?

Dear, hello, I am happy to serve you, the answer is as follows: The mouth of the toilet is flush with the ground, and the toilet can be installed. However, if you install it in this way and use the toilet later, there may be a sewage overflow.

It is not clear that when installing the toilet, it is necessary to play a circle of structural glue or glass glaze glue around the mouth of the sewer pipe, and the colloid height should not be less than one centimeter, and then place the toilet, so that when the toilet is used in the future, due to the barrier of the colloid, there will be no sewage overflow.

The mouth of the sewage pipe is flush with the floor, so can I install a toilet? What are the implications?

Kiss! Hello, happy to answer your <>

The sewer nozzle of the pro-toilet is flush with the ground, so it is possible to install the toilet. However, if you install it in this way, and use the toilet in the future, there may be a phenomenon of sewage overflowing. Therefore, when installing the toilet, it is necessary to put a circle of structural glue or glass glue around the mouth of the sewer pipe, and the height of the colloid should not be less than one centimeter, and then place the toilet, so that when the toilet is used in the future, due to the barrier of the colloid, there will be no sewage overflow.

What to do if the toilet drain and the floor are flat1Level the floor so that the lower drain pipe is slightly higher than the ground (you can first look at the height difference between the drain outlet of the new toilet and the lower edge). 2.

Place the toilet flange (a gummy circle) over the waterway pipe. 3.Press the toilet bowl against the flange from directly above.

4.Connect the water supply stub. When the toilet sewer pipe is installed, it can not be flush with the ground, if it is flush with the ground, the flange ring and sewer pipe of the toilet can not be well sealed, then when used in the future, there will be water leakage, aftertaste and other phenomena, I hope mine can help you <>

Do you have any other questions?

It cannot be installed.

Before installing a smart toilet, under normal circumstances, the decoration company reserves a sewage pipe 305mm or 400mm away from the wall. The diameter of the reserved sewage pipe hole is 100 (90mm-110mm), which is smaller or greater than this range and will cause the toilet to be unable to be installed.

The aperture is too small and needs to be reretrofitted. The aperture is too large, it can be modified directly on site, as shown in the figure below, the master inserts 1 to 2 circles of 100mm plastic pipe in the pipe diameter above 120mm, and fills in the sealing flange glue.

No, no, no. Because the toilet is connected to the septic tank through the sewage pipe, and there is a large amount of bromine in the septic tank, it is inevitable to install a water storage bay under the toilet, and there is a certain amount of water in the storage bay at all times, so that the water in the storage bay is isolated when the bromine goes up the sewage pipe.

If there is no inlet, the bromine gas will float down the toilet into the room, which will cause the house to be full of bromine!

The function of the trap is to prevent the gas in the drain pipe from coming out, and there are many functions of the trap at the same time. For example, to prevent stones or other large source items from falling into the drain, such as a mobile phone accidentally dropped, this is an accident. And if there is a blockage, it will generally be in the trap, and the trap has a check, which is easy to deal with if it is blocked.

The function of the trap is to prevent the gas in the drain pipe from coming out, and there are many functions of the trap. For example, to prevent stones or other large objects from falling into the drain, such as a mobile phone accidentally falling down, this is an accident. And if there is a blockage, it will generally be in the trap, and the trap has a check, which is easy to deal with.

The toilet bowl is also equipped with a water trap, so I don't have to worry about blocking

Shops that sell toilets sell special rubber seals for toilets. Like oil seals.

Now it's a one-piece toilet, and it's okay without an expansion screw. Plug those two holes.

The ground must be sealed.

You can make a flange first, put sealant around it, and then use that black sealing mud.

No problem, the upstairs are very good, pay attention to waterproofing!

Toilets are hard to find to screw these days!

Can be installed" recommends that you buy a toilet with straight drainage, as for the way there are too many, but none of them are too good.

To install the toilet with a flange ring, the sewage pipe must be sawed flat to the ground, and the maximum is less than 1cm. You can do this.

Yes, it doesn't have much impact!! It can be basically the same as the ground!!

Not a big problem, he has a kind of rubber seal that is connected between the toilet outlet and the drain.

Dear, hello, I have inquired for you, is the toilet installed in the bathroom a sewage pipe that does not need to be stored in the water bay Lu Yuanzheng? Answer; Yes "Yes, do not install a trap, and you must not install a trap, otherwise the toilet will be very easy to block. If you look at the structure of the flush toilet, it has a cavity with a loose water trap.

It can prevent odor from escaping. However, there is one thing that must be installed to seal the seam between the toilet bowl and the drain pipe, and that is the butter ring, otherwise because the drain pipe does not have a trap and does not have an anti-odor function, the odor will be emitted into the bathroom room through the gap. Butter rings, hardware in general.