How do you lay tiles without cement and sand?

Chimeric dry paving method: first set up grooves at the four corners of the tile, then fix the chimeric piece on the ground, install the two butt, and finally paste the adhesive on the back of the tile, which can prevent the tile from sliding everywhere and will be safer. Our home is decorated with floor tiles.

At present, almost all of the floor tiles in our country will use cement and sand. There are actually three ways to use cement and sand to lay floor tiles: the first is the most traditional wet paving method.

The second is the more popular dry paving method. The third is to use adhesives to lay floor tiles.

Due to the new ceramic tile auxiliary materials on the market, the use of cement and sand for pasting ceramic tiles is very few, and now the decoration of pasting tiles, the use of ceramic tile back glue, tile adhesive, new decorative materials. Due to the relatively short time to market of the two materials, the principle of tile paving is similar to that of a keel for paving floors, a steel skeleton with leveling screws. After the skeleton is ready, the foaming agent is applied to the skeleton.

Paste the tiles. The use of tile paving racks can be done without cement mortar.

Save on shipping, upstairs fees. Now the freight and upstairs fee of cement and sand are a high cost.

<> by using marble glue on the back of the tile.

Paste as a structural support, the construction process of dry hanging is very fast, the effect of the later stage is also very good, and it is very strong, it is rare to appear like a wet shop with a hollow.

or the case of a drop. But the cost of dry hanging will be higher, and then dry hanging needs steel structure priming will increase the share of space tile adhesive, 20-25 kg a bag, directly mixed with water, with a toothed spatula, a bag can be paved 3-4 square meters, the adhesion is 2-3 times that of cement, the bonding thickness is only 3-6 mm, no waste of space, the ratio of not using cement yellow sand began to slowly improve, tile adhesive is the main alternative. And now many users like floor tiles on the wall, whether it is a background wall.

Or the bathroom, they like to use the moisture content.

The lower glazed bricks are done, and they can be renovated after a long time, and the rich play time.

You can use the chimeric dry paving method: first set up the grooves at the four corners of the tile, then fix the chimeric piece on the ground, install the two butt, and finally paste the adhesive on the back of the tile, which can prevent the tile from sliding everywhere, which will be safer and more convenient.

The principle of tile paving is similar to that of a keel for paving floors, a steel skeleton with leveling screws. After the skeleton is ready, add foaming agent to the skeleton and paste the tiles. The use of tile paving racks can be done without cement mortar, saving freight and upstairs fees.

Now the freight and upstairs fee of cement and sand are a high cost. As long as the floor is slightly higher, the upstairs fee often exceeds the ** of sand. Last year, a six-story multi-story house cost 8,000 yuan for bricks and cement sand alone.

Another benefit of the tile paving hanger is that it can be installed quickly and the construction period is shortened. Some people may be worried about the strength and whether it is easy to step on, but in fact, it can bear the weight of a car after being installed flat. If it is a metal weight, the tile will cause damage regardless of the method of laying the tile, and it is relatively easy to replace it with a tile paving rack.

Do not use cement and sand to lay tiles, you can pave them overhead, that is, install the keel on the ground, lay the tiles on the keel, and then use adhesive to lay the tiles, directly on the ground to wipe the adhesive, and pave the tiles.

At this time, you need to use super glue, apply a little glue under the tile, and then cover the tile.

In addition to cement and sand, you can also use super glue or glass glue, first to make a skeleton, and then lay the tiles and penetrate the glass glue into the gaps between the tiles.

First of all, in terms of cost, cement is better than sand.

It is much more expensive, so adding sand and gravel will reduce some manufacturing costs.

Secondly, the thickness of pure cement is limited to less than 5 mm, and if it is too thick, it will flow. In addition, if the cement slurry is too thin, it is easy to lose water during curing and the strength is insufficient. The cost of pure cement slurry is higher, which is why pure cement slurry is not commonly used, and it can also be used with a small amount of quality assurance.

In addition, cement has dry shrinkage properties. Sand and gravel is an aggregate, which can not only improve the strength, but also inhibit the dry shrinkage and deformation of cement. When using pure cement, a big change in temperature and humidity in the following environment will quickly collapse, which is what we call a hollow drum.

Fall down! This is because it is said that wall tiles are not the same as floor tiles.

Different. Wall tiles are generally glazed with clay, which is not as strong or dense as floor tiles, with a relatively high water absorption rate and high adhesion to wall tiles. <>

It is not recommended to use pure cement for wall tiles, as they are much more demanding than floor tiles, and many decorators use pure cement to prevent trouble. The decorator told me that using pure cement will cause the wall to expand and crack, and pure cement paste is not as good as cement mortar.

Stickers are effective. If there is no thickness requirement, you should ask the home improvement master to use cement mortar to tile. <>

In general, it is better to use pure cement or add sand to the tiles on the wall, both of which have their own advantages, but it is better to add sand to the wall, because it can increase the adhesion of the tiles. And the addition of sand can also greatly reduce the cost, reduce the cost and improve the quality, that is naturally the best choice. But I have also seen the use of pure cement, tiles, and the effect is still very good, which is to make a choice in the quality of the tile, be sure to choose those tiles with strong adhesion, and better quality tiles, because there are some tiles after the completion of the paving Its water absorption is not strong, so it will cause it to be hollow, and it will fall off after a long time.

If it falls off, it will be very serious, and if it hits us, it will be a very big thing.

You need to choose cement and sand first, because when you use pure cement to pave tiles, it will absorb the surrounding moisture when it hardens, which will become tight, causing the tiles to fall off. Cement sand will not appear this problem, it can ensure that the tile paste is stable, the actual operation should be in accordance with the order from bottom to top, from left to right, and the tile should be soaked in water for more than half an hour before construction, so as to ensure that the small holes of the tile fully absorb water, avoid the absorption of water in the cement after paving, resulting in the situation of falling off.

No, this will affect the performance of tile adhesive, and the adhesion will decrease. During construction, special attention should be paid to the workers and not to let them mix cement in the tile adhesive.

The main reasons for the general workers to add cement in the construction of tile adhesive are: to speed up the drying time of ceramic tile adhesive, to make the ceramic tile adhesive paste become delicate, and to paste tiles is better to knead and press, cut corners and reduce costs. As the saying goes, the speed of speech is not reached, tile adhesive contains a lot of water-retaining components to ensure the increase of adhesive adhesion, adding cement will greatly reduce the adhesion, resulting in hollowing.

Drop bricks. JCDecaux tile adhesive takes into account the construction habits of the master, and fully takes this into account in the formula design, compared with other tile adhesives, fast drying is the characteristic of JCDecaux tile adhesive. Therefore, if you use JCDecaux tile adhesive, remember not to mix it with tile adhesive, so that the effect of tiles will be greatly reduced, and there will be the above-mentioned hollow drums, bricks and other phenomena.

Hello dear, the tiles can be glued with cement and sand on top of the tiles. Step 1: The surface of the floor tiles needs to be chiseled.

The so-called chiseling treatment is to use an electric drill to chisel on the surface of the original floor tiles, and kick the surface of the original floor tiles into wool. As a result, there is no glaze layer at all. Step 2:

It is carefully inspected after the surface of the original floor tiles is processed to check whether there are hollow tiles, and if it is found that the original floor tiles have hollow drums, these hollow bricks must be removed. Step 3: It is recommended that you use cement mortar to level the ground.

It doesn't have to be very thick, just a thin layer. Of course, this is only a personal suggestion, and it is also possible to leave it unbalanced.

No. There are two kinds of cement sand ratios for tiling, one is wall tiles, the other is ground tiles, under normal circumstances, the ratio of wall cement sand is 1:4, and the proportion of ground cement sand is 1:3;

1. Pay attention to the order of paving tiles, wash the surface of the wall and floor, and smooth the bottom with cement mortar.

2. Calculate the number of tiles, determine the pavement baseline, and pave them in order from bottom to top along the wall, with a joint of 1-3 mm.

3. The spacing of tiles can be adjusted according to the actual area, so that the corners are all made of whole bricks, which is time-saving and beautiful.

4. After the bricks are placed, hit the surface with a rubber hammer to make it sticky, and after the tiles are solidified and sticky, they can be cleaned with white cement caulking.

No.

The key point of the traditional ceramic tile wall, using cement and sand on-site mixing as a binder, lies in the ratio of cement and sand. According to the technical requirements, the cement and sand should be 1:2 or, so that the strength of the paste can be guaranteed.

In this way, the siphon phenomenon generated by the cement hydration reaction is used to stick the tiles. Therefore, it is suitable for glazed tiles with high water absorption. At present, in the low-end decoration, this way is still commonly used to pave tiles, and its material cost is about 10 square meters.

Definitely not, the cement is likely to tear the tile when it sets.

According to the thickness of the paving tiles, the amount of cement sand that needs to be used is also different, if calculated according to the thickness of 30, the water capacity mud that needs to be used in one square is about 11kg, and the sand that needs to be used is about, the specific calculation formula is as follows: sand amount = thickness * paving area, and the amount of cement is generally one-third of sand.

Masonry construction is a very important part of the decoration process, if the construction is not in place, it is easy to affect the later use, so before the construction, we must first understand the amount of materials and construction skills to ensure high-quality construction quality.

Ichiping bai

Square floor tiles are needed.

Kilograms of cement du, kilograms of sand.

A square wall tile needs kilograms of cement and kilograms of sand.

One square floor tile bai requires kilograms of cement.

du, kilograms of sand.

One square wall tile requires kilograms of cement and kilograms of sand.

One square meter of floor tiles need cement kilograms of sand, one square wall tile needs cement is kilograms, 12 kilograms, including reasonable loss, the average family due to the simple operation of the wet paving method is low, many families use the wet paving method to pave the floor tile surface.

According to the calculation of 50 catties of 1 bag of cement, from a bag of cement can be paved 2 floor tiles, that is, 1 to 25 catties of cement, according to the ratio of 1:3 to calculate the need for 75 catties of yellow sand. Therefore, it takes 100 catties of sand cement to paste 1 floor tile.

The history of ceramic tiles should be traced back to BC, when the Egyptians began to decorate various types of houses with ceramic tiles. Clay bricks are dried in the sun or baked and then colored with a blue glaze extracted from copper.

Ceramic tiles were also found in the Mesopotamian region BC. The tiles were decorated with blue and white stripes, and later appeared in a variety of styles and colors. China is the center of ceramic art, and a fine type of white stoneware was produced as early as the Shang and Yin periods.

Generally, one square of flooring should be used.

The ratio of cement and sand is 1:2 or 1:3, a pack of cement is about 3-4 square meters, if it is calculated according to 4 square meters, it is 25 catties of cement, and the sand is 50-75 catties.

Bai decoration when cement.

The ratio of du to yellow sand is 1:3, calculated according to 50 catties of 1 bag of water and mud, a bag of cement dao

The floor tiles that can be paved 2 are 25 catties of cement to be paved 1, and 75 catties of yellow sand are required to be calculated in a ratio of 1:3. Therefore, it takes 100 catties of sand cement to paste 1 floor tile.

The floor tiles are made of No. 325 cement, with a strength grade of 1 3 hours and a final setting time of 4 6 hours.

You can calculate it yourself, but it has a lot to do with whether your ground is level, you can use 1:3 cement mortar, but it is recommended that you use dry and hard, which is not easy to produce hollow drums.

The thickness of pouring 26 square meters of floor slab with 7 bags of high-standard cement is 11 cm, if it is a floor tile, 50 square meters have 5 bags of cement and 18 bags of sand are enough, 100 square meters have 10 bags of cement and 35 bags of sand are enough, and the thickness of 3 cm is pasted. Wait a minute, someone will say I'm digging a grave.

This depends on the height of your ground, and the sand and cement are different on different floors, and the higher you go, the more expensive it is.

It is 1 bag of cement and 3 bags of sand can be paved 3-4 squares.

If you don't use cement and sand to lay tiles, what other ways are there to lay them?

If you don't use cement and sand to lay tiles, what other ways are there to lay them? Kiss! Hello, glad to answer for you.

1. In addition to the use of cement mortar, you can also use tile adhesive for paving. Tile adhesive has the advantages of high bonding strength, water resistance, aging resistance, etc., and is mainly used for pasting decorative materials such as walls and floor tiles. When we use tile adhesive to lay tiles, the tiles do not need to be soaked in water in advance, unless the base surface or the tile is very absorbent.

Tile adhesive should be stirred with an electric mixer, and it needs to stand for 5-10 minutes after mixing, so that the adhesive of ceramic tile adhesive can be maximized; It is best to use up the stirred tile adhesive within 1-2 hours before it is rushed. 2. When you paste tiles, you can also choose to dry hang the tile pavement branch sweeping method, dry hanging tile is the use of metal pendants to fix the tile on the wall; This pavement method is not only convenient for construction, but also can make the tile maintain excellent performance and avoid the problem of tile hollowing; Moreover, the firmness of the tile paving is very good, which can reduce the bearing of the wall, etc. However, the dry paving method is more technically high, and its cost is relatively more expensive.

3. According to Qeeka Home experts, acceptance is required after the tile is paved. We need to check whether the surface of the tile is smooth, clean, harmonious in color and luster, and firmly pasted; whether the tile joints are dense and smooth; Whether the reserved hole is the correct size, the edge is neat, etc. You can also use a ruler to check the flatness of the wall and ground, usually the flatness of the wall tiles and the verticality of the façade error can not exceed 2mm; The error of the floor tile should not exceed 1mm and so on.

Hope mine can help you! Do you have any other questions?