What to do with the glare left by the car polishing

The steps for grinding and polishing are as follows:

1. Clean the whole vehicle. Clean the whole vehicle with a paint cleaner with strong detergency, and when using the cleaning agent, you should avoid new scratches caused by particle dust in the grinding.

2. Water sandpaper grinding. For defects such as coarse grains, fine sandpaper marks, flow marks and other defects on the painted surface, wrap 600 water sandpaper in water in a small rubber liner before polishing, and gently polish it until it is smooth (note that it cannot be worn through the paint layer).

3. Coarse and fine grinding. Use a mechanical grinder (electric or pneumatic) plus coarse abrasive paste to coarsely grind the traces of water sandpaper; Then add abrasive paste to polish and polish fine grinding.

4. Polishing. A mechanical polishing machine is used to remove the spin marks left by the coarse abrasive paste with a mirror treatment agent to achieve the effect of mirror polishing of the paint film.

5. Hand glazing. After grinding and polishing, wipe off the grinding and polishing paste, immediately wipe all the polished parts with cotton yarn dipped in varnish wax, and then wipe off the excess varnish wax with dry cotton yarn to make the paint surface bright and dazzling.

In order to make up for these defects, grinding and polishing are usually carried out after spraying, so as to improve the mirror effect of the paint film and achieve the requirements of brightness, smoothness and showiness.

Extended information: Car polishing is the process of car beauty, in the process of waxing, glazing or coating, first polishing the car. Because the glaze coating must be polished first, and it is a finely polished car before it can be made into a mirror.

This is the operation that the glaze must go through. Without polishing, the paint is uneven, and the glaze retention time is very short, and it cannot have the effect of long-term adhesion at all, which is no different from waxing. Of course, according to the situation of the car paint, polishing does not have to be done in all three steps, and new cars often can be restored in one step.

However, the car that has done coarse wax must be polished with medium wax, and the car that has done medium wax must be reduced with fine wax.

At present, the market demand for automobile polishing is very large, but the first aspect is slightly insufficient, especially with core intellectual property rights, there are not many enterprises with excellent product quality, and the industry as a whole lacks brand effect. In the stage of strong demand, there is no doubt that the industry demand is huge and the development prospects are good.

However, how to maintain the health, stability and sustainable development of the industry requires the joint efforts of enterprises in the industry, especially the need to give full play to the fastidious research and development spirit, further improve the production process, reduce costs, truly solve the practical difficulties of customers, strictly control the quality, and provide the most reliable products.

Let me tell you.

Traditional polishing is to polish brightness, throw oxide layer, cover it with abrasives, and then wax it to make a sealing glaze, and it is invisible.

If the plating is degreased, the scratches must be there.

And then what to do?

To use alumina water-based abrasives, Japanese short wool flat polishing treatment, ultra-fine sponge reduction disc to do reduction, this can be processed. If you can't do it yet, I recommend learning the polishing technique of the system.

Check the polishing technology: polishing does not shake the plate and does not knock the plate You can throw away 1500 sandpaper prints Degreaser degreasing without dazzling lines In order to achieve a professional polishing level.

Hello, the polished aperture is the need to use a paint reducing agent.

It is more convenient to deal with it and then wax and maintain it, or it is more convenient to polish it directly with abrasives. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

After polishing, the next step is to restore the paint finish. First of all, use a low-speed polishing machine, with a wave sea surface disc, with a mirror reducing agent (the reducing agent is divided into dark paint and light paint according to the color of the paint with the corresponding mirror reducing agent), on the paint surface of the tic-tac-toe polishing. Pay attention to the polishing temperature.

Then the car wash acceptance. It's not a question of avoiding or not avoiding. After polishing, the paint surface should be restored.

Light-colored cars are not noticeable. But there will be. But some grinders do not have spiral lines after polishing.

Because the grinder is oily. But it will still appear after washing the car. Therefore, after polishing, it is necessary to do paint restoration.

Then there's waxing, glazing, coating, and things like that. Ordinary beauty shops do it.

This has a lot to do with the polishing machine, abrasives, sponge discs used. If you are only using the traditional polishing process (rough polishing + fine wax), it is recommended to use medium abrasives and light polishes, and finally apply a layer of protective agent.

How to eliminate the glare pattern in car polishing Treatment method of glare after polishing of automobile glass: 1. The next step after polishing is paint reduction, first of all, use a low-speed polishing machine, cooperate with the wave sea surface disk, use a mirror reducing agent (the reducing agent is divided into dark car paint and light car paint according to the color of the car paint with the corresponding mirror reducing agent), polish the tic-tac-toe on the paint surface, pay attention to the polishing temperature; 2. Then carry out car wash acceptance, this is not a problem to avoid or not, after polishing, the paint must be restored, and the light-colored car is not obvious, but there will be; 3. However, some grinders do not have spiral lines after polishing, because the grinder is oily, but it will still appear after washing the car; 4. Therefore, after polishing, the paint must be restored, and then there is waxing, glazing and coating, etc., which are generally done by beauty shops. @2019

Glare from car paint.

The pattern will affect the beauty of the car, and the reason why there will be a good vortex pattern (dazzle pattern) next to the swirl is mainly because there is a problem with the polishing disc used in the polishing of the car, which is naturally more likely to produce the swirl lead vortex pattern. The best way to eliminate car spiral patterns is with a little wax, which, during use, must be applied evenly over the paint.

If the car is not specially polished, it may be caused by human factors, the other is naturally occurring wrinkles, and there is also a kind of Qin that is caused by the lack of skill of the construction personnel when grinding. The glare pattern formed by the paint is caused by the incorrect way of washing and waxing, or the dust and other impurities in the air scratching the car.

If the scratch is shallow, you can throw it away, but if the primer or scratch master can't run away.

The glare after polishing of the car should be restored to the paint surface.

The next step after polishing is paint reduction, first with a low-speed polishing machine, with a wave sea surface disc, with a mirror reducing agent (the reducing agent is divided into dark paint and light paint according to the color of the paint with the corresponding mirror reducing agent), polishing on the paint surface in the middle of the tic-tac-toe, pay attention to the polishing temperature.

Then carry out car wash acceptance, this is not a problem to avoid or not, after polishing must do paint restoration, light-colored cars are not obvious, but there will be, but some grinders do not have spiral lines after polishing.

Because the grinder is oily, but it will still appear after washing the car, it must be done after polishing the paint restore, and then waxing, glazing and coating, etc., which are generally done by beauty shops.

Precautions for car polishing:

1. Clean the whole vehicle, clean the whole vehicle with a paint cleaning agent with strong detergency, and avoid new scratches caused by particle dust in the grinding when using the cleaning agent;

2. Water sandpaper grinding, for the coating surface has coarse grains, fine sandpaper marks, flow marks and other defects, before polishing, use 600 water sandpaper dipped in water to wrap in a small rubber pad, and gently polish it to a flat (note that it cannot be worn through the paint layer);

3. Coarse and fine grinding, using a mechanical grinding machine (electric or pneumatic) plus coarse grinding paste to coarse grind the traces of water sandpaper; Then add abrasive paste to polish and polish fine grinding.