Why does the trap keep spraying water all the time

Here are some of the well-known brands recognized in the valve industry, which are widely recognized and have a high reputation. While rankings may vary depending on time and market conditions, the following brands are generally considered to be among the top brands in the valve industry:

The following influential first-line brands of water system valves and industrial valves can be used as a reference, but for reference only: Suzhou Neway Valve, Shanghai Guanlong Valve, Shanghai Qizhong Valve, Sanhua, Su Yan, Shentong, Su Valve, Nanfang, Jiang.

First, the word Yao. The above manufacturers are only estimates and references, and the specific situation may vary or fluctuate at any time due to changes in a series of factors such as changes in the market, the size of the competition pattern, and the stability of product quality. As an indispensable key device in industrial production and civil facilities, the quality and reputation of the valve brand directly affect the satisfaction and trust of users.

These brands are known in the valve industry for their innovative technology, high-quality products and reliability. It is important to note that the market and industry are evolving rapidly, and different rankings may vary depending on time and region. For the most up-to-date ranking information, it is recommended to refer to industry reports, professional organizations or market research data for more detailed and accurate information.

The displacement of the trap is not small.

When it is found that the trap is not working, and the cause cannot be found, attention should be paid to the discharge of the trap. If the trap is fitted with a test valve, it is relatively simple to inspect. Otherwise, the outlet connection line should be opened.

Fault symptoms and handling methods:

Cold valve – does not drain.

Heat valve – does not drain.

Steam loss. Continuous discharge.

Heat slowly. Inexplicable question.

Get rid of illusions.

Cold valve – does not drain.

a If the trap cannot discharge condensate, then:

The original design pressure is incorrect.

The pressure is increased and a smaller orifice is not installed.

The pressure reducing valve is out of order.

The boiler pressure gauge reads low.

After normal wear, the seat bore is enlarged.

The high vacuum within the return line increases the differential pressure that exceeds the operating differential pressure of the trap.

b Condensate or steam does not enter the trap.

The filter in front of the trap is clogged.

There are other valves damaged on the line where the trap is installed.

Clogged lines or elbows.

c Mechanical wear or defect that needs to be repaired or replaced.

d The trap body is blocked by dirt, and a filter should be installed to drain the drain.

e For inverted bucket traps, the following measures should be taken when the vent hole of the floating bucket is blocked by dirt:

Install filters.

Enlarge the vents a little.

Place a wire in the exhaust hole.

f For float traps, if the air vent is not smooth, air blockage will occur.

g For thermostatic traps, the bellows element may be damaged due to water hammer, causing the trap to shut down.

h For disc traps, the traps may be installed upside down.

The above one is that the cold valve does not drain water, so if you don't have a conversation, you will ask again.

There are many reasons why the trap does not work, and the general judgment direction can be divided into 1Damage to the trap itself (including clogged filters) 2When the operating condition of the trap changes, check whether the pressure difference between the front and back of the valve is within its performance range.

3.Design issues caused the trap to produce steam bindings and air binding4I didn't choose the type well.

The specific reason still needs to be investigated according to on-site analysis, so it is difficult to say clearly.

The function of the trap is to block the steam drainage, and now it is not drained, there is only one reason, the pipeline is not passable or the trap is blocked.

Cleaning pipes or traps is the only option.

Summary. A higher outlet than a trap can lead to the following consequences:

A higher outlet than a trap can lead to the following consequences:

1.Traps do not discharge water properly: Traps are used to drain water that has accumulated in equipment or pipes.

If the water outlet is higher than the trap, the Chunxiao trap will not be able to discharge water, resulting in water accumulation inside the equipment or pipes, which may cause damage to the equipment or blocked pipes. 2.Reduced hydrophobic efficiency:

When traps do not drain water properly, water accumulation inside the equipment or piping increases, reducing trap efficiency. This can lead to problems such as reduced system efficiency, shorter equipment life, and wasted energy. 3.

Increased maintenance costs: Accumulation of water inside equipment or pipelines increases the risk of equipment failure and requires more frequent maintenance and overhauls. This will increase maintenance costs and downtime, and reduce production efficiency.