The groove under the balcony window will accumulate water when it rains, how to solve it?

The master who overhauled my home saw at a glance that the window leakage was not the problem that the window was not installed with sealing strips, but the decoration must have been caused by the exterior wall cement and then the window frame installed: the window frame and the size of the window hole do not match, the balcony leaks, I believe that many of you have encountered this situation, and some people don't know what to do, but the workers are responsible for it cleanly! It turned out that the worker saw that his friend was a layman, so he only put some sealant on the sealant of the window, and did not find out the cause of the leakage on the top edge of the window.

How can this be solved? Let you get it done quickly with a few tricks! I've also seen the outside looks good, but it's still leaking, now some workers in order to save trouble, when working, after installing the window and then plastering the slope outside, only care about the face, when you use it to mix, 10 hours to dry, after drying like iron, press to the seam inside it, everyone pay attention to send me a private message, send ** to everyone.

It is also sold on a certain treasure. It is necessary to find out the cause of water leakage, and then confirm it one by one according to the investigation method, and finally find the cause of water leakage, and solve the water leakage problem symptomatically, so that it is the best maintenance plan! Fourth, it is the window frame of the window, did the master hit the expansion screw when he fixed the lower mouth of the window frame, and if he did, did he block the head of the expansion screw with sealant, and the waterproof water leaked through the screw hole.

If the lower part is leaking, you need to see whether the platform outside the window has gone on the slope, if not, brush some waterproof paint, and then use cement to wipe the slope, and finally put glass glue on the joint between the window and the slope.

I don't understand, can you be simple and clear: there is generally a drainage outlet outside the lower window frame, if the rainwater is blocked, it will flow in, you can find a wire to try! Summer is the rainy season in the traditional sense, with many stormy and rainy weather.

At this time, window leakage becomes a problem that annoys many people. The causes of window leaks are different, and the solutions are different. I have also seen that the outside looks good, but it is still leaking, and now some workers only care about face when they are working, when they are working, they install the windows and then wipe the slope outside.

If there is no drain hole, it will lead to water accumulation, you can drill the drain hole so that the water can flow out, and if there is a hole, check whether the drain hole is blocked.

Water can be scooped out. The recesses under the balcony windows often accumulate water when it rains, so you can scoop it out in some container or connect it with a water hose.

You can buy some sponge blocks and wash the water out when the rain stops to prevent the water from soaking the grooves, and you can also manually make a platform on the window to protect yourself from the rain.

It can be treated by adding drip eaves, unclogging drainage holes, repairing windows, redoing waterproofing, sealing window frames.

1. Increase drip eaves. If the window is renovating the balcony, the window is pressed to the dripping eaves and rains, it will enter the window frame and infiltrate the wall, and it is necessary to add dripping eaves at the window.

2. Dredge the drainage holes. If the drainage hole at the bottom of the plastic steel window is blocked, it will not be able to be discharged normally when it rains heavily, so you can dredge it.

3. Repair windows. Water seepage occurs when the quality of the window is loose and it needs to be reinforced or replaced.

4. Redo the waterproof layer. The waterproof layer around the window is damaged, and the wall waterproofing function fails, and water seeps out, so the waterproof layer needs to be redone.

5. Seal the window frame. If there is a problem with the sealing strip between the window and the wall, water will seep into the interior and the sealing strip will need to be resealed.

The irregularity of the window installation leads to the problem of pinning the mold.

There are many reasons for this phenomenon, such as the specification of the window production department or the installation is not standardized, etc., which can cause it to leak. The loss is said to be non-standard in the production department, which means that there are no drainage holes in the windows, so that when it rains, the rainwater cannot be discharged, resulting in water leakage. In addition, when installing windows, the splicing is not sealed properly, resulting in leakage.

Most of the reasons for the leakage of the window sill are caused by quality problems, and in this case, you can only ask someone to repair it or replace it with a new one. In addition, when purchasing window sills, it is necessary to pay attention to the quality of whether it is a window frame, a window sash, or a sealing material.

If the window sill is leaking due to the gap between the wall and the window frame, it is necessary to re-apply foam glue to seal it. Clean the old sealant before injecting the new sealant. However, if it is caused by the gap outside, then after using the sealant, it needs to be sealed with cement mortar, so as to play a waterproof role.

In the process of use, many home window sills will leak due to clogged sinks, in this case, you only need to clean up the blockage and keep the drainage smooth. If there is a problem with the original drain hole, you can close it and open a new hole.

There is abundant rainfall in spring and summer, so there are often rainy days, especially when it rains very frequently, and the rainfall is also very heavy, and if there is wind, it will blow on the windows. If the window slots are filled with water, the water will flow into the room. So how to solve this situation and avoid it?

1. What should I do if the window groove is waterlogged

1.Clean the grooves. The inside of the groove must be kept clean and there must not be too much solids in it so that rainwater can flow in the groove instead of piling up together. In some places where it is impossible to unblock, screwdrivers and other tools can be used.

2.Unclog the drain hole, there will be a small hole in the recess on the outside of the window. The purpose of this small hole is to drain the water that has entered the groove. If you suspect that there are bugs in the drain hole, you can buy a window drain filter online and attach it.

3.Choosing a water baffle and installing it on the inside of the window will increase the depth of the recess, which will allow the window recess to have a stronger water storage capacity and drain the drain holes. When changing the window, you can also select a deep grooved window.

2. What should I do if water will enter under the window when it rains

1.When water gets into the window recess when it rains, it is essential to check that the window sealant has been deglued. If it is due to the degumming of the sealant, it can be reglued again.

2.Check the window seals for age. Users can try it, if the seal breaks or is brittle when pulled, it means that it has been aging for too long, or if you have purchased an inferior sealant, you need to buy a new seal.

3.Check the room seal of the window. If the original window has not been modified, you can look for a leafless for inspection. This means that their quality is not good enough, and users also have the option to replace the windows with new ones.

3. How to prevent window leakage

1.Strict control of quality: It is necessary to strictly control not only the quality of the windows, but also the window frames and sealing strips.

2.Install correctly: The outdoor window sill should be lower than the indoor window sill, the height should be 20mm, and the water slope should be set, and the window frame should be tightly sealed to prevent water leakage.

3.Reseal window seams: If it is due to a poor seal, reseal the leak.

It's best to wait until the weather is good, clean the dirt inside, and then fill it with weather-resistant glass glue. Seal it, and if it's outside the window, it should be waterproofed and sealed with mud and mortar.

4.The window groove should be cleaned frequently: if there is water in the window groove, it may be due to the lack of attention to the hygiene of the window groove on weekdays, resulting in the blockage of the drainage hole; If there are no drainage holes, they need to be cut to facilitate drainage.

What to do if the window sink overflows into the room

Heavy rain, balcony aluminum alloy window groove water accumulation, so that leakage into the house, the reason is that the sink is serious water accumulation, poor drainage leads to joint leakage.

As an aluminum alloy window, it is divided into casement window and sliding window according to its structure. The aluminum alloy window groove is waterlogged is a sliding window series. The said sink is present on the slipper, and there are two tanks that will accumulate water (as shown below).

The water from the two sinks will be discharged through the water holes opened in the high and low slide rails - usually windows of less than three meters, and two drainage outlets are reserved for each track. When rainwater accumulates in the trough, it flows out through the water holes. However, when the water hole is blocked, the joint between the two ends of the slide and the winger will leak out through the gap in the sealant, causing water to enter the room.

Treatment method: 1. Check whether the water outlet hole on the slide rail is blocked, and dredge it;

2. Check the gap between the two ends of the slide and the side seal, and re-close it with sealant.

Other precautions: If it is a leaking casement window with an inward opening, please check whether the sealing strip around the frame is aged (as shown below) and replace the adhesive strip to prevent water leakage.

This is because there is no drain hole. Rainwater enters along the junction between the sash and the window frame (rainwater sucks in due to the imbalance between indoor and outdoor air pressure) or the adhesive strip on the outside of the glass.

Resolution. 1: Open the outer frame of the fan to punch holes to balance air pressure and drain water.

2: Glue the outside of the glass.

Buy a black silicone sealant, it's cheap. If you want to do it yourself, it's best to buy another roll of "masking paper". If the glue is painted, it cannot be washed off with water, so use alcohol.

If the balcony aluminum alloy window sliding window groove is waterlogged, use a hand drill to make a few more small holes in the window groove slideway, which can be solved.

Slotted eyes, sealing problems. One is to cut a slotted eye outside the window, and the other is to seal it. Very simple.

Water flaps can be added to the windows!

Most of you are this because you didn't close the windows and the rain filled the aluminum alloy frame! The average aluminum window does not have a sink! The water won't flow out! This is the consequence of greedy for cheapness, if you want to completely solve the problem, replace the window, if you dispose of it at will, install a canopy above the window, or directly install water retaining on the outside of the aluminum alloy tank, or do it yourself! Drill a few holes on the outside of the window to help drain the water, and be careful not to get into the aluminum frame!

What to do? I recommend that you decorate it with a marble slab, which is both practical and beautiful. Of course, if the rainfall at both ends of the slate is greater than the drainage capacity of the floor drain during heavy rain and typhoons, it may cause water to accumulate on the balcony floor;

Add the canopy, a smaller one is good, save trouble.

Your problem should be that the drain is blocked, you check it and see if you can get through it one by one.