How to remedy the wall cabinet made at the head of the bed? How to solve the problem that the bedsid

As long as you abandon feudal superstition and believe in science, you can move the bed, or change the position of the hanging cabinet and it will be resolved, if you don't have superstitious thoughts, you won't care about these things. Therefore, by believing in science and abandoning feudal superstitions, you can live a happier life. I wish you happiness.

Put the bedside table in another place and put a small plastic stool next to the bed!

1. Don't want a bedside table, this method can also be used, that is, the two sides of the bed are asymmetrical, and you don't need a bedside table to find a way to solve the problem of charging a desk lamp or mobile phone. It is also a solution.

2. Do a sliding door! This is the most used solution.

3. Open the door on the side, only the one on the left, and reach in to get the part of the clothing that is blocked. The downside is that it's not particularly convenient.

Shelving or floor lamps with shelves.

The wall cabinet has a certain storage effect, can the wall cabinet be installed above the head of the bed? Today, I will answer them one by one for you.

Above the head of the bed is a wall cabinet that can be thickened. However, there will be certain pros and cons of installing wall cabinets, which are as follows:

1. Advantages: Installing a wall cabinet above the head of the bed in the bedroom not only does not waste the white wall, but also can have more storage space; And compared with the floor-to-ceiling bedside table purchased in the Shiwei market in the town, this one is better and more beautiful.

2. Disadvantages: Imagine that there is a hanging cabinet above the head, and you will feel a sense of depression when you sleep, which is more uncomfortable; And it is also necessary to consider its certain safety, if the installation is not good, there will be certain safety hazards.

Summary. Turn the bedside table upside down, install the sheet in its original position, and then use a few iron nails to fix it on the cabinet board from the inside out, so that the iron nails that are not fixed in part can support the thin board.

Turn the bedside table upside down, install the thin board according to the original position, and then use the cover to carry a few iron nails from the inside to the outside of the orange cabinet board, so that the iron nails that are not fixed in can support the thin board.

The installation of each type of headboard is different, and most of the headboards are. Dual-purpose is not only the headboard, but also friends can be opened, there is a storage box inside, like this, it is generally the lotus leaf loose will fall down, and the loose lever will also fall down, replace the screws or holes to reinstall it, but if it is not this dual-purpose paneling, that is, from the reverse side that is to take out the head of the bed first, and then you can see the position of the screw lock from the reverse side, that is to say, the headboard that can fall down, that is, the position of the lock connection is loose, so it will fall off, It is recommended to put this lock on the inside. The lever base that has been put into the lock, and then squeezed into it with oil-based glue for bonding, and after a few minutes, the bond is firmly bonded and then installed on the wheel.

It's best to find a carpenter to replace it directly or buy a new one. Even if you barely connect it, it will be broken.

Summary. 1. Detect whether the whole is consistent with the design plan, whether the internal pattern is consistent with the plane plan, and whether there are surface bumps and scratches.

2. Test details: such as whether the handle is missing (don't be surprised, for example, in a U-shaped cloakroom, N doors in different directions are very likely to be missing), whether the opening and closing of each door is smooth, the gap between different shapes, etc.

For the important link of dismantling and installing furniture, it is mainly mastered from the front, middle and back, that is, the preparation before dismantling and installing furniture, the operation in the process, and the subsequent detection. In this link, we must be careful and careful, pay attention to safety, do not be reckless, and install furniture in the process of protecting ourselves. Of course, if in this process, if there is really no way to install it yourself, it is better not to do it brutally, or contact the relevant professional decoration master to help.

What should be paid attention to when the wall cabinet above the bed head of the newly renovated house is removed this year?

1. Detect whether the whole is consistent with the design plan, whether the internal pattern is consistent with the plane plan, and whether there are surface bumps and scratches. 2. Test details: such as whether the handle is missing (don't be surprised, for example, in a U-shaped cloakroom, N doors in different directions are very likely to be missing), whether the opening and closing of each door is smooth, the gap between different shapes, etc.

For the important link of dismantling and installing furniture, it is mainly mastered from the front, middle and back of the field, that is, the preparation before dismantling and installing furniture, the operation in the process, and the subsequent detection. In this link, we must be careful and careful about the infiltration ridge, pay attention to safety, do not be reckless, and install furniture in the process of protecting ourselves. Of course, if in this process, if there is no way to install it yourself, it is better not to do it brutally, or contact the relevant professional decoration master to help.

Hope mine is helpful to you.