Moving toys are handmade, handmade toys are made

As follows: 1. Draw a butterfly on the hard paper, add a rectangular handle on the inside of the wings, and cut out the butterfly with scissors according to the outline after drawing;

2. After the left wing is cut, make a short handle and use double-sided tape.

or transparent glue glued to butterfly wings;

3. Merge the left wing and the right wing;

4. Cut out the butterfly and paste it on the front of the model;

5. Pinch the long handle with your hand, pull the short handle back and forth, and the butterfly moves.

Cardboard chicks. In the past, we made round cardboards, folded in half, and glued to the eyes to be a cute chick; Now fold the cardboard regularly, glue the wings, and another kind of cute chicken comes out.

The handmade method of jumping toys is as follows: tools Raw materials: square colored paper, pens.

1. Prepare a square piece of pastel paper and a black pen. 2. Fold the four corners of the square in half to the middle and open them into two diagonals in the middle. 3. Fold one corner of the square upwards to form a triangle.

4. Pinch the midpoint of the bottom edge with your hands, squeeze the left and right corners into the middle, and fold them into the following triangle. 5. Fold the left and right corners of the upper layer upwards and fold them into a square. 6. Fold the left and right sides of the square upwards.

7. Fold the two corners in the middle to the two sides to form the frog's two front legs. 8. Turn the colored paper over and the other way around. 9. Fold the left and right corners in half.

10. Fold the two corners in the middle to the two sides to form the two hind legs of the frog. Ten.

1. Fold the frog's tail back a section. Ten.

Second, fold the part that was folded to the back back back for a short period of time. Ten.

3. Use a pen to draw two dots on the frog's head to indicate the eyes, and the frog that can jump is done. Press the tail of the frog and as soon as you raise your hand, the frog jumps forward.

How to fold the purring flying bird: The flying bird, flapping its wings, it is about to take off! Fly to**, I don't know this very well Prepare two rectangular cardboards, one long and one short, 2 semi-circular cardboards, and a diamond-shaped cardboard After making the shape in the picture, paste the corresponding parts one by one, and the bird will be completed.

How to make handmade toys:

Materials and tools: cardboard, straws, balloons, hot melt glue guns, bottle caps, small sticks, tape, scissors, pen knives.

1. Make a car shape out of cardboard.

2. Then use a pen knife to dig two holes in the bottle cap, insert two straws, and fix them with hot melt adhesive.

3. Place the cap on the hole on the top of the car.

4. Make car wheels out of straws, sticks, and bottle caps.

5. Put the balloon on the bottle cap and fix it with tape, and the car is done.

An overview of handmade toys

Handmade toys can be understood in a broad or narrow sense, and handmade toys in a broad sense include toys that are completely hand-made by the producer without the help of mechanical force in the production process, such as self-sewn dolls, self-made Kong Ming lanterns, etc., as well as toys that toy consumers need to assemble by themselves, such as model airplanes, model ships, cross-stitch, etc.

Handmade toys in a narrow sense only refer to toys that toy consumers need to assemble by themselves to realize their game value or ornamental value. With the approach of the era of knowledge economy, handmade toys carrying the connotation of unique knowledge value are increasingly popular among consumers in the toy market with a wide range of categories because of their uniqueness and educational characteristics.

Toys generally refer to objects that can be used to play, and playing with toys is often used as a way of entertaining and educating in human society.

Here's how to make handmade toys:

1. Toy name: kitten fishing

2. Suitable class: large class.

3. Toy letter beam function:

1. Understand the penetration and iron absorption of magnets.

2. Decompose the number within 10 to understand the relationship between the whole and the parts.

Fourth, grinding materials and methods:

Take a shirt box, lay the bottom flat, stand up as a background (decorated with various patterns on it), and then make a box slightly shorter than the box with cardboard, hollow out into water ripples (fish fished out of the water ripples) and paste aquatic plants and bubbles, etc., buckle the inside of the bottom of the box, and put a small fish with paper clips and numbers written on the body between the two; Take another straw and tie a magnet to make a fishing rod; A small box is attached around the bottom of the box, and the box has a digital card that can be replaced.

5. Toy play:

1. Drag the fish in the box with a fishing rod in the direction of the water ripples, catch the small fish, and put it in the surrounding small boxes, so as to understand that the fish can be caught through the cardboard and understand the penetration of the magnet.

2. Paste the numbers on the small boxes around the bottom of the box, and after the children catch the fish, the numbers on the fish are combined, and the number is put into the small box with the number of slippery and lucky words. For example, if the numbers 1 and 7 are on the fish, they are placed in a small box with the number 8 labeled on it.

Benefits of playing with handmade toys:

1. It can improve children's hand-eye coordination and graphic color recognition ability.

2. The training of spatial concept and logical thinking ability is conducive to multi-level thinking.

3. Cultivate children's concentration and endurance.

4. Long-term games are conducive to the health of the left and right brains and activate brain cells.

Children's handmade toys are very simple through children do it themselves, assemble, create, and make the type of toys, Zhideyou children's handmade toys include: vinyl dolls, handmade paintings, archaeology, diamond paintings, button paintings, velvet flowers, ultra-light clay, flannel bags, snowflake mud paintings, twisting sticks and so on.

Here's how to make handmade toys easily and fun:

1. Use scissors to cut the straw into two sections according to the width of the bottle, each section is a little longer than the width of the bottle.

2. Apply the hot melt adhesive evenly on the straw, and stick the straw with the hot melt adhesive on the bottle.

3. Install four wheels for the car, first put the bamboo skewer through the straw on the bottle, and then install the prepared bottle cap on the bamboo skewer as the wheel of the car, and coat the wheel with hot melt glue to prevent the wheel from falling off.

4. The power system of the car is mainly composed of the motor and the fan blade, the rotation of the motor and the fan blade will form a stream of airflow, due to the effect of land crack recoil, promote the car to move forward, and now use the bottle to make the fan blade.

5. First draw a circle with a marker pen in the place where the bottle is to be cut, and then use a utility knife to cut it according to the line drawn in advance, after cutting, we take the upper part, and then cut it evenly into pieces, but do not cut it to the end.

6. Since plastic has a certain memory, it will always be restored to its original appearance, at this time we need to burn it with a lighter, and then fix it to the way we need it.

7. After the fan blade is ready, I need to install it with the motor.

8. The assembly began, and the power system, that is, the motor with fan blades, was installed on the car.

9. At this time, we found that there is no battery holder, and the battery cannot be installed, so draw the place where the battery should be placed, and then proceed to the next step.

10. We use a utility knife to cut the part that needs to be cut in advance, and the battery is installed.

Here's how to make handmade toys:

1. Tumbler.

1. Materials: table tennis, white Zheng stove-colored cardboard, plasticine, colored pencils, glue, scissors, etc.

2. Production method:

1) Remove half of the table tennis ball with scissors, and pinch the plasticine into a ball and fill it in half of the table tennis ball and smooth it out.

2) Cut the white cardboard into a fan, the arc length of the fan should be slightly larger than the circumference of the table tennis ball, and make a conical shape on both sides of the fan.

3) Connect the paper cone with the table tennis ball sticky tassel, draw the head on the table tennis ball with colored pencils, and the white conical hat can also be decorated with familiar patterns or patterns for children. Such a cute tumbler is made.

In addition to this method, it can be made using a similar method using the bottom of the Sprite bottle (with the bottom tray removed) and the upper part of the bottle.

2. Water lotus.

This is a very popular toy for young children, and it can be used in all three grades: elementary, middle and large.

1. Materials: table tennis, masonry board.

2. Production method: cut the table tennis ball in half, trim the edge into a toothed (flower-shaped), or cut half of the table tennis ball in half, and then cut it in half into a two-pointed boat.

3. How to play: Smear some water on the smooth masonry board, put the "lotus" or "boat" on it, tilt the mason board arbitrarily, you will find that the "lotus" is rotating at high speed, at the same time, you have to carefully control the mason board, do not let the "lotus" fall to the ground, because it rotates really fast, so children like to play non-stop.

The simple and fun way to make handmade toys is as follows: [Toy Newton Pendulum Ball] Materials and tools: popsicle sticks, cotton rope, glass balls, hot melt glue, white latex, scissors production steps:

The Newtonian pendulum was first proposed by the French physicist Edme Mariote in 1676. When swinging the rightmost ball and colliding with four other balls in a tight line-up during the swing, the leftmost ball will be ejected, and only the leftmost ball will be ejected. When the two rightmost balls swing at the same time and hit the other balls, the two leftmost balls are ejected.

The same is true for the opposite direction, and the base is for more balls, three, four, five or more. It is assumed that each metal ball is a particle of the same mass. When a particle hits the second particle, the momentum and energy of the first particle are immediately transferred to the second particle, and so on until the last particle gains momentum and energy and pops out.

The situation is still the same even if two or more particles hit a ball set. However, instantaneous motion requires an infinite acceleration and a mass of zero particles. When a moving ball hits a stationary ball, the compression wave will be transmitted in both balls.

The method of making handmade toys is as follows: tools: mineral water bottles, beverage bottle caps, scissors, utility knives, adhesive tape, fine ribbons.

1. First of all, we need to cut off the cone part on the top of the mineral water bottle. You can start by making a cut with a utility knife. 2. Cut it with scissors, taking care not to scratch your hands.

3. After cutting it out, we need to repair the edges neatly. 4. Then use the same method to cut off the base of the mineral water. 5. Remember to trim the edges.

6. Now put a few mineral water bottle caps into the cut cone. Be careful not to put too much, just fill the cone almost full. 7. Paste with adhesive tape.

8. Then use tape to stick the upper and lower parts of the mineral water together, preferably around the tape twice, so that it is stronger. 9. Then tie a ribbon under the bottle cap to decorate. A small handmade sandbell is done!

10. Make two and shake them in your hand, so that children can sing and dance with the rhythm, exercise children's hands-on ability, and cultivate children's sense of rhythm.

The steps of the process of making handmade toys are as follows: Prepare materials: toothpaste box, scissors, glue, tape, straw, bottle cap, plasticine.

Operation steps: 1. First of all, make the body of the car first, and cut one side of the toothpaste box out with an oblique opening, as shown in the figure. 2. Next, cut off the opening of the box, and then cut it into two parts, gluing them to the front and back respectively.

3. Then make a wheel, cut the straw short, then put both ends into the middle of the bottle cap, fill the bottle cap with plasticine, and fix the straw, as shown in the figure, such a wheel is the same as two standby. 4. After that, paste the wheels on the body as shown in the figure below. 5. Finally, flip the body over, and a handmade car is ready.